Question about Cars & Trucks

Open Question

Belt adjustment need to agust

Posted by on

  • Bill Boyd Jan 02, 2014

    Hi John Vogel, I want to help you with your problem, but I need more information from you. Can you please add details in the comment box? what belt needs adjusting

  • Jose Ruppenschlager
    Jose Ruppenschlager May 07, 2014

    Also, if you can add what type of car. Year make and model that would be useful information.



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to agust tappets on a 250 pre cross flow ford 6

If you have hydraulic lifters(tappets) then you turn the adjusting screw 1/4 turn past the point where there is no noise from the rocker arm. If you have solid lifters, then you'll have to get the cold clearance spec for that engine and adjust accordingly.

Dec 13, 2014 | Ford Cars & Trucks

1 Answer

How to agust clutch on petrol club cart

Don't know much about that brand but most has a clutch Rod or cable that you can adjust out more, Just follow from peddle. Sorry not much more help good luck with it.

Dec 05, 2011 | Cars & Trucks

1 Answer

Clutch pedal to high is a new clutch cable required or can it be agusted manually for my honda crv 2000

When the clutch pedal gets high that means the clutch disk is worn out, as the disk thins from wear the clutch pressure plate springs move outward, that raises the pedal height. As far as a cable goes this car doesn't have one, the clutch is hydraulic, and all hydraulic clutches are self adjusting.

Jan 06, 2011 | Honda CR-V Cars & Trucks

2 Answers

I cannot adjust the alternator belt for my ford transit 2002

get new belt maybe strecth.dont this have tensioner's. is belt loose coming off or what the reason to adjust.

Dec 11, 2010 | Ford Transit Connect Cars & Trucks

1 Answer

How do i find out how long to make my pushrod on aluminum heads i have a agustable pushrod i got from summit raceing i have a 302 ford with roller rockers

put the rocker arm on get lifter on backside of cam ajust pushrod so rocker tip is in the center of valve then measer pushrod

Nov 27, 2010 | 1966 Ford Mustang

1 Answer

I have a broken belt that goes on the same pulley that another belt is already on. What all do I have to remove to be able to put the belt on. I guess the belt that needs put on is for the heat & air...

A/C Compressor Belt
  1. Remove the alternator/power steering and water pump drive belt to gain access to the air conditioning belt.

  2. Loosen the tensioner pulley locknut, then turn the adjusting screw to raise or lower the tensioner pulley assembly. Remove the belt.

To install:

  1. Install the belt.

  2. To adjust the belt, loosen the tensioner pulley nut and adjust the belt tension by tightening the adjusting screw. Tighten the pulley nut to 40 ft. lbs. (54 Nm) after adjustment.

  3. Install the alternator/power steering and water pump drive belt and adjust.

  4. Start the engine and check for proper belt alignment and any abnormal noise.

Nov 01, 2010 | 1995 Dodge Intrepid

1 Answer

Loud squeal noise from serpentine belt on 99 dodge truck with 318 motor when its cranked up

If you have an manual adjuster you need to tighten or replace the belt, belt treatment may help.
If you have an automatic adjuster. You can try belt treatment, if it doesn't work you'll need to replace the belt and maybe the adjuster.

Jun 06, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer


serpentine belts dont need adjusting they have a tensioner pulley that is spring loaded / you may need a new tensioner pulley or belt . hope that helps

Jan 30, 2010 | 1998 BMW Z3 Roadster

1 Answer


take out the fan first, then u'll see the alte. on the bottom left of engin, take the bolt from the top of alte. and the aguster bolt from the bottom of it.(u'll see the belt becomes loss) there is 3 wires that u have to take out, and u done.

thank you sir

Jun 16, 2008 | 2003 Cadillac CTS

2 Answers

1998 dodge neon airconditioning belt adjustment?

This procedure involves correcting the tension on the power steering accessory and A/C compressor drive belt.

1. Loosen the power steering pump locking bolts A and B and pivot bolt C(Illustration 1 and 2 ) to allow adjustment of belt tension.
2. Using a 1/2" breaker bar, adjust belt tension by applying torque to the square hole "D" on the power steering pivot bracket. Adjust the tension as follows:

Belt tension with no belt replacement: A. Using the Belt Tension Gauge Special Tool Kit C-4162, adjust the belt tension to 100 lb.
B. Tighten in order, first tighten the locking bolt A to 27 Nm (20 ft. Ibs) then, bolt B to27Nm (20 ft. Ibs). Finally tighten the pivot bolt C to 54 Nm (40 ft. Ibs).
Belt tension with belt replacement:
A. Using the Belt Tension Gauge Special Tool Kit C-4162, adjust the belt tension to 135 lb.
B. Tighten in order, first tighten the locking bolt A to 27 Nm (20 ft. Ibs) then, bolt B to 27Nm (20 ft. Ibs). Finally tighten the pivot bolt C to 54 Nm (40 ft. Ibs).
C. Start the engine and allow the vehicle to idle for 15 minutes to allow the belt to seat.
D. Repeat the belt tensioning procedure, set belt tension to 135 lb.

click here for picture 1
click here for picture 2

Jun 13, 2008 | 1998 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides