Question about 2003 Toyota Tundra
The 4wd light does not blink, it just stays on and I can not take it off of 4wd. Any recommendations as to how to disengage it myself? I can't really afford to pay a mechanic to do the work for me.
Try unplugging the 4wheel drive actuator and see if it will disingage; if that doesnt work then its probably in the transfer case itself.
Posted on Jan 01, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2003 Toyota Sequoia 4WD
i have a 2003 sequoia ltd and i can tell you that the virtual traction control lights will come on after ignition and remain on as a result of anything that has affected your vehicle operation. from sensors to seals, the computer is designed to shut down the traction control if it has determined that any part of the engine/mechanical systems has malfunctioned. first it was the abs had to be reset after i slammed my brakes on. next i needed a new fuel/oxygen sensor, the passenger primary, and after having fixed both the traction control operates properly, lights go off after ignition and stay off. i think the vehicle operates more driver friendly when its off, because it doesn't go off every time one of the wheels slips. i expect it will happen next time something else malfunctions, its toyotas way of annoying you into their service shop. go to a tune-up shop, (minitune) instead they'll tell you whats wrong and it'll be cheaper.
Posted on Jan 08, 2009
Your power door locke solenoid is seized. You will need to replace it. You are going to have to get the entire door panel off, and then reach in to manually pull the solenoid arm to retract the lock mechanism. Then the door will open.
Posted on Mar 06, 2009
Remove the two screws holding the tail light cover in place along the edge of the tail light assembly.
After you remove the two screws in the back panel, you have to pull the assembly out towards the side of the vehicle. You cannot pull it straight back from the trunk or you will break the pins that hold the lens cover onto the side of the SUV.
There are two pins that allow the light cover to be secured against the back of the truck. One pin is towards the top, the other pin is towards the bottom.
Twist out the bulb assembly.
Pull out the bulb
Insert the new bulb
Twist back in the bulb assembly
Place the pins over the pin holes in the light cover mold on the side of the truck
Push in gently Replace screws and you are done.
Posted on Nov 02, 2009
sounds like park safety switch,there are 2 switches 1 neutral and 1 park, if it starts in neutral,it is working,if in park,and does not start usually means bad switch or wire off.
Posted on Dec 23, 2009
You have to use a scanner and pull the code out that is causing the check engine light to come on. whatever code/codes you find are probably related to vsc light.
Good luck and keep me posted
Posted on Mar 09, 2010
Tips for a great answer:
Sep 30, 2015 | Cars & Trucks
Feb 01, 2015 | 2001 Toyota Sequoia
Dec 09, 2013 | 2001 Toyota Sequoia
Jan 21, 2011 | 2001 Toyota Sequoia
Dec 19, 2010 | 2004 Toyota Sequoia
Aug 30, 2010 | 2001 Toyota Sequoia
Jan 07, 2010 | 2001 Toyota Sequoia
Nov 12, 2009 | 2001 Toyota Sequoia
Sep 11, 2008 | 2003 Toyota Sequoia
182 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: