Question about 2003 Nissan Murano

Open Question

How to install a blower motor - 2003 Nissan Murano

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to change fan on blower heater


Removal

  1. Remove wiper arms.
  2. Remove cowl panel.
  3. Disconnect blower motor electrical connector and vent tube.
  4. Remove blower motor retaining screws.


  1. Remove fan retaining nut from blower shaft through plenum opening while holding the fan from the engine compartment.
  2. Remove fan from blower motor while removing blower motor from vehicle.
Installation

  1. Hold fan through plenum opening.
  2. Install blower motor to vehicle while installing fan to blower motor.
  3. Install fan retaining nut to blower motor shaft through plenum opening.
  4. Install blower motor retaining screws.
  5. Connect electrical connector and vent tube.
  6. Install cowl panel.
  7. Install wiper arms.

Aug 13, 2013 | 1991 Oldsmobile Cutlass Ciera

1 Answer

The heater blower stopped working and the fuse is not blown?


Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.
  5. Disconnect the electrical connector from the blower motor.
  6. Remove the blower motor mounting bolts.
  7. Remove the blower motor insulating cover.
  8. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the electrical connector to the blower motor.
  4. Connect the cooling tube to the blower motor.
  5. Install the rear coolant recovery reservoir mounting stud.
  6. Install the coolant reservoir.
  7. Install the PCM.
W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Move the PCM connectors out of the way.
  6. Remove the blower motor access cover screws. CAUTION
    Do not cut any deeper than necessary in order to remove the access cover.
  7. Cut through the access cover on the cut line using a sharp utility knife.
  8. Disconnect the cooling tube from the blower motor.
  9. Remove the blower motor mounting bolts.
  10. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the cooling tube to the blower motor.
  4. Install the blower motor access cover.
  5. Install the blower motor access cover retaining screws.
  6. Using black weather-strip adhesive, seal the cut line.
  7. Connect the blower motor electrical connector.
  8. Reposition the PCM connectors.
  9. Install the rear coolant recovery reservoir mounting stud.
  10. Install the coolant reservoir.
  11. Install the PCM.
prev.gif next.gif

Feb 08, 2011 | 1996 Chevrolet Blazer

1 Answer

How to remove blower motor


Try this procedure...

1. Disconnect the negative battery cable.
2. Remove the instrument panel (IP) storage compartment.
3. Remove the front screw from the right door sill plate.
4. Remove the right hinge pillar trim plate.
5. Disconnect the electrical connectors from the blower motor, as necessary.
6. Remove the bolt from the right lower IP support.
7. Remove the blower motor cover.
8. Remove the motor cooling tube.
9. Remove the blower motor flange screws and ferrules.
10. Perform the following steps in order to remove the blower motor:
Carefully pull the blower motor forward in order to avoid distorting the blower motor fan.
If necessary, pry back the right side of the IP.

11. Inspect the blower motor terminals for distortion.
12. Clean corrosion from the terminals as necessary.
13. Replace the blower motor as necessary.
14. Inspect the flange of the blower motor for damage or distortion that may cause an air leak.
15. Repair the flange as necessary.
16. Inspect the blower fan for any damage and distortion.

zjlimited_239.jpg

Fig. Pull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor

To install:

1. Guide the blower motor and blower fan into position. Be careful in order not to catch the blower fan on any protruding components.
2. Install the blower motor flange ferrules and screws. Tighten the blower motor mounting screws to 20 inch lbs. (2.1 Nm).
3. Install the blower motor cooling tube.
4. Install the blower motor cover.
5. Install the bolt to the right lower IP support.
6. Install the electrical connectors to the blower motor, as necessary.
7. Install the right hinge pillar trim panel.
8. Install the front screw into the door sill plate.
9. Install the instrument panel storage compartment.
10. Install the negative battery cable.
11. Verify the circuit operation.


Hope helps.

Dec 14, 2010 | 1999 GMC Yukon Denali

1 Answer

How to change blowermotor on 2001 gmc jimmy


Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.
  5. Disconnect the electrical connector from the blower motor.
  6. Remove the blower motor mounting bolts.
  7. Remove the blower motor insulating cover.
  8. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the electrical connector to the blower motor.
  4. Connect the cooling tube to the blower motor.
  5. Install the rear coolant recovery reservoir mounting stud.
  6. Install the coolant reservoir.
  7. Install the PCM.
W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Move the PCM connectors out of the way.
  6. Remove the blower motor access cover screws. CAUTION
    Do not cut any deeper than necessary in order to remove the access cover.
  7. Cut through the access cover on the cut line using a sharp utility knife.
  8. Disconnect the cooling tube from the blower motor.
  9. Remove the blower motor mounting bolts.
  10. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the cooling tube to the blower motor.
  4. Install the blower motor access cover.
  5. Install the blower motor access cover retaining screws.
  6. Using black weather-strip adhesive, seal the cut line.
  7. Connect the blower motor electrical connector.
  8. Reposition the PCM connectors.
  9. Install the rear coolant recovery reservoir mounting stud.
  10. Install the coolant reservoir.
  11. Install the PCM.
prev.gif next.gif

Dec 08, 2010 | 2001 GMC Jimmy

1 Answer

Need to replace heater blower motor. How do I get to it?


Behind the glove box. Please see my tip at http://www.fixya.com/cars/r6234839-doesn_t_heater_or_air_conditioner_blow . These are generic instructions. If you get stuck, please get back to me.

See instructions from autozone.com below.


REMOVAL & INSTALLATION


With Air Conditioning
See Figures 1, 2 and 3

  1. Disconnect the negative battery cable.
  2. Remove the glove compartment door and glove compartment.
  3. Disconnect the blower motor wires from the blower motor resistor.

jturcotte_62.gif
Fig. Fig. 1: Disconnect the blower motor wires from the blower motor resistor-1988 Escort
  1. Loosen the instrument panel at the lower right-hand side prior to removing the motor through the glove compartment opening.
  2. Remove the blower motor and mounting plate from the evaporator case.
  3. Rotate the motor until the mounting plate flat clears the edge of the glove compartment opening and remove the motor.
  4. Remove the hub clamp spring from the blower wheel hub. Then remove the blower wheel from the motor shaft.
jturcotte_63.gif
Fig. Fig. 2: Unbolt the mounting plate from the case


jturcotte_64.gif

Fig. Fig. 3: The motor can now be removed from the case


To install:

  1. If removed, assemble the blower wheel to the motor shaft and install the hub clamp.
  2. Install the motor and blower wheel assembly.
  3. Secure the instrument panel at the lower right-hand side.
  4. Connect the blower motor wires at the blower motor resistor.
  5. Install the glove compartment door and the glove compartment.
  6. Connect the negative battery cable.
  7. Check the system for proper operation.

Without Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the air inlet duct assembly.
  3. Remove the hub clamp spring from the blower wheel hub. Pull the blower wheel from the blower motor shaft.
  4. Remove the blower motor flange attaching screws located inside the blower housing.
  5. Pull the blower motor out from the blower housing (heater case) and disconnect the blower motor wires from the motor.

To install:

  1. Connect the wires to the blower motor and position the motor in the blower housing.
  2. Install the blower motor attaching screws.
  3. Position the blower wheel on the motor shaft and install the hub clamp spring.
  4. Install the air inlet duct assembly and the right ventilator assembly.
  5. Connect negative battery cable.
  6. Check the system for proper operation.

Nov 05, 2010 | 1989 Ford Escort

1 Answer

How to replace a blower motor in a 1996 ford thunderbird lx


Removal
  1. Remove the glove compartment liner to gain access to the heater blower motor and blower motor wheel assembly mounting screws.
  1. Use a small screwdriver to remove clip retaining hydraulic damper strut.
  1. Remove four screws and remove the heater blower motor assembly and blower motor wheel assembly from the heater blower motor housing.
Installation
  1. Using a new seal, position the heater blower motor and blower motor wheel assembly to the heater blower motor housing with the flat side of the flange near the heater blower motor switch resistor (18591). Install the four retaining screws.
  1. Tape the heater blower motor power lead to the air inlet duct to keep the wire away from the blower outlet during installation.
  1. Install the heater blower motor and blower motor wheel assembly in the vehicle.
  1. Install the glove compartment liner.

Oct 07, 2010 | 1996 Ford Thunderbird LX

1 Answer

Blower motor replacement


Very easy!!!

Here ya go!!!

Removal & Installation
  1. Remove the right side sound insulator in the passenger compartment.
  2. Disconnect the electrical connector from the blower motor.
  3. Disconnect the blower ventilation tube from the module.
  4. Remove the blower motor screws.
  5. Remove the blower motor from the housing.
  6. Install the blower motor into the housing.
To install:
  1. Install the blower motor screws and tighten to 15 inch lbs. (1.5 Nm).
  2. Install the blower ventilation tube to the module.
  3. Connect the blower motor electrical connector.
  4. Install the right side sound insulator.

Jun 03, 2010 | 2004 Buick LeSabre

1 Answer

How to install a front blower motor in a 96 ford explorer


Blower Motor - REMOVAL & INSTALLATION
(see Figures 1 and 2)

8e5714d.jpg

Fig. 1: Exploded view of the blower motor mounting

ff3bdf8.jpg

Fig. 2: Exploded view of the blower motor and wheel (fan) assembly

Without Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the air cleaner or air inlet duct, as necessary.
  3. If necessary, Remove the speed control module and the washer fluid reservoir.

2587a00.jpg

Fig. 3: To remove the blower motor, first disconnect the electrical wire harness plug...

f234e79.jpg

Fig. 4: ...then remove the blower motor cooling tube from the motor
  1. Disconnect the wire harness connector from the blower motor by pushing down on the connector tabs and pulling the connector off of the motor.
  2. Disconnect the blower motor cooling tube at the blower motor.
3bbd0e1.jpg

Fig. 5: Remove the blower motor attaching screws and the washer fluid reservoir...

8da3ac1.jpg

Fig. 6: ...then slide the blower motor from the housing. Take care to not damage the blower wheel (arrow)
  1. Remove the 2 screws attaching the blower motor and wheel to the heater blower assembly.
  2. Holding the cooling tube aside, pull the blower motor and wheel from the heater blower assembly and remove it from the vehicle.
  3. Remove the blower wheel push-nut and/or clamp from the motor shaft and pull the blower wheel from the motor shaft.
To install:
  1. Install the blower wheel on the blower motor shaft.
  2. Install the hub clamp and/or push-nut.
  3. Holding the cooling tube aside, position the blower motor and wheel on the heater blower assembly and install the 2 attaching screws.
  4. Connect the blower motor cooling tube and the wire harness connector.
  5. Install the vacuum reservoir on the hoses with the 1 screws.
  6. If removed, install the speed control module and the washer fluid reservoir.
  7. Install the air cleaner or air inlet duct, as necessary.
  8. Connect the negative battery cable and check the system for proper operation.

With Air Conditioning
  1. Disconnect the negative battery cable.
  2. In the engine compartment, disconnect the wire harness from the motor by pushing down on the tab while pulling the connection off at the motor.
  3. Remove the air cleaner or air inlet duct, as necessary.
  4. If necessary, remove the solenoid box cover retaining bolts and the solenoid box cover.
  5. Disconnect the blower motor cooling tube from the blower motor.
  6. Remove the blower motor mounting plate attaching screws and remove the motor and wheel assembly from the evaporator assembly blower motor housing.
  7. Remove the blower motor hub clamp from the motor shaft and pull the blower wheel from the shaft.
To install:
  1. Install the blower motor wheel on the blower motor shaft and install a new hub clamp.
  2. Install a new motor mounting seal on the blower housing before installing the blower motor.
  3. Position the blower motor and wheel assembly in the blower housing and install the attaching screws.
  4. Connect the blower motor cooling tube.
  5. Connect the electrical wire harness hard shell connector to the blower motor by pushing into place.
  6. If removed, position the solenoid box cover into place and install the 2 retaining screws.
  7. Install the air cleaner or air inlet duct, as necessary.
  8. Connect the negative battery cable and check the blower motor in all speeds for proper operation.

Hope this help (remember comment and rated this).

Apr 23, 2010 | 1996 Ford Explorer

1 Answer

How to replace the blower motor fan assembly in a 2000 GMC Yukon XL K1500 4X4


Blower Motor Removal & Installation Delphi
Blower Motor Replacement (Delphi)

1fb4643.gif
To Remove:
  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor insulating cover screws.
  4. Remove the blower motor insulating cover.
  5. Pull the retaining tab down and rotate blower motor counterclockwise to remove.
To Install:

  1. Position the blower motor and turn assembly clockwise until tab locks in place.
  2. Install the blower motor insulating cover.
  3. Connect the electrical connector to the blower motor.
  4. Install the instrument panel sound insulator panel (if equipped).

Visteon

Blower Motor Replacement (Visteon)

878e8d8.gif
To Remove:
  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor screws.
  4. Remove the blower motor from the HVAC module.
To Install:
  1. Position the blower motor and install mounting screws.
  2. Connect the electrical connector to the blower motor.
  3. Install the instrument panel sound insulator panel (if equipped).

Oct 02, 2009 | 2000 GMC Yukon XL

Not finding what you are looking for?
2003 Nissan Murano Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...