Question about Cars & Trucks

1 Answer

Carealero problem My car is revving up on its own, especially when I put it in park. The rpms go up to, if I put it in N it goes up a little, reverse it backs down a little and park it goes crazy.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 41 Answers

The throttle cable or linkage might be sticking. Take the vehicle to a repair shop that you trust, they can probably find the problem.

Posted on Jan 02, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: My 2000 Accent GL is reving into HIGH RPMs! 5 speed 1.5 L

check your anti freeze and watch your temp gauge.any check engine light on.

Posted on Nov 15, 2008

  • 64 Answers

SOURCE: suddenly automatic transmission would not go into reverse

seems like your gear linkage is either broken or come off, if the linkage is ok then u are looking at a replacement gearbox

Posted on Mar 02, 2009

  • 54 Answers

SOURCE: motor

It's one of two things, either the idle air control valve is going bad, or you have air in the cooling system. Check and see if have any kind of coolant leak, if not it's the idle air valve. I run into the air in the coolant system more than anything on those cars and it doesn't take much air in the system to cause the problem you are describing. Good luck hope this helps.

Posted on May 28, 2009

  • 1071 Answers

SOURCE: Integra revs RPMs when idling

idle air control motor or just a plain old vacuum leak

Posted on Jul 21, 2009

  • 28 Answers

SOURCE: car will not shift out of park and yes the brake is being pressed

Shifter assemblies are a common problem with these vehicles (floor shift models). An audible click should be heard in the shifter area when the brake pedal is depressed (if not, you may have an electrical issue in the btsi curcuit, see a qualified repair facility). Hope this helps you, good luck

Posted on Jul 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rpm rev upward when car is idling in park


Auto idle in cold weather most new cars do it to warm up engine faster

Feb 19, 2015 | Cars & Trucks

1 Answer

2000 mercury cougar is revving rmp when in park


It sounds like a malfunctioning throttle sensor.

Jan 28, 2014 | 2000 Mercury Cougar

2 Answers

How do you adjust the shift cable on a 1995 gmc jimmy, wont go into reverse or park.


On the 1995 Jimmy, the shift cable can come loose on the mount on the side of the transmission where the cable meets the trans. When it slips, the alignment goes off and causes the driver to not be able to put the trans into park. If you take a long stick you can push the shift arm on the trans to the park position and your trans will go into park.....what you (and I) really need to know is how to take the shift cable mount apart and reset it.

Aug 05, 2012 | GMC Jimmy Cars & Trucks

1 Answer

I put the car in park on a little incline and it would'nt go into reverse it was stuck and i had a hard time with gear shaft, i held the brake and tried to pull it back to reverse and it wouldn't go, my...


The parking mechanism in the transmission has a shaft which slides into a V shaped groove. This is designed to make it easier to put the car in park. The bad part is that it allows for a little movement. The best way to prevent this from happening again is to engage the parking brake when you put it in park, especially on an incline. This will prevent the rollback you experienced from happening again. Hope this helps.

Aug 14, 2010 | 2005 Chrysler 300

1 Answer

1993 Bronco 5.8L, dies in reverse, and in low forward


not sure on your year but check the modulator on the transmission. remove the vacuum line at the modulator and see if there is any tranny fluid there. if the there is change the modulator.

Jan 15, 2010 | 1993 Ford Bronco

1 Answer

Car will not chnage from park position when put in reverse,drive


I think there is a cable for this that goes to the transmission. Problems with them are broken cable, or loose cable clamp especially on the transmission end. It is also possible that the end attached to the transmission detent got unattached, or the end to the shifter did. Rick

Apr 10, 2009 | 1995 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...