Question about 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Ball joint lower knuckle - 2007 Dodge Caliber SXT Sport Hatchback

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 509 Answers

Replace every 2 years is standard practice for the Calibers.

Posted on Sep 12, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: Remove Upper/Lower Ball Joints

The only way is to press them out with a press, and press the new ones in. I have seen people try to press them out with a vise and a socket against the balljoint and it did not work, a local machine shop or repair shop should have a press.

Posted on Oct 13, 2008

  • 333 Answers

SOURCE: upper and lower ball joints

Your better off have it done bt a tech because you need a press to press them out and in. Also you will have a warranty witk the work. You want to be safe messing with your steering and suspension. I hope this helps.

Posted on Dec 05, 2008

  • 3 Answers

SOURCE: front hub bearing removal 2002 dodge ram 1500 4WD 4.7L V8

i just did a 2002 2500 4x4 with a dana straight axle and had no problem getting on the bolts with a 9/16 12 point socket on a 6 inch extension. If you do not use an extension the head of the ratchet will hit the yoke of the axle shaft.

Posted on Feb 18, 2009

  • 63 Answers

SOURCE: Six hours to replace '05 Dakota lower ball joints?

well when you get a estimate they go by a general book time that it should take they are usally over by an hour or so but not very far off. you could try your self and see how long it takes

Posted on Mar 20, 2009

  • 72 Answers

SOURCE: Upper and lower ball joint replacement

to remove the axles, remove brake caliper and disc, remove hub assembly, the center hub/axle nut and...(there are i think 3-4 bolts on the back side of the spindle to remove the hub), you may have to force the hub off the spindle with a hammer or air hammer... once the hub is out the axle should slide out of the front differential allowing access to the ball joint nuts for removal...

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Latitude. How can I replace control arm and ball joint assembly?


Lower you can do fairly easy. Upper, a bit tougher.For the upper you will need a spring compressor.

Mar 21, 2016 | 2011 Jeep Patriot

1 Answer

How do i fix front right ball joint for 2001 mazda protege lx?


SAFELY RAISE SUPPORT FRONT OF VECHICLE ON JACK STAND MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. REMOVE WHEEL OR TIRE. REMOVE BALL JOINT STUD PINCH BOLT AND NUT FROM THE STEERING KNUCKLE.REMOVE BALL JOINT BY PRYING IT FROM THE KNUCKLE.REMOVE BALL JOINT TO LOWER CONTROL ARM BOLT AND NUT. INSTALL NEW BALL JOINT TO LOWER CONTROL ARM.TORQUE THE BOLT TO 86 FT LBS INSTALL BALL JOINT TO THE STEERING KNUCKLE TORQUE BOLT TO 43 FT LBS YOU MORE LIKELY NEED FRONT END REALIGNMENT AFTER THE JOB DONE.

Sep 09, 2011 | Mazda Protege Cars & Trucks

1 Answer

Front right hub and sensor assembly or a diagram


stevenhurc_11.jpg

Removal Steps

1. Torsion bar

2. Wheel speed sensor

(if equipped with ABS)

3. Back plate

4. Lower ball joint

5. Upper ball joint

6. Knuckle assembly

7. Oil seal

8. Thrust washer

9. Needle bearing

10. Knuckle

Installation Steps

10. Knuckle

9. Needle bearing

8. Thrust washer

7. Oil seal

6. Knuckle assembly

5. Upper ball joint

4. Lower ball joint

3. Back plate

2. Wheel speed sensor

(if equipped with ABS)

1. Torsion bar

Mar 01, 2011 | 1999 Isuzu Trooper

1 Answer

Need to replace ball joints


http://groups.yahoo.com/group/villagerquest/ Ball Joint Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the suspension lower arm ball joint cotter pin.
  1. Remove the suspension lower arm ball joint nut and separate it from the wheel knuckle.
May have to leave nut partially on and hit the nut hard with a hammer to knock the tapered stud down and out. May have to hit side of knuckle to help get it to drop. or rent a pickle fork to drive between the bal joint and knuckle.
  1. Remove the suspension lower arm ball joint to suspension lower arm nuts and remove the ball joint.

Nov 15, 2010 | 2001 Nissan Quest

1 Answer

How to replace a lower ball joint on a 1988 pontiac grand prix hit a pothole and it popped out


Hope this helps and please don't forget to rate! Thank you!


e8fbd9d.gif
Front ball joint with heat shield

Remove and Replace-

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the front wheel and tire assembly.
  4. Unfasten the retaining bolts, then remove the ball joint heat shield.
  5. Remove and discard the lower ball joint cotter pin.
  6. Remove the ball joint nut.
  7. Loosen, but do NOT remove, the stabilizer shaft bushing assembly bolts.
  8. Separate the ball joint from the strut/knuckle assembly using ball joint/tie rod puller J-35917 or equivalent.
Do NOT damage the halfshaft boots when drilling out the ball joint rivets.
  1. Drill out the rivets retaining the ball joint to the knuckle strut assembly and remove the ball joint from the knuckle. Use a 1/8 in. drill bit. Refer to the instructions in the ball joint replacement kit.
To install:
  1. Position the lower ball joint in the strut/knuckle assembly.
  2. Install the four ball joint bolts and nuts, as shown in the ball joint kit and tighten to specifications.
  3. Install the ball joint-to-lower control arm. Install a new ball joint-to-lower control arm nut.
  4. Tighten the stabilizer shaft bolts to 35 ft. lbs. (48 Nm).
  5. For 1988-91 vehicles, tighten the ball joint-to-lower control arm nut 15 ft. lbs. (20 Nm) plus at least an additional 90° (11/2flats), plus enough to align the cotter pin hole. Do NOT overtighten.
  6. For 1992-96 vehicles, tighten the lower ball joint nut to 63 ft. lbs. (85 Nm). Tighten to align the next slot in the nut with the cotter pin hole in the stud. Do NOT tighten more than 60° (1 flat) to align with the hole.
  7. Install a new cotter pin.
  8. Position the ball joint heat shield and secure with the retaining bolts. Tighten to 62 inch lbs. (7 Nm).
  9. Install the front wheel and tire assembly, then carefully lower the vehicle.
  10. Connect the negative battery cable and check for proper suspension operation

Apr 26, 2010 | 1988 Pontiac Grand Prix

1 Answer

How to replace lower left front ball joint ?


Removal & Installation NOTE This procedure requires the use of the following special tools: J 9519-E Lower Ball Joint Remover and Installer, J 34874 Booster Seal Remover/Installer, J 41435 Ball Joint Installer, J 45105-1 Ball Joint Flaring Adapter and J 45105-2 Receiver.

  1. On 4WD vehicles, remove the wheel center cap and drive axle nut.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Tire and wheel
    • Wheel hub and bearing, if necessary
    • Outer tie rod retaining nut
    • Out tie rod from the steering knuckle using a suitable puller
    • Brake hose bracket retaining bolts and bracket
    • Upper control arm-to-steering knuckle pinch bolt and nut
    • Upper control arm from the steering knuckle
    • Lower ball joint retaining nut
    • Steering knuckle from the lower control arm using a suitable ball joint removal tool
    • Steering knuckle from the vehicle
    • Lower ball joint flange with a chisel
  4. Install tools J 9519-E and J 34874 to the lower ball joint, then use those tools to remove the lower ball joint from the lower control arm.
To install:
  1. Install or connect the following:
    • Lower ball joint to the lower control arm, using tools J 9519-E, J 41435 and J 45105-2
  2. Remove the tools from the lower control arm.
    • Tools J 9519-E and J 45105-1 to the lower ball joint
  3. Flare the lower ball joint flange with J 9519-E and J 45105-1, then remove the tools from the lower ball joint.
    • Steering knuckle to the lower control arm
    • Lower ball joint retaining nut and tighten to 81 ft. lbs. (110 Nm)
    • Upper control arm to the steering knuckle
    • Upper control arm pinch bolt and nut and tighten to 30 ft. lbs. (41 Nm)
    • Brake hose bracket to the steering knuckle
    • Brake hose bracket retaining nuts and tighten to 7 ft. lbs. (10 Nm)
    • Outer tie rod to the steering knuckle
    • Outer tie rod retaining nut and tighten to 33 ft. lbs. (45 Nm)
    • Wheel hub and bearing, if removed
    • Tire and wheel
  4. Lower the vehicle
    • Drive axle nut, if 4WD, and tighten to 103 ft. lbs. (140 Nm)
    • Wheel center cap, if removed
  5. Check the front wheel alignment.

Nov 30, 2009 | 2002 Oldsmobile Bravada

1 Answer

Emissionwiz has asked you to clarify your question to best assist with your how to remove the lower ball joint, trooper problem: do u have the ball joint press?The ball joint is presse3d out; the problem...


the upper or lower ball joint is bolted into lower control arm or upper control arm
to remove from knuckle possibly has split pin to remove first before undoing nut. leave nut on ball joint (finger loose) but so you cant see any thread from shaft and use ball joint splitter to seperate or hit side of knucle with ball peine hammer to jolt tapper shaft of ball joint loose from knucle(dont hit to of ball joint shaft)then to remove nut you have to lift top arm & or knuckle to get between driveshaft

Jun 29, 2009 | 1998 Isuzu Trooper

2 Answers

Repair lower ball joints


The front lower ball joints are pressed into the steering knuckle. Once the brake components are removed, the CV shaft nut and tie rod ends can be removed. Remove the front strut bolts, and the lower ball joint nut. Separate the lower arm from the ball joint. Once the knuckle assembly is off the car remove the lower joint snap ring and dust boot. Utilizing a ball joint press (should be able to rent from local parts store) press the joint out of the knuckle. Re-installation is naturally reverse of removal. I hope this helps.

Sep 24, 2008 | 1999 Ford Taurus

1 Answer

Lower ball joint removal how to


  1. Remove the steering knuckle with wheel hub and bearing attached.
  2. Remove the lower ball joint flange with a chisel.
  3. Install J9519-E and J34874 to the lower ball joint.
  4. Remove the lower ball joint from the lower control arm using J9519-E and J34874


  1. Install the lower ball joint and J9519-E, J41435, and J45105-2 to the lower control arm.
  2. Install the lower ball joint to the lower control arm using J9519-E, J41435, and J45105-2.
  3. Remove J9519-E, J41435, and J45105-2 from the lower control arm
    1. Install J9519-E and J45105-1 to the lower ball joint.
    2. Flare the lower ball joint flange using J9519-E and J45105-1.
    3. Remove J9519-E and J45105-1 from the lower ball joint.
    4. Install the steering knuckle with wheel hub and bearing attached. Install the tire and wheel.
    1. Lower the vehicle.
    2. Check the front wheel alignment.
these jouints are pressed in and there is a flange that is flared this is what the tool numbers refer too.

Sep 12, 2008 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
2007 Dodge Caliber SXT Sport Hatchback Logo

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...