Question about 2010 Mercury Milan V6

Open Question

Rear brakes what is the procedure to compress rear calipers, tools etc.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
maklean
  • 1665 Answers

SOURCE: changing rear brake pads

http://www.automedia.com/Replacing_Brake_Pads/ccr20050701bp/1

Posted on Jun 26, 2008

Ad
  • 4369 Answers

SOURCE: replace rear brake pads on a 2000 grand marquis

rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Posted on Mar 15, 2009

scott_77
  • 48 Answers

SOURCE: rear caliper sticking ? after new pads installed

Did you drain excess fluid out of the reservoir?

Posted on Apr 30, 2009

shadytree
  • 25 Answers

SOURCE: rear brakes 05 merc montego

Try turning again clockwise with a little more pressure. If the brakes were worn badly the piston is just stuck from being adjusted out so far.

Posted on Jul 28, 2009

  • 196 Answers

SOURCE: I'm replacing brake pads on 2005 mercury montego

are you using the right tools? Id call you local auto parts store to make sure the set your using is correct, if it is the right set, id be asking how far out the piston is, on these newer vehicals, if you screw them out to far, almost to the point of being removed, they will not go back in or at least are very tricky to do

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to replacing rear brake pads


A special tool is required to compress the caliper piston on the rear brakes-don't use a C-clamp on the piston.
Raise the vehicle and remove the tire. The rear calipers have only one guide pin. Remove this pin and raise the caliper. Remove the old brake pads. Using the special tool compress the caliper piston-the piston will have one or two slots on it. These slots must in the correct position to remount the caliper. Install the new brake pads and slide the caliper back over the rotor and replace the guide pin. If the caliper doesn't slide over the rotor you'll need to reset the slots on the piston. Replace the tires and you're ready to go.

Jan 01, 2011 | 2000 Buick LeSabre

1 Answer

How do I change the rear brakes on a 2005 Audi A6? I have the pads and am ready to go, but I cannot get the piston on the rear brakes to compress. Is it just a matter of compressing it with C-clamps or...


You must be very careful or this brake job will get very costly, depending on the brake system on this car, one you may have the caliper type that you need to use a tool that turns the caliper piston while it slowly compresses it, then you may have the style caliper with electronic praking brake actuator then you will need a scan tool to do the job, hopefully you did not damage the piston,hope this helps,if theres a small module box on the caliper then you will need scan tool. if it just the caliper with a emergency brake cable going to it then you need the tool that turns the piston by the notches on the face of piston.

Aug 14, 2010 | 2005 Audi A6

1 Answer

How to change brake pads on 94aerodeck


front or rear? in front only need to remove the 2 screws of caliper, remove it and compress the caliper piston with a c-clamp put the new pads, caliper and tight the screws. For rear is the same procedure but need a tool for compress the caliper piston, looks like http://www.chain-auto-tools.com/pics/AMR450L.jpg and in this page is how to use need to turn clockwise and press for compress it http://image.superstreetonline.com/f/9520063/130_22_z+acura_rsx_s_brake_install+compress_piston.jpg

Jun 01, 2010 | 1994 Honda Accord

2 Answers

How to compress rear brake caliper piston 2007 vw


Only way is to use diagnistic equipment.Go to HAND BRAKE . There is option to release the pistons.When you change the brake pads you have to use option - engage .

May 12, 2010 | 2007 Volkswagen Jetta 2.5 Sedan

3 Answers

Compressing the rear disc brake caliper on 2008 grand caravan


The rear calipers on these models require a special tool that compresses and turns the piston in at the same time -- most parts stores carry this tool.

It is called a caliper piston press -- and it installs where the pads would go and acts like a c-clamp,when turning handle it will turn the caliper piston backinto the caliper as it compresses it.
Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the Parking Brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor,MILLER Special Tool 8807, . Any other seating method will damage the self-adjuster mechanism.
Good luck and hope this helps.

Mar 07, 2010 | Dodge Caravan Cars & Trucks

4 Answers

When trying to change the rear pads on a 2005 Montana SV6 I was not able to compress the caliper. It appears as if they need to have the pressure relieved from the system. Do I need to just apply more...


No, on rear wheel disc brakes, the pistons have to be turned in clockwise, and you need a special tool to do it, or you have something strong enough to put in the slots and turn it, but just turn them in far enough to get the new pads to slide over the rotors.

Nov 04, 2009 | 2005 Pontiac Montana SV6

1 Answer

What tools do you need to replace the rear caliper brakes on a for expedition xlt 2006


Standard repair tools except for a rear caliper compression tool. This is needed because rear calipers screw in due to parking brake.

Jul 11, 2009 | 2006 Ford Expedition

3 Answers

Unable to compress rear brake caliper is this caliper shot?


There is a tool that you can buy or rent at the parts house that you can connect to a hand tool EG: 3/8 rachet to use with a tool to compress the caliper while you turn the rachet. You will see some raised teeth on the calliper piston for the tool to bite on. Since the rear brake is used to lock the parking brake it has to have a self adjust to compensate for the brake pad wear. EG: Old school drum brakes adjust when you back up depressing the brakes and letting off while the vehicle is rolling allows for the adjuster to reset the brake shoe clearance.

Jun 01, 2009 | 2004 Pontiac Bonneville

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

Not finding what you are looking for?
2010 Mercury Milan V6 Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...