Question about Cars & Trucks

1 Answer

How to install distributor - Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to set distributor in 2002 gmg sierra 4.3

Posted on Mar 08, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need firing order on 96 Chevy Silverado and how to place the distributor


Distributor

ABCDEFGHIJKLMNOPQRSTUVWXYZ

Inspect/Replace

To Remove
  • Disconnect the distributor wiring connector and the vacuum advance hose, if the vehicle is so equipped.
  • Remove the distributor cap and note the position of the rotor. Mark the position on the distributor housing.
  • On some vehicles, it may be necessary to remove the spark plug wires from the cap prior to cap removal.
  • Note the position of the vacuum advance, then remove the distributor holddown bolt and clamp.
  • Pull the distributor from the engine. Most distributors will need to be twisted as they are pulled out of their bore.
  • Once the distributor is removed, install a shop towel in the distributor opening to keep foreign material out of the engine block.
  • The entire assembly should be cleaned thoroughly. Make sure all solvent residue is completely removed.
Installing and Timing a Distributor
The following procedure may be followed to install the distributor and time it to the engine, if all reference marks were made during the removal of the distributor:
  • Lubricate the O-ring on the distributor shaft.
  • Position the rotor so that it is aligned with the mark made on the distributor housing prior to removal.
  • Align the distributor housing with the mark made on the engine block during removal.
  • Lower the distributor into the engine block, making sure the distributor drive is fully seated.
  • Distributors equipped with a helical drive gear will rotate at the distributor is being installed, causing the distributor to move away from the reference marks.
  • Pay attention to how much the rotor moves.
  • Remove the distributor and move the rotor backward the same amount. This should allow the shaft to rotate while the distributor is being installed and still be aligned with the reference marks.
  • Make sure the distributor housing is fully seated against the engine block. Sometimes it may be necessary to wiggle or rock the distributor to seat it fully into the drive gear.
  • Distributors with drive lugs must be mated with the drive grooves in the camshaft. Both are offset to eliminate the possibility of installing a distributor 180 degrees out of time.
f22-52.gif The distributor must be aligned with the camshaft drive to seat the distributor in the engine block or cylinder head.
  • Rotate the distributor a small amount so the timer core teeth and pick-up teeth are aligned.
  • Install the distributor holddown clamp and bolt, leaving the bolt slightly loose.
  • Install the spark plug wires in the direction of distributor shaft rotation and in the cylinder firing order.
  • Connect the distributor wiring connectors. The vacuum advance hose is usually left disconnected until the timing is set with the engine running.
If the engine has been cranked while the distributor is removed, or no marks were made during removal, use this procedure to reinstall the distributor:
To be sure that the number one cylinder is on its compression stroke, observe the rocker arms to see that they are both moving. Then, rotate the crankshaft one revolution until the rocker arms for the companion to cylinder number one are both moving at TDC (top dead center). Align the timing mark and install the distributor with its rotor pointing to the number one spark plug cable in the distributor cap.
f22-01.jpg
  • Remove the spark plug from cylinder #1. Install a test plug in the end of the spark plug wire and position the test plug away from you and cylinder #1.
f22-02.jpg
  • Place your thumb over the bore for the spark plug and crank the engine until compression is felt.
f22-03.jpg
  • Lightly crank the engine while observing the timing marks on the crankshaft pulley. Once the timing marks are aligned, stop cranking.
f22-04.jpg
  • Identify the position for the #1 spark plug wire on the distributor cap.
f22-05.jpg
  • Determine which way the distributor shaft will rotate when it is lowered onto the camshaft gear. Then position the rotor so that it will be under the #1 terminal on the distributor cap after the distributor gear is meshed with the camshaft gear.
f22-06.jpg
  • After the distributor is installed in the engine, turn the distributor housing slightly so the pickup coil is aligned with the reluctor.
f22-07.jpg
  • Install the distributor holddown clamp and bolt. Hand tighten the bolt.
f22-08.jpg
  • Connect the pickup leads to the wiring harness.
f22-09.jpg
  • Install the spark plug wires onto the distributor cap according to the engine's firing order. Check to make sure everything that was disconnected before the distributor was removed, is now connected. Connect a timing light and prepare the engine for an ignition timing check and adjustment.

Feb 17, 2013 | Cars & Trucks

2 Answers

How to remove distributor on 1994 nissan pathfinder


Hi there:
Check this removal procedure (See Figures 1 through 5)

  1. Disconnect the negative battery cable.
  2. Unfasten the retaining clips (only remove the coil wire if necessary) and lift the distributor cap straight off. It will be easier to install the distributor if the spark plug wiring is left connected to the cap. If the plug wires must be removed from the cap, mark their positions to aid in installation.
  3. Remove the dust cover and mark the position of the rotor relative to the distributor body; then mark the position of the distributor body relative to the engine block.
  4. Detach the harness assembly connector.
  5. Remove the pinch-bolt and lift the distributor straight out, away from the engine. The rotor and body are marked so that they can be returned to the position from which they were removed. Do not turn or disturb the engine (unless absolutely necessary) after the distributor assembly has been removed.




6_26_2012_2_15_23_pm.jpg

Exploded view of the distributor assembly-6-cylinder engine




6_26_2012_2_15_51_pm.jpg

Align the mark on the housing with the mark on the shaft-VG30i and VG30E engines


6_26_2012_2_16_14_pm.jpg


After the distributor assembly has been installed, the rotor should be in this position-VG30i and VG30E engines


6_26_2012_2_16_40_pm.jpg

After the distributor assembly has been installed, the rotor should be in this position-KA24E engine



INSTALLATIONTiming Not Disturbed

  1. Insert the distributor in the block and align ALL matchmarks made during removal.
  2. Engage the distributor driven gear with the distributor drive.
  3. Install the distributor clamp and secure it with the pinch-bolt.
  4. Install the distributor cap and fasten the harness electrical connector.
  5. If necessary, install the spark plug wires and coil wire.
  6. Start the engine. Check the timing and adjust it if necessary.

Timing Disturbed
  1. It is necessary to place the No. 1 cylinder in the firing position to correctly install the distributor. To locate this position, the ignition timing marks on the crankshaft front pulley can be used.
  2. Remove the No. 1 cylinder spark plug. Turn the crankshaft until the piston in the No. 1 cylinder is moving up on the compression stroke. This can be determined by placing your thumb over the spark plug hole and feeling the air being forced out of the cylinder. Stop turning the crankshaft when the timing marks indicate TDC or 0 .
  3. Oil the distributor housing lightly where the distributor bears on the cylinder block.
  4. Install the distributor so that the rotor, which is mounted on the shaft, points toward the No. 1 spark plug terminal tower position when the cap is installed. Of course, you won't be able to see the direction in which the rotor is pointing if the cap is installed, so lay the cap on the top of the distributor and make a mark on the side of the distributor housing just below the No. 1 spark plug terminal. Make sure that the rotor points toward that mark when you install the distributor.

On the VG30i and VG30E engines, align the mark on the distributor shaft with the protruding mark on the housing.

  1. When the distributor shaft has reached the bottom of the hole, gently move the rotor back and forth slightly until the driving lug on the end of the shaft enter the slots cut in the end of the oil pump shaft and the distributor assembly slides down into place.

On the VG30i and VG30E engines, the distributor rotor tip should be in the 11 o'clock position.

  1. Fasten the distributor hold-down bolt.
  2. Install the spark plug into the No. 1 spark plug hole.
  3. Install the distributor cap and engage the harness electrical connector.
  4. If necessary, attach the spark plug wires and coil wire.
  5. Start the engine. Check the timing and adjust it if necessary.





Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Jun 26, 2012 | 1994 Nissan Pathfinder

1 Answer

I need the diagram for plug wiring for 1992 ford tempo


Firing order is 1-3-4-2 Please rate if this helps

Installation of wires
  1. Whenever a high tension wire is removed for any reason from a spark plug, coil or distributor cap, or a new high tension wire is installed, Silicone Dielectric Compound WA-10, D7AZ-19A331-A (ESE-M1C171-A) or equivalent must be applied to boot before it is reconnected. Using a small clean tool, coat entire interior surface of boot with Silicone Dielectric Compound WA-10, D7AZ-19A331-A (ESE-M1C171-A) or equivalent.
  1. Insert each wire on proper terminal of distributor cap. Ensure wires are all the way down over their terminals. The No. 1 terminal is identified on cap. Install wires starting with No. 1 terminal.
  1. Remove wire retaining brackets from old high tension wire set and install them on new set in same relative position. Install wires in brackets on valve rocker arm covers.
  1. Connect wires to proper spark plugs.
  1. Install coil wire.


Installation of distributor
Before installing distributor, visually inspect distributor. Inspect O-ring. It should fit tightly and be free of cuts. The drive gear should be free of nicks, cracks and excessive wear. Rotate distributor drive shaft. It should move freely, without binding.
  1. To install distributor correctly, No. 1 piston must be at Top Dead Center (TDC) of compression stroke. Remove No. 1 cylinder spark plug and rotate engine clockwise until No. 1 piston is on the compression stroke.
  1. With No. 1 piston on compression stroke, align timing pointer with TDC on the crankshaft damper.
  1. Align locating boss on rotor with hole on armature. Fully seat rotor on distributor shaft.
  1. Rotate distributor shaft so blade on rotor is pointing toward mark on distributor base, that was previously made in Step 2 of the Removal procedure.
  1. While installing distributor, continue rotating rotor slightly so leading edge of the vane is centered in vane switch stator assembly.
  1. Rotate distributor in block to align leading edge of vane and vane switch stator assembly. Verify rotor is pointing at No. 1 mark on distributor base. If vane and vane switch stator cannot be aligned by rotating distributor in cylinder block, remove distributor enough to just disengage distributor gear from camshaft gear. Rotate rotor enough to engage distributor gear on another tooth of camshaft gear. Repeat Step 1 if necessary.
  1. Install distributor hold-down clamp and bolt. Tighten bolt, but leave it loose enough to rotate distributor.
  1. Install distributor cap, No. 1 spark plug and ignition wires. Check that ignition wires are securely connected to the cap and spark plugs. Tighten distributor cap hold-down screws to 2.0-2.6 Nm (18-23 lb-in).
  1. Reconnect distributor to wiring harness.
  1. Set initial timing according to procedures found in Section 13A of the Powertrain Control/Emissions Diagnosis Manual .
  1. After timing is set, tighten distributor hold-down bolts to 23-34 Nm (17-25 lb-ft).
  1. Recheck initial timing. Adjust if necessary.

Oct 11, 2011 | 1992 Ford Tempo

1 Answer

REMOVE DISTRIBUTOR FOR A 1996 GMC JIMMY


Check this procedure...
  1. Disconnect the negative battery cable.
  2. If necessary, remove the air cleaner.
  3. Tag and remove the spark plug wires and the coil leads from the distributor.
  4. Unplug the electrical connector at the base of the distributor.
  5. Loosen the distributor cap fasteners and remove the cap.
  6. Using a marker, matchmark the rotor-to-housing and housing-to-engine block positions so that they can be matched during installation.
  7. Loosen and remove the distributor hold-down bolt.
  8. Remove the distributor from the engine.

INSTALLATION
Engine Not Disturbed
  1. Install the distributor in the engine making sure that the matchmarks are properly aligned.
  2. Install the hold-down bolt and tighten the bolt to 20 ft. lbs. (27 Nm).
  3. Install the distributor cap and attach the electrical connector at the base of the distributor.
  4. Install the spark plug wires and coil leads.
  5. If removed, install the air cleaner assembly.
  6. Connect the negative battery cable.
Engine Disturbed
(see Figure)
  1. Remove the No. 1 cylinder spark plug. Turn the engine using a socket wrench on the large bolt on the front of the crankshaft pulley. Place a finger near the No. 1 spark plug hole and turn the crankshaft until the piston reaches Top Dead Center (TDC). As the engine approaches TDC, you will feel air being expelled by the No. 1 cylinder. If the position is not being met, turn the engine another full turn (360 degree). Once the engine's position is correct, install the spark plug.
  2. Using a long screwdriver, align the oil pump drive shaft in the engine in the mating drive tab in the distributor.
  3. Install the distributor in the engine.
  4. Install the distributor in the engine making sure that the matchmarks are properly aligned.
  5. Install the hold-down bolt and tighten the bolt to 20 ft. lbs. (27 Nm).
  6. Install the distributor cap and attach the electrical connector at the base of the distributor.
  7. Install the spark plug wires and coil leads.
  8. If removed, install the air cleaner assembly.
  9. Connect the negative battery cable.
zjlimited_765.gif

Fig. : The rotor segment should be aligned with the pointer cast in the distributor base, when the distributor is fully seated



Hope this helps (remember to rating this free asnwer).

Oct 07, 2011 | 1996 GMC Jimmy

1 Answer

97 dodge stratus 2.5 car turns over but does not have spark. There is fuel. I replaced the ECM crankshaft position sensor.


I would start with the rotor and cap. I just worked on one and it was the distributor was bad.

If you need to remove it and rplace it heres how.

Distributor Removal and Installation REMOVAL
  1. Remove bolt holding air inlet resonator to intake manifold.
  2. Loosen clamps holding air cleaner cover to air cleaner housing.
  3. Remove PCV make-up air hose from air inlet tube.
  4. Loosen hose clamp at throttle body.
  5. Remove air inlet tube, resonator and air cleaner cover.
  6. Remove EGR tube.
  7. Remove spark plug cables from distributor cap.
  8. Loosen distributor cap hold-down screws and remove cap.
  9. Mark rotor position for installation reference, then remove rotor.
  10. Remove two harness connectors from distributor.
  11. Remove two sets of distributor hold-down nuts and washers from studs.
  12. Remove bolt and spark plug cable mounting bracket from top of distributor housing.
  13. Remove bolt and transaxle dipstick tube.
  14. Carefully remove distributor from engine.
INSTALLATION
  1. Install rotor on shaft.
  2. Position distributor in engine and ensure O-ring is properly seated on distributor. Replace O-ring if it is cracked or nicked.
  3. Carefully engage distributor drive with slotted end of camshaft. When the distributor is installed properly, the rotor will be in line with previously marked line on air intake plenum.
  4. If engine was cranked while distributor was removed, establish proper relationship between distributor shaft and No. 1 piston position as follows:
    1. Rotate crankshaft until number one piston is at top of compression stroke.
    2. Rotate rotor to No. 1 rotor terminal.
    3. Lower distributor into opening, engaging distributor drive with drive on camshaft. With distributor fully seated on engine, rotor should be under No. 1 terminal.
  1. Install distributor hold-down washers and nuts. Torque to 9 ft-lbs .
  2. Install spark plug cable bracket.
  3. Install two harness connectors to distributor.
  4. Install distributor cap.
  5. Install transaxle dipstick tube.
  6. Install EGR tube to intake manifold. Torque bolts to 8 ft-lbs .

Mar 06, 2011 | Dodge Stratus Cars & Trucks

1 Answer

Just wondering if you have a breakdown diagram for a 1992 dodge colt 1.5l distributer


I do not have a breakdown diagram for a distributor, but just the firing orders and description of ignition system for the Dodge Colt and related models (based on Chilton manuals) if that's what you're looking for: FIRING ORDERS Fig. 1: 1990 1.8L SOHC Engines Firing order: 1-3-4-2 Rotation: clockwise 84182009.gif

Fig. 2: 1.6L DOHC Engine Firing order: 1-3-4-2 Distributorless Ignition 84182010.gif

Fig. 3: 2.0L Engine Firing order: 1-3-4-2 Rotation: clockwise 84182011.gif

Fig. 4: 1.5L Engine Firing order: 1-3-4-2 Rotation: counterclockwise 84182012.gif

Fig. 5: 1993 1.8L Engine Firing order: 1-3-4-2 Rotation: counterclockwise 84182013.gif

Fig. 6: 2.4L Engine Firing order: 1-3-4-2 Rotation: clockwise 84182014.gif

To avoid confusion, replace spark plug wires one at a time. --- Distributor REMOVAL & INSTALLATION Although the distributor can be removed from the engine no matter which cylinder is about to fire, it is a good idea to have number one cylinder at TDC before distributor removal. 1.5L, 1.8L, 2.4L SOHC Engines
  1. Disconnect the negative battery cable.
  2. Disconnect and tag the spark plug wires from the distributor cap.
  3. Disconnect the distributor harness connector.
    Fig. 1: Ignition system for the 2.0L engine 84183001.gif

    Fig. 2: Ignition system for the 1.5L engine 84183002.gif

    Fig. 3: Ignition system for the 1992-93 1.8L engine 84183003.gif

    Fig. 4: Ignition system for the 2.4L engine 84183004.gif

  4. Loosen the distributor retaining bolt and remove the distributor from the engine. To install:
  5. Rotate the engine until No. 1 cylinder is at TDC on its compression stroke. NOTE: Be careful not to turn it to the No. 4 cylinder TDC on its compression stroke by mistake.
  6. Align the distributor housing and gear mating marks.
    Fig. 5: Ignition system for the 1990 1.8L engine 84183005.gif

    Fig. 6: Distributor installation for the 1990 1.8L engine 84183006.gif

    Fig. 7: Distributor installation for the 1992-93 1.8L engine 84183007.gif

  7. Install the distributor into the engine, while aligning the fine cut (groove or projection) on the distributor flange with the center of the distributor mounting stud.
  8. Install and tighten the distributor retaining bolt.
  9. Reconnect the distributor harness connector.
    Fig. 8: Distributor installation for the 2.4L engine 84183008.gif

    Fig. 9: Distributor installation for the 1.5L engine 84183009.gif

    Fig. 10: Distributor installation for the 2.0L engine 84183010.gif

  10. Install the distributor cap and spark plug wires.
  11. Reconnect the negative battery cable.
prev.gif next.gif prev.gif next.gif

Oct 11, 2010 | 1992 Dodge Colt

1 Answer

Turns over but dont start. 98 chevy blazer


First verify if you have spark using a tester,then verify you have fuel
now verify timing heres how;

To get #1 compression remove plug and put your finger in the hole and have someone crank the engine until you feel your finger being pushed off by the air pressure. Now line up the timing mark.

Rotate the number 1 cylinder to Top Dead Center (TDC) of the compression stroke.



Align white paint mark on the bottom stem of the distributor, and the pre-drilled indent hole in the bottom of the gear (3).
Notice: The ignition system distributor driven gear and rotor may be installed in multiple positions. In order to avoid mistakes, mark the distributor on the following components in order to ensure the same mounting position upon reassembly:

• The distributor driven gear

• The distributor shaft

• The rotor holes

Installing the driven gear 180 degrees out of alignment, or locating the rotor in the wrong holes, will cause a no-start condition. Premature engine wear or damage may result.

Notice: Installing the driven gear 180 degrees out of alignment, or locating the distributor rotor in the wrong holes, may cause a no-start condition. Premature engine wear and damage may result.

With the gear in this position, the rotor segment should be positioned as shown for a V6 engine (1) or V8 engine (2).
- The alignment will not be exact.

- If the driven gear is installed incorrectly, the dimple will be approximately 180 degrees opposite of the rotor segment when it is installed in the distributor.





Using a long screw driver, align the oil pump drive shaft to the drive tab of the distributor.
Guide the distributor into the engine. Ensure that the spark plug towers are perpendicular to the centerline of the engine.



Once the distributor is fully seated, the rotor segment should be aligned with the pointer cast into the distributor base.
- This pointer may have a 6 cast into it, indicating that the distributor is to be used on a 6 cylinder engine or a 8 cast into it, indicating that the distributor is to be used on a 8 cylinder engine.

- If the rotor segment does not come within a few degrees of the pointer, the gear mesh between the distributor and the camshaft may be off a tooth or more.

- If this is the case, repeat the procedure again in order to achieve proper alignment.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the distributor mounting clamp.

Tighten
Tighten the distributor clamp bolt to 25 N·m (18 lb ft).





Install the distributor cap.
Install two NEW distributor cap screws.

Tighten
Tighten the screws to 2.4 N·m (21 lb in).

Install the electrical connector to the distributor.
Install the spark plug wires to the distributor cap. Refer to Spark Plug Wire Harness Replacement
Important: If the Malfunction Indicator lamp is turned on after installing the distributor, and a DTC P1345 is found, the distributor has been installed incorrectly.
Repeat Installation Procedure 2 for proper distributor installation 
hope this helps

Jul 16, 2010 | 1998 Chevrolet Blazer

1 Answer

How do you change the distributor on a 1997 Nissan pick-up?


  1. Remove the two (2) screws securing the distributor cap and remove the cap.
  2. Remove the bolt securing the distributor.
  3. Disconnect the crank angle sensor connector and remove the distributor.
  4. 42331566
  1. Install the distributor, making sure the rotor is aligned as shown when fully seated.
  2. Install the distributor securing bolt and tighten slightly.
  3. Connect the crank angle sensor terminal.
  4. Install the distributor cap and tighten the screws

Jul 02, 2010 | 1997 Nissan Pickup

1 Answer

How do you replace the distributor on an 89 jeep wrangler YJ


Jeep Wrangler/YJ 1987-1995 Repair Guide

DISTRIBUITOR

REMOVAL & INSTALLATION

2.5L Engine
1987-90 VEHICLES
See Figures 1, 2, 3 and 4

5686591.gif


Fig. 1: Exploded view of the distributor-1987-90 2.5L engine


0d487c5.gif



Fig. 2: Positioning the oil pump shaft for distributor installation-1987-90 2.5L engine


506ca58.gif



Fig. 3: Positioning the distributor rotor and shaft for installation-1987-90 2.5L engine


85b810b.gif





Fig. 4: Rotor position with the distributor properly installed-1987-90 2.5L engine




  1. Disconnect the negative battery cable.
  2. Remove the primary lead from the terminal post at the side of the distributor.

The wire connector will contain a special conductive grease. Do not remove it. The same grease will also be found on the metal parts of the rotor.
  1. Disconnect the vacuum line if there is one.
  2. Remove the two distributor cap retaining hooks or screws and remove the distributor cap.
  3. Note the position of the rotor in relation to the base. Scribe a mark on the base of the distributor and on the engine block to facilitate reinstallation. Align the marks with the direction the metal tip of the rotor is pointing.
  4. Remove the bolt that holds the distributor to the engine.
  5. Lift the distributor assembly from the engine.

To install, if engine was not disturbed:
  1. Insert the distributor shaft and assembly into the engine. Line up the mark on the distributor and the one on the engine with the metal tip of the rotor. Make sure that the vacuum advance diaphragm is pointed in the same direction as it was pointed originally. This will be done automatically if the marks on the engine and the distributor are line up with the rotor.
  2. Install the distributor hold-down bolt and clamp. Leave the screw loose enough so that you can move the distributor with heavy hand pressure.
  3. Connect the primary wire to the distributor side of the coil. Install the distributor cap on the distributor housing. Secure the distributor cap with the spring clips or the screw type retainers, whichever is used.
  4. Install the spark plug wires. Make sure that the wires are pressed all of the way into the top of the distributor cap and firmly onto the spark plugs.

If the engine was turned while the distributor was removed, or if the marks were not drawn, it will be necessary to initially time the engine. Follow the procedure below.
To install, if engine was disturbed:
  1. Rotate the engine until the No.1 piston is at TDC compression.
  2. Using a flat bladed screwdriver, in the distributor hole, rotate the oil pump gear so that the slot in the oil pump shaft is slightly past the 3:00 o'clock position, relative to the length of the engine block.
  3. With the distributor cap removed, install the distributor with the rotor at the 5:00 o'clock position, relative to the oil pump gear shaft slot. When the distributor is completely in place, the rotor should be at the 6:00 o'clock position. If not, remove the distributor and perform the entire procedure again.
  4. Tighten the lockbolt.



Remember rated this post; I hope help you with this.










Aug 21, 2009 | 1989 Jeep Wrangler

1 Answer

I dont know how to put my spark plug wires in my car


firing order 1-4-2-5-3-6

  1. Insert each ignition wire on proper terminal of distributor cap . Ensure ignition wires are properly seated on the terminals. The No. 1 terminal is identified on distributor cap .
not sure if #1 cylinder is on the front right or front left. Call a dealer.
d8a0dc7.gif
Installation
Before installing distributor , visually inspect distributor . Inspect the O-ring. It should fit tightly and be free of cuts. The drive gear should be free of nicks, cracks and excessive wear. Rotate distributor drive shaft. It should move freely, without binding.
  1. To install distributor correctly, No. 1 piston (6108) must be at Top Dead Center (TDC) of compression stroke. Remove No. 1 cylinder spark plug (12405) and rotate crankshaft (6303) clockwise until No. 1 piston is on the compression stroke.
  1. With No. 1 piston on compression stroke, align timing pointer with TDC on the crankshaft damper.
  1. Align locating boss on distributor rotor with hole on armature. Fully seat distributor rotor on distributor shaft.
  1. Rotate distributor shaft so blade on distributor rotor is pointing toward mark on distributor base that was previously made in Step 2 of the Removal procedure.
  1. While installing, continue rotating distributor rotor slightly so leading edge of the vane is centered in vane switch stator assembly.
  1. Rotate distributor in engine front cover to align leading edge of vane and vane switch stator assembly. Verify distributor rotor is pointing at No. 1 mark on distributor base. If vane and vane switch stator cannot be aligned by rotating distributor in engine front cover , remove distributor enough to just disengage distributor gear from camshaft gear. Rotate distributor rotor enough to engage distributor gear on another tooth of camshaft gear. Repeat Step 1 if necessary.
  1. Install distributor hold-down clamp and bolt. Tighten bolt, but leave it loose enough to rotate distributor .
  1. Install distributor cap , No. 1 spark plug and ignition wires. Check that ignition wires are securely connected to the distributor cap and spark plugs . Tighten distributor cap hold-down screws to 2.0-2.6 Nm (18-23 lb-in).
  1. Reconnect distributor to engine control sensor wiring .
  1. Set initial engine ignition timing according to procedures found in Section 8A of the Powertrain Control/Emissions Diagnosis Manual.
  1. After engine ignition timing is set, tighten distributor hold-down bolt on to 20-30 Nm (15-22 lb-ft).
  1. Recheck initial engine ignition timing. Adjust if necessary.

Apr 09, 2009 | 1993 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...