Question about 2000 Mitsubishi Diamante

1 Answer

How to remove electrical starter for inspection from a sears snow thrower model 247.88955

How can I remove the electrical starter for inspection from Sears Snow Thrower Model 247.88955 ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 3,103 Answers

Wshat type of engine does it have.. briggs or tecomseh..

Posted on Jan 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove sears snow thrower starter


need to know which motor type it has..briggs or tekumseh

Jan 01, 2014 | Cars & Trucks

1 Answer

Where is the starter located at on the vehicle on my jeep ? I need to replace the starter right away.


It is bolted to the transmission bell housing.

Exploded view of the starter - 5.2L and 5.9L model shown

tecnovative_119.gif
These are the steps invovlved in replacing the starter.

  1. Disconnect the battery ground.
  2. Raise and support the vehicle on jackstands.
  3. On 1989-91 models equipped with a 2.5L engine, it is necessary to remove the exhaust clamp and bracket, and the transmission brace rod before removing the starter.
  4. Remove all wires from the starter and tag them for installation. NOTE: It may be easier to remove the solenoid wires after lowering the starter. Support the starter before removing the wires. DO NOT LET THE STARTER HANG BY THE WIRES.
  5. On 4.0L, 5.2L and 5.9L engines, it may be necessary to remove the oil cooler line bracket and the exhaust brace.
  6. Remove all but one attaching bolt, support the starter (it's heavier than it looks) and remove the last bolt.
  7. Lower the starter from the engine.
  8. If installing the original starter, inspect the pinion gear for damage or excessive wear.
  9. Inspect the flywheel gear teeth for damage through the starter mounting hole.
  10. Install the starter in the engine and hand-tighten the retaining bolts.
  11. Engage any electrical connections that were removed from the starter.
  12. Tighten the retaining bolts and engage any cooler lines, braces and brackets that were removed. Lower the vehicle.
  13. Connect the negative battery cable and check for proper starter operation.

Feb 11, 2011 | 1994 Jeep Grand Cherokee

2 Answers

How do I REPLACE A STATER


Please see my tip at http://www.fixya.com/cars/r5973094-starter_replace . If you get stuck, please get back to me. Exact procedure from autozone.com is pasted below.
a1163b0.gif

  1. Remove or disconnect the following:

    Negative battery cable Radiator air baffle, for clearance if necessary Flywheel inspection cover bolts Flywheel inspection cover Electrical connections from the starter motor Starter motor mounting bolts Starter motor
To install:
  1. Install or connect the following:
    NOTE Before installing the starter motor to the engine, tighten the nut next to the cap on the solenoid BAT terminal. If this terminal is not tight in the solenoid cap, the cap may be damaged during installation of electrical connections and cause the starter motor to fail later.

    Starter motor Starter motor mounting bolts and tighten the bolts to 30 ft. lbs. (40 Nm) Electrical connection to the battery terminal on the solenoid and tighten the battery terminal nut to 13 ft. lbs. (17 Nm) Electrical connections to the S terminal on the solenoid and tighten solenoid S terminal nut to 27 inch lbs. (3 Nm) Flywheel inspection cover Flywheel inspection cover bolts Radiator air baffle, if removed
  2. Connect the negative battery cable

Oct 19, 2010 | 2001 Oldsmobile Silhouette

2 Answers

How to remove starter


Removal & Installation - Starter
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle assembly
    Electrical connections Torque converter cover Starter
To install:
  1. Install or connect the following:
    Starter. Torque the bolts to 35 ft. lbs. (47 Nm). Torque converter cover Solenoid -BAT- terminal. Torque the nut to 89 inch lbs. (10 Nm). Solenoid -S- terminal. Torque the nut to 27 inch lbs. (3 Nm). Radiator air baffle assembly Negative battery cable
  2. Perform a charging system test and verify the starter is operating properly
8e0154d.jpg

Fig. Showing the starter motor location and electrical connections
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle, for clearance if necessary Flywheel inspection cover bolts Flywheel inspection cover Electrical connections from the starter motor Starter motor mounting bolts Starter motor
To install:
  1. Install or connect the following:
    NOTE Before installing the starter motor to the engine, tighten the nut next to the cap on the solenoid BAT terminal. If this terminal is not tight in the solenoid cap, the cap may be damaged during installation of electrical connections and cause the starter motor to fail later.

    Starter motor Starter motor mounting bolts and tighten the bolts to 30 ft. lbs. (40 Nm) Electrical connection to the battery terminal on the solenoid and tighten the battery terminal nut to 13 ft. lbs. (17 Nm) Electrical connections to the S terminal on the solenoid and tighten solenoid S terminal nut to 27 inch lbs. (3 Nm) Flywheel inspection cover Flywheel inspection cover bolts Radiator air baffle, if removed
  2. Connect the negative battery cable

Hope helps, remember rated this.

Aug 12, 2010 | 2001 Pontiac Montana

1 Answer

Where is the location of the starter on a 1999 bonneville se and is it hard to take off yourself?


REMOVAL & INSTALLATION
(see Figures 2, 3, 4, 5, 6 and 7)
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
b6fb00e.jpg

Fig. 2: Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion

9183313.jpg

Fig. 3: Exploded view of the starter motor electrical connections
  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
343c68b.jpg

Fig. 4: The starter is attached to the engine with 2 mounting bolts (see arrows)

32e179d.jpg

Fig. 5: Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation

3534611.jpg

Fig. 6: Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle


Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.

0694abc.jpg

Fig. 7: Exploded view of the starter motor mounting - 1987-97 vehicles


To install:
Note the location of any shims so they may be replaced in the same positions upon installation.
  1. Place the starter in position, then install the starter-to-engine bolts and tighten to 32 ft. lbs. (43 Nm).
  2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
    1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
    2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).
  3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
  4. If removed, install the splash shield.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Hope helps (remember rated and comment his).

Aug 06, 2010 | 1999 Pontiac Bonneville

1 Answer

How do i get the instructions on how to replace a starter for an 1989 pontiac bonneville


REMOVAL & INSTALLATION
(see Figures 2, 3, 4, 5, 6 and 7)
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
a20ef19.jpg

Fig. 2: Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion

6700461.jpg

Fig. 3: Exploded view of the starter motor electrical connections
  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
7369158.jpg

Fig. 4: The starter is attached to the engine with 2 mounting bolts (see arrows)

168c839.jpg

Fig. 5: Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation

3142660.jpg

Fig. 6: Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle

Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.

5e6998d.jpg

Fig. 7: Exploded view of the starter motor mounting - 1987-97 vehicles

To install:



Note the location of any shims so they may be replaced in the same positions upon installation.
  1. Place the starter in position, then install the starter-to-engine bolts and tighten to 32 ft. lbs. (43 Nm).
  2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
    1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
    2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).

  3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
  4. If removed, install the splash shield.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Hope helps (remember rated and comment this).

Jun 05, 2010 | 1989 Pontiac Bonneville

1 Answer

Install starter


  • Open the hood and locate the starter attached to the transmission bell housing. To inspect and remove the starter, it may be necessary to work under the vehicle. Park the vehicle on a solid level surface and set the parking brake. If the vehicle needs to be lifted, support it with jack stands.
  • Disconnect the negative battery cable, wrap the cable end with a shop towel and place it away from the battery post.
  • Mark the starter electrical wires for installation reference. Remove the starter wires.
  • Remove the starter mounting bolts. Remove the starter.
  • Compare the new starter with the old one to verify that you have the correct part.
  • Using a flashlight, inspect the flywheel teeth (through the opening in the bell housing) while an assistant turns the engine over by hand. You should replace the flywheel if any teeth are missing, cracked, or chipped.
  • Install the new starter. Torque the mounting bolts to the manufacturer's specifications.
  • Attach the electrical wires to the new starter.
  • Reconnect the negative battery cable.
  • Start the vehicle to verify the repair.

Feb 16, 2010 | 1992 Ford Explorer

1 Answer

How do I replace the starter on my 2004 Grand Am?


Alero, Grand Am 1999-2005 Repair Guide
Starter - Removal & Installation

2.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Starter electrical connector Starter motor

    781094e.jpg

    Fig. Starter mounting-2.2L engine
To install:
  1. Install or connect the following:
    Starter motor. Torque the bolts to 30 ft. lbs. (40 Nm). Starter electrical connectors Negative battery cable

3.1L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Starter electrical connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor. Torque the bolts to 32 ft. lbs. (43 Nm). Starter electrical connectors Negative battery cable
3.4L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Flywheel inspection cover Starter electrical connectors Starter motor
To install:
Install or connect the following:
Starter motor. Torque the bolts to 32 ft. lbs. (43 Nm). Starter electrical connectors Flywheel inspection cover. Torque the bolts to 89 inch lbs. (10 Nm). Negative battery cable


I hope helps with this. Good luck (remember rated this help).

Dec 29, 2009 | 2004 Pontiac Grand Am

1 Answer

Where do I find the starter for my 1997 buick lasabre - I need to replace this part.


  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
9795685.gif
Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion

ea58721.gif
Exploded view of the starter motor electrical connections

  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
d3e4880.gif
The starter is attached to the engine with 2 mounting bolts (see arrows)

aa0a8cb.gif
Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation

d22a19d.gif
Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle

Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.

e5e4cd3.gif
Exploded view of the starter motor mounting - 1987-97 vehicles

To install:
Note the location of any shims so they may be replaced in the same positions upon installation.
  1. Place the starter in position, then install the starter-to-engine bolts and tighten to 1 ft. lbs. (43 Nm).
  2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
    1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
    2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).
  3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
  4. If removed, install the splash shield.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Oct 31, 2009 | Buick LeSabre Cars & Trucks

1 Answer

BMW 328i Starter how to replaice


1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Sep 22, 2009 | 1999 BMW 328 Series

Not finding what you are looking for?
2000 Mitsubishi Diamante Logo

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...