Question about 1998 Jaguar XJ8L

Open Question

REMOVING ABS RING FRONT WHEEL

HOW TO REMOVE ABS RING XJ8

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2005 SATURN VUE ABS, AWD, R/FRONT BEARING REPLACEMENT

just did one today. removed housing from car, and used a press . be careful of aluminum housing. also used penatrating spray. clean oxidation from inside bearing hole,then lubricating, helped in installation

Posted on Dec 28, 2008

Ad
emissionwiz
  • 76109 Answers

SOURCE: 1998 Jaguar XJ8 front wheel bearing

it does press out/in, but they can get stuck. u are using a hydraulic bearing press?

Posted on Mar 20, 2009

bunnydawg
  • 5158 Answers

SOURCE: ABS warning light on permanently

check for cracks in the ring that the sensor reads off of... for the life of me i can't think of the proper name at the moment

Robert

Posted on May 27, 2009

  • 651 Answers

SOURCE: removing fwd passenger side wheel bearing

to detailed to try to explain. best thing to do is buy a haynes auto manual from local autoparts store 17$ it will give you step by step instructions.

Posted on Aug 04, 2009

c17hydro
  • 2984 Answers

SOURCE: How do you remove the front wheel hub?

Hope this diagram helps:

Exploded view of the steering knuckle and hub assembly


f891ebe.gif

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the abs ring on 1998 xj8


if it is a front ring remove front vertical link , you will see a spring locking device remove this a special tool is then needed to unscrew the abs ring if this is not availiable you try heating up the ring and using a drift, or drill down the side of the ring and splitting it with small chisel but you will need the special tool to fit the new one, they are TIGHTas they retain the hub bearing. if it is a rear one remove the rear hub carrier making sure you mark the track adjustment bolt to maintain rear wheel track. you should then be able to carefully remove the abs ring as it only trapped by the drive shaft, renew the hub nut

Mar 30, 2013 | 1998 Jaguar XJ8L

1 Answer

How to replace a wheel speed sensor


if abs [also speed] sensor is damaged better off replacing hub most sensors are incorporated into the hub or are a ring style that is a press fit around the hub and still have to remove hub to replace--- larger vehicles and some cross overs u can remove just the sensor not in your case --if just wire damaged can order and replace but if abs needs to be replaced than prior to removing wheel loosen center axle nut dont remove yet jack up and support vehicle- remove wheel,brake caliper,brake bracket,rotor and center axle nut ,disconnect abs wire connection and remove the 3 bolts at rear of hub and remove hub from spindle clean area and reinstall hub careful of wire connection replace all components

May 14, 2012 | 2006 Buick Terraza

1 Answer

Change front brakesensor saab 9-5


Step 1 - First, you must locate the malfunctioning wheel sensor. This is done by using a scan tool or multi-meter. Plug in an ABS scan tool and follow the prompts to retrieve the trouble code associated with a failed wheel speed sensor.

Step 2 - If a scan tool is not available you can use a voltage multi meter. Disconnect the wiring connector at each wheel. Next attach the meter leads to each of the ABS connector terminals that lead to the wheel sensor being tested.

Step 3 - Once the failed wheel sensor has being discovered remove the sensor mounting bolts, or remove the tire and bearing hub. (Some ABS wheel sensors are intergraded into the wheel bearing hub)

Step 4 - Next, Inspect the sensor stator ring to confirm that there is no damage existing to the ring. If the ring shows signs or damage replacement is required.

Step 5 - Then, reinstall the new sensor or wheel bearing hub and reassemble.

Step 6 - Reconnect the electrical connector.
Once the new sensor is installed the system should run tests confirming is operating normally. At this point the warning light will go out. Some systems might require a ABS scan tool to reset the system, but this not typical.

Mar 24, 2012 | Cars & Trucks

1 Answer

How to clean wheel sensor jaguar xj8


This all depends on if it is a wheel sensor. you will need to locate the sensor which is one on each wheel, remove the sensor and just clean off. reinstall sensor.
The best thing to do is have the computer scanned to see what code is stored, the code will tell you what the problem may be. For example if there is a code that reads left front speed sensor signal loss. then you would check that sensor and the connector to sensor, you would also look at abs tone ring. the tone ring is the ring that the sensor ride over.
I am not sure if the ring is external, you will need to look and see, cleaning the ring is a good idea also. good day.

Mar 06, 2012 | Jaguar XJ8 Cars & Trucks

1 Answer

Need instructions on installing an indicator #7l2z2c182a for 2006 Ford Explorer


SECTION 206-09: Vehicle Dynamic Systems 2006 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/03/2007 Wheel Speed Sensor Ring - Rear adobe.gif Printable View (134 KB)
Special Tool(s) st2132a.jpg Installer, Wheel Speed Sensor Ring
206-084/1 st1515a.jpg Installer, Wheel Speed Sensor Ring
206-084/2
n0078683.jpg
Item Part Number Description 1 2C182 Wheel speed sensor ring 2 4K138 Halfshaft Removal
  1. Remove the rear halfshaft. For additional information, refer to Section 205-05.
  1. Using a suitable driver, remove the ABS wheel speed sensor ring.
Installation
  1. Install the new ABS wheel speed sensor and the Wheel Speed Sensor Ring Installers on the halfshaft as shown.
    n0078685.jpg
  1. Using the Wheel Speed Sensor Ring Installers, install the ABS wheel speed sensor ring as shown.
    n0078686.jpg
    n0078691.jpg

Sep 28, 2011 | 2006 Ford Explorer

1 Answer

Abs activates just before truck stops (2005 chevy silverado) wheels not skidding, assuming a wheel sensor is bad, how do find out which one, or is the problem in the abs computer, abs light does not come...


This is a condition known as over active ABS. GM has a technical service bulletin for this. Basically what it say is to remove the front wheel speed sensors from the hubs, clean the mating surface between the sensor and the hub, apply some di-electric grease over the cleaned area, and reinstall the sensor.

You can try this on the front sensors and see if the problem goes away. I will warn you that you need to be very careful removing the sensor from the hub as they can break off. If it breaks off in the hub you will need to replace the hub and bearing.

You can also check to see if one of the front wheel bearings is loose. with the tire off the ground grab the tire at the 12 and 6 position and push/pull. if the wheel moves and you can see the rotor moving also than the wheel bearing may be sloppy enough for internal exciter ring to get an excessive gap from the abs sensor.

The easiest thing to do is look at wheel speed data on a higher end scan tool. When the symptom happens you will see the wheel speed drop out. Whatever wheel drops out is the wheel that needs to be checked.

Hope that helps.

Oct 01, 2010 | 2005 Chevrolet Silverado

1 Answer

How to replace a Jaguar X Type fron wheel bearing


Jaguar 2000-06

Wheel Bearings
Removal & Installation
  1. Remove the brake disc.
  2. Remove and discard the retaining clip. Detach the ABS sensor.
  3. Remove and discard the O-ring seal.
  4. Remove the wheel hub and bearing retaining bolts.
  5. Remove the wheel hub and bearing.
  6. Prior to applying sealer, clean the ABS sensor sealing surface and the ABS sensor aperture sealing surface.
  7. Install a new O-ring seal.
  8. Apply a 2.5mm bead of Loctite Ultra Blue 587 Silicone (RTV) sealer to the ABS sensor sealing surface.
  9. Install a new ABS sensor retaining clip.
  10. Install the hub/bearing assembly. Tighten to 90 Nm.

  1. Remove wheel knuckle.
NOTE When removing the wheel hub from the wheel knuckle the bearing will be destroyed and the bearing inner ring will remain on the wheel hub.
d752c5a.jpg

Fig. Using special tools, remove the wheel hub-X-Type
  1. Using special tools, remove the wheel hub.
  2. Using a suitable tool, remove the bearing inner ring.
  3. Using special tools, remove the wheel bearing.
  4. 2125147.jpg

    Fig. Using a suitable tool, remove the bearing inner ring-X-Type

    ee51ce7.jpg

    Fig. Using special tools, remove the wheel bearing-X-Type

To install:

b506586.jpg

Fig. Insert special tool 204-312 in to 204-309-X-Type
  1. Insert special tool 204-312 in to 204-309.
  2. Support the wheel knuckle on special tools.
NOTE Make sure wheel bearing is correctly orientated with the colored side facing inboard.
  1. Align the bearing over special tool.
  2. Using special tools, press bearing into wheel knuckle.
  3. Change special tool 204-312 to 204-313.
  4. Align the bearing and wheel knuckle over special tool.
  5. Slide wheel hub over the guide and align to the bearing.
  6. Using special tools install the wheel hub.
  7. Install the wheel knuckle.

  8. 5a457fa.jpg

    Fig. Using special tools, press bearing into wheel knuckle-X-Type

    b9fcc3f.jpg

    Fig. Change special tool 204-312 to 204-313-X-Type

    be319f2.jpg

    Fig. Align the bearing and wheel knuckle over special tool-X-Type

    8a9e0dc.jpg

    Fig. Slide wheel hub over the guide and align to the bearing-X-Type
  1. Raise front of vehicle and support on stands.
  2. Remove appropriate road wheel.
  3. Using wire or string, secure brake caliper to road spring to take weight off brake hose.
  4. Raise vehicle sufficient to provide access for special tool 204-111.
  5. Install special tool 204-111 in road spring.
  6. Slacken tool adjuster to suit spring length.
  7. Install adaptor and thrust collar.
  8. Position stem of tool in center of spring passing dowel through slot in suspension turret.
  9. 24ce878.jpg

    Fig. Install special tool 204-111 in road spring-XJ Range and XK Range

    1d0063e.jpg

    Fig. Position stem of tool in center of spring passing dowel through slot in suspension turret-XJ Range and XK Range

NOTE When turning tool adjuster, ensure that tool stem does not rotate and disturb position of dowel in suspension turret.
  1. Engage dowel of special tool 204-111 in suspension turret and rotate to position across slot.
  2. Lower vehicle onto stands.
  3. Rotate tool adjuster to tension spring.
  4. Remove wheel speed sensor securing screw and withdraw sensor from vertical link.
  5. Remove nut securing tie rod outer ball joint to steering arm.
  6. Release ball joint from vertical link.
  7. Install special tool 211-098 on tie rod outer ball joint.
  8. Tighten tool bolt to release taper pin from vertical link.
  9. Remove special tool from ball joint and position tie rod for access.
  10. Remove nut securing upper control arm ball joint to vertical link.

  11. 3af9a83.jpg

    Fig. Install special tool 211-098 on tie rod outer ball joint-XJ Range and XK Range

continue...

Aug 03, 2010 | 2002 Jaguar X-Type

1 Answer

I have a 1998 jaguar xj8 i changed the steering wheel knuckle abs ring break pads caliper and now the abs sign is on?


Did you turn the key on at any time when the wheelspeed sensor (this is what detects the rotation of the "ABS ring") was disconnected? You may have to interrogate the ABS controller with a diagnostic computer to read the diagnostic trouble codes and then clear them. Also, you may have to drive the car 10km per hour for a few moments after the codes are cleared to get the light to go out.

Feb 26, 2010 | 1998 Jaguar XK8

1 Answer

2001 silverado 4x4 abs brake keeps coming on


in these trucks if the front abs activates at low speeds it is normally because of the wheel speed sensors in the front hubs. easy fix is to remove wheel speed sensor from wheel bearing. clean and file cast surface of bearing to allow sensor to move closer to internal reluctor ring. what happens is over time the casting rusts and creates a larger gap. please rate if this works.

Dec 04, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
1998 Jaguar XJ8L Logo

Related Topics:

512 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...