Question about 2000 Toyota Corolla

1 Answer

2000 toyota corolla ce motor trembling when on drive holding down brakes.

I have a 2000 toyota corolla ce and the motor is vibrating when car you have your brakes on while on drive. also,the check engine light just came on. the car drives great and I gave it a partial tuneup three weeks ago. I changed the spark plugs, oil, and filters. I tookit to one machanic who told me it was the motor mounts and transmission mounts which he changed but the car is still the same. Does anyone have any idea what this is.

Posted by on

  • lialmade May 11, 2010

    I have similar problem, did you find out what is wrong?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 347 Answers

Check the brake disks. surface should be cleaned. also check the brake pads.

Posted on Sep 20, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MauiRentaCar
  • 288 Answers

SOURCE: Car trembles while on Drive as soon as one halts by applying brakes

The most important engine mount for reducing vibration is the right front engine mount, which attaches the timing belt cover to the inside fender. Make sure this one has been replaced. The result is very noticeable. If defective or cracked, this mount can be difficult to diagnose visually, so usually it will still look ok even when it is not. In many cases I've seen mechanics replace only the front mount which is under the radiator - usually this does not give any appreciable reduction in vibration. The rear mount and left mount can reduce vibration a little bit further, especially when the car is in reverse. However the right front mount will usually take out 99% of your vibration. This is usually one of the first things I get done when overhauling a car for my rental fleet to Toyota Corollas.

Frank
Frank's Friendly Cars Maui Car Rental
www.MauiCarRental.biz

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Interchangeable parts


Canadian parts differ from Us and Mexico. Using a US part will decertify Canadian motor vehicle standards. I wouldn't try using anything but Canadian parts

Mar 19, 2017 | Toyota Corolla Cars & Trucks

1 Answer

Corolla 2000 brakes, I did change master cylinder,


System may have air in it bleed from farthest wheel to closest.
If rear shoes are out of adjustment re adjust them
Possible but most pads require a "bedding in" 20 stops 50 to25mph or so.

Jul 28, 2010 | 2000 Toyota Corolla

1 Answer

2005 toyota corolla ce is overheating when a/c is and i'm stopped


multiple corrections.. possible thermostat,fan, coolant. waterpump etc

Jul 18, 2009 | 2003 Toyota Corolla

2 Answers

2000 Toyota Corolla Vibrates


try giving a good tune up gas filter cap, rotor,wires,plugs,should feel a dramatic change

Jun 25, 2009 | 2000 Toyota Corolla

1 Answer

2000 Toyota Corolla, vibrates when brake on and in reverse, check


check the coil. you can switch them around to see if the code changes to the cly that has the coil from the #1 cly.thats the fastest way to check the coil.

Jun 16, 2009 | 2000 Toyota Corolla

4 Answers

2005 toyota corolla ce maint. required need to know how to reset.


To reset the system. Turn the ignition key to the "OFF" position with the odometer reading shown. Turn the ignition key to the "ON" position while holding down the trip meter reset knob. Hold down the knob for at least 5 seconds. The odometer indicates "000000" and the light goes off. If the system fails to reset, the light will continue flashing.

Jun 12, 2009 | 2005 Toyota Corolla

2 Answers

Car trembles while on Drive as soon as one halts by applying brakes


you should find a workshop equipped with a diagnostic computer. it should tell you whats wrong with your car.

May 28, 2009 | 1996 Toyota Corolla

1 Answer

Removing door panel in 2000 toyota corolla


remove phillips scew and the door handle. remove padded arm rest on the door by lifting it up, and remove 2 screws. You can use a panel tool to remove the plastic toggle like pins holding the panel border in. Be as gentle as possible they may break due to becoming brittle.

Apr 01, 2009 | 2000 Toyota Corolla

1 Answer

Trembles a little and suddenly turns off


when it does this ,see if black smoke coming from tailpipe...could be your oxy sensor not reading fuel ratio ...age seems about right for bad sensor...also if you change this ,take car for a good driveapp.20 mi. to let new sensor get a good reading on fuel /air mix coming from engine exhaust

Nov 25, 2008 | 1999 Toyota Corolla

Not finding what you are looking for?
2000 Toyota Corolla Logo

Related Topics:

627 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...