Question about 2006 Nissan Altima

1 Answer

Remove alternator how to replace a alternator on a nissan altima 2006 3.5

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Nissan Master
  • 803 Answers

Remove radiator and fan assemblies for easier access. Disconnect battery, disconnect wiring from alternator, remove belt and two bolts ,upper and lower that hold alternator. Wiggle and pry alternator free. Be careful not to bump into a/c condenser.

Posted on Jan 02, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ilragatzzo78
  • 241 Answers

SOURCE: Replacing a starter for a 1999 Altima

  1. Disconnect battery ground cable.
  2. Disconnect starter wiring from starter.
  3. Remove starter retaining bolts and the starter.
  4. Reverse procedure to install.
the bolts should be on the drivers side.
you will have to crawl underneath the car to do this task

Posted on May 15, 2008

  • 1 Answer

SOURCE: 2003 Nissan altima alternator

how do yow remuve alternaotor on a 2003 nissan altima

Posted on Jan 05, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

ZJLimited
  • 17970 Answers

SOURCE: How do you remove a 1999 Nissan Altima starter?

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Posted on Apr 05, 2010

smhb1
  • 146 Answers

SOURCE: How do I replace the alternator on a 2005 Nissan Altima?

first things you have to do to change nissan altima 2.5 alternator?
1- disconnect battery
2-from the top of alternator there will be 3 thing u have to open one is with bolt 12 mm and second is with screw star.
3-turn the starting full right there will be small cover 2 plastic clip and one 10 mm bolt.
4-from the down take 12 mm and turn the pulley which is bellow alternator with press.
5- take belt out (note that u have to draw the map of belt be4 take it out.
6-and install alternator back again in same steps.

Posted on Sep 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get the bolts loose from the alternator for a 2003 Nissan altima 3.5


Kathy, R&R info./instructions in links below. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
2003 nissan altima 3 5l v6 alternator part 1
how to replace the alternator on 2003 nissan altima 3 5L alternatoe...
2003 nissan altima 3 5l v6 alternator install 1
2002 Altima Alternator How Do Replace the Alternator on My 2002


Jun 16, 2016 | 2003 Nissan Altima

2 Answers

I try to start my Nissan Altima 2006 and its like the starter is dragging I replaced the starter but still does the same can someone help me please


Was any major work done to it recently? If not find some who has experience and ask them to take another car and use 24 volts to start it once and it may start and be fine. When I rebuild engines I have to do this sometimes. PLEASE MAKE SURE THE PERSON KNOWS EXACTLY WHAT THEY'RE DOING.

Dec 13, 2014 | 2006 Nissan Altima

1 Answer

Problem with 2006 Nissan Altima 2006 nissan


Coil packs are located on top of spark plugs, one for each cylinder.

Aug 25, 2013 | 2006 Nissan Altima

1 Answer

I cant find the oil pump on a 2006 Nissan Altima


On both the four cylinder and six cylinder engines the oil pump runs off the crank shaft. The front cover and timing chain needs to removed in order to replace or repair the oil pump. It is not a very common repair. Is there a reason you are looking for it?

Apr 09, 2013 | 2006 Nissan Altima

1 Answer

Need to change out back brake light on 2006 nissan


take interior cover behind tail light inside trunk off.the bulb the bulb twist locks in hole(twist counter clockwise to remove)repeat procedure to replace.

Mar 23, 2010 | 2006 Nissan Altima

1 Answer

How to replace knock sensor in 1995 nissan altima


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Jan 20, 2010 | 1995 Nissan Altima

1 Answer

1995 Nissan Altima - replacing alternator


Yes.  Have him purchase a Haines or Chiltons Manual at Auto Zone or similar store.  I have changed 2 alternators on my 95 Altima in my time and I am not an expert mechanic.  Also check out:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528007871b

Pretty good primer for the novice.

I did not remove the belt all the way. Merely slipped it off the old alternator pulley and then slip the new alternator onto the old belt and then tightened/adjust the belt as needed when done.
Good luck.

Nov 09, 2008 | 1995 Nissan Altima

3 Answers

2003 Nissan altima alternator


The alternator is right on top of the 2.5L motor and held on by 2 14mm bolts. To remove the lower bolt (hard to reach), you must remove the coolant bottle and the IPDM fuse board and its metal box/bracket. A breaker bar really helped give enough torque to loosen the bolts. Approach the drive belt from under the front passenger tire. There is a tension adjuster (hard to reach) bolt that loosens the belt and allows you to remove it from the alternator.

Aug 21, 2008 | 2003 Nissan Altima

Not finding what you are looking for?
2006 Nissan Altima Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...