Question about Cars & Trucks

1 Answer

Knock sencor problem were do I find it on A 03 Nissan etterra

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 52 Answers

Knock sensor is on the side of the block under the exhaust manifold. Either the drivers side or the pass side, just depends.

Posted on Jan 02, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is a knock sencor. can show me an image inside the engin?


A knock sensor detects pre-ignition (ping). It is an engine protection device which retards ignition timing when pre-ignition is detected. Normally located on the engine block behind the exhaust manifold

Aug 13, 2015 | Cars & Trucks

1 Answer

Where is the knock sencor on a 1992 Blazer


The knock sensor is J, in the picture. Note vin.knock-sencor-1992-blazer#solution-section-tgdpj5bc1lhzttcuvramaekd-2-0.jpg

Nov 16, 2014 | Chevrolet Blazer Cars & Trucks

1 Answer

Knock sencor on 1999 Trans Am.


Location of the knock sensors? I think this is the LS motor and they are under the Intake manifold ...here is picture link..

Jun 14, 2014 | Cars & Trucks

1 Answer

Nissan online mechanic


code p 0432 is main cat converter bank 2 --efficiency below threshold ===causes -- cat converter---wiring heated oxygen sensor (HO2S ) in the bank 2 manifold before the cat converter
ave a compression test done to determine inlet valve seat insert loose
if you have a problem with it there should be a bit of a miss, or it should change with rpm
could be a cam lobe failing and the noise should change with rpm

Aug 07, 2017 | 2003 Nissan Maxima

3 Answers

Nissan pathfinder 1998 code p0325 what sencor is it there are 4 Sencors ???


It is the knock sensor. But before you do anything first check the vacuum line which is on the front right tire on the rear side of the tire where small hose from charcoal canister up over the shock to the purge valve. That vacuum hose from the purge valve connected to a metal hose and then the metal hose connected back to a rubber hose on the purge valve. that metal hose because it gets rusted cause a leak causing Injector 2 to missfire.

Aug 18, 2012 | 1998 Nissan Pathfinder

1 Answer

Where is the knock sensor located on an 03 nissan altima


Hello and thank you for using FixYa!

The knock sensor is located on the back side of the engine block by the oil pressure switch, under the intake, but accessible from underneath the car.

Thanks Jay!

Jul 10, 2009 | 2003 Nissan Altima

1 Answer

Car will not turn over. commputer says correlation sencor A bk 1


your crank sensor is on the lower firewall side of the engine. It goes directly into the block and has one small bolt reataining it. I take that back. I thought car was an 02. 03 sensor is still on the lower side of the block but is at the front kinda above and behind the starter. 03 was more of a pain to get to. Hope this helps

Mar 26, 2009 | 2003 Chrysler PT Cruiser

1 Answer

1992 nissan maxima timing belt replacement


need to take off almost every thing from the front of the motor. then take off top half of timing cover.
pull the harmonic balance pully off. then the bottom half of the cover will come off. becareful
the cam gears are hard to aline.
do you no where the knock sencor is located?
if so please email me @ goodedgeworth@gmail.com

Mar 07, 2009 | 1992 Nissan Maxima

1 Answer

1993 full size blaser 5.7 code 43


Check for a 5 volt reference signal at the wiring to the knock sensor. With key on engine off one of the wires to the sensor should have 5 volts.

Dec 26, 2008 | 1993 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...