Question about Cars & Trucks

1 Answer

No power to DLC

Complete engine replaced,complete tranny replaced.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,103 Answers

While engine running or no power from battery....what???

Posted on Jan 01, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Dlc no power at pmc distrbution fuse under hood

Check for power at the PCM power relay in the battery junction box under the hood in engine compartment !

Feb 05, 2015 | 2005 Ford Escape

1 Answer

Where is theTransmission Speed Sensor location on 1995 escort lx wagon?

Some of the trannys do not have the fill plug feature. On these trannys, you have to fill through the Vehicle Speed Sensor location (VSS). This is not fun. The VSS is located on the firewall side of the tranny, about in the middle of the tranny, down low. You can barely see it and reach it from the top of the engine compartment on the driver\'s side. You have to disconnect the VSS wire connector. Then, remove the VSS retaining bolt - this is a 10mm hex-head bolt in the tranny near the base of the VSS. The VSS must finally be pried carefully out of the case. Tranny fluid is filled through the VSS hole until full. Re-install the VSS and hook up the connector when complete. Have a box of Band-Aids ready.

If you have to change the fluid because you pulled the tranny, do yourself the favor of removing the speed sensor when the tranny is OUT of the vehicle. Then you can change the O-ring as well. Much easier not to damage the VSS which is a $60+ part to replace.

Aug 12, 2014 | Cars & Trucks

1 Answer

Drops in and out of gears and slows accelerates

is it the engine, power dropping
or tranny slipping
this is first. the tachometer tells you which easy.
slips tranny
loss of power , engine.
post which it is ,and if its the engine, do post which one of the many.

Feb 15, 2014 | 1992 Honda Accord

1 Answer

Accelerating uphill

loses power
well if the RPM advances fast on engine and the car speed dont
that is tranny slip.
on the other hand if the engine RPM stays low, and speed is low that
is engine power loose.
2 completly different things, why not ask him which it is.
is my engine weak or is the the tranny slipping.
surely you know what slip means. right>?
like bumping in to neutral , under power. or partially
ENGINE RPM state that, going up said hill WOT
and can tell you.

Jan 31, 2014 | 1997 Honda Odyssey

1 Answer

No data at DLC and theft light is flashing

Does the check engine light come on when you turn the key on ?

Jul 27, 2012 | Lincoln Continental Cars & Trucks

1 Answer

Check engine light and no power to DLC

Check the fuse that powers the DLC. It might be shared with the cig lighter or aux power sockets adn may have been blown.

Nov 20, 2009 | 2001 Chevrolet Blazer

3 Answers

Oil is in my engine coolant reservoir as well as my radiator

Most likely the intake manifold has a broken gasket or iteslf is broken.

take it to a shop and have them diagnose it by checking for HC's in your coolant. If there are non present, then it could be inside of the timing cover or the intake. If there are HC's present, you will need a new Head, Engine or just Head Gaskets, but if it's over 150,000 miles, you may want to just buy an engine if that's the case. You can't repair a high mileage engine with new top end components because it will "**** out" or ruin the bottom end shortly after installation.

Good luck! Hope that helps.

P.S. - I have mroe GM's come in with that same symptom than any other vehicle. After your repairs are complete, get rid of the DEXCOOL and go with a good, green antifreeze. It works much better than DEXCOOL.

Kevin, ASE Certified

Sep 12, 2009 | 1999 GMC Suburban

1 Answer

Engine is knocking has trouble shifting

If the noise is coming from the engine, it could be many things. broken, rod, valve, bent pushrod, generally means a complete teardown. If it's coming from the tranny, could be broken/bent flywheel, broken teeth on a gear, still another complete teardown.

Aug 29, 2009 | 1994 Dodge Dakota Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides