Question about 2001 GMC Yukon XL
Most parts stores dont sell metal fuel lines that long.. you can use metal brake lines though(same thing) these are different diameters so you need to take samples in to insure the right sizes are given to you..make sure to get longer than you measure by at least one foot measure carefully..
Posted on Jan 02, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
First remove the cap off the master cylinder. Push in the piston on one caliper with a c clamp, or pry it back between the pad and rotor with a prybar. Then remove the 2 bolts on the caliper itself. Replace pads.Go to other side, repeat sequence
Posted on Dec 11, 2008
SOURCE: light replacement
Just reach behind the bumper and grab the light/electrical harness and twist is either way and then it should pull out put in a new 194 bulb and you are set.
Posted on Jan 08, 2009
Changing the oil pan gasket on a GMC Yukon XL is realtively simple, but does require removal of the exhaust pipe. You will need a new oil pan gasket and a new exhaust pipe flange gasket.
Put the car on ramps or jacks to access the undercarriage.
Remove the exhaust pipe by removing the 3 nuts holding the exhaust pipe flange to the exhaust manifold. These nuts often rust and prior application of penetrating oil may be required to remove them without damage. Once the pipe is unbolted, work the exhaust system loose from the hanging brackets. In most cases the entire system does not have to be removed since there is enough room to remove the pan with only the front hangers removed.
Drain the oil from the engine
Remove the 10 mm bolts holding the pan to the block.
Remove the old gasket material and scrape any remaining gasket from the block and pan.
Install the new gasket. Forma-Gasket or a similar product may be used in small quantities to "glue" the new gasket in place and prevent shifting while the pan is reattached to the block.
Reinsall the 10 mm bolts in a cross pattern to ensure the gasket is compressed evenly. Do not overtighten the bolts.
Replace the pipe to flange gasket between the exhaust pipe and the exhaust manifold with a new part.
Reattach the exhuast pipe to the hangers.
Install the 3 bolts connecting the pipe flange to the exhaust manifold.
Fill the engine with oil.
Posted on Sep 15, 2009
Your sending unit for the guage is part of your fuel pump in the tank. But first try your fuel pump relay, may be working intermittenly when you hit a bump or something. Or possibly a loose wire somewhere along the way. Much less expensive (worth a look).
Posted on Dec 18, 2009
turn key to on position, pump gas pedal to floor 5 times and turn off key. start vehilce. Change oil light should flash for 7 seconds and then go out.
Posted on May 26, 2010
Tips for a great answer:
Nov 28, 2011 | 2001 GMC Yukon XL
Jul 07, 2011 | 2001 GMC Yukon XL
Feb 27, 2011 | 2001 GMC Yukon XL
May 09, 2010 | 2001 GMC Yukon XL
Feb 12, 2010 | 2002 GMC Yukon XL
Aug 07, 2009 | 2001 GMC Yukon XL
Aug 01, 2009 | 2001 GMC Yukon
Jul 06, 2009 | 2001 GMC Yukon XL
56 people viewed this question
Usually answered in minutes!