Question about 2002 Dodge Intrepid

1 Answer

2002 Dodge Intrepid transmission shifter cable

Is the 3.2 shifter cable the same as the 2.7 ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 3,103 Answers

Dealer or parts store can tell you..

Posted on Jan 01, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Serpentine/drive belt routing diagram of a 2002 dodge Intrepid needed.

Try this web sight. http://www.dodgeintrepidchat.net/02lhe/

Posted on Jun 04, 2009

leetamara
  • 702 Answers

SOURCE: My 2002 Dodge intrepid has it engine light on

The MAP sensor and Knock Sensor are both very easily replaced. A better scanner will tell you which sensor is going bad on your transmission. An Autozone code reader will not tell you which sensor on the trans. is acting up. Most sensors on your trans. are very easity replaced as well. They just screw in and plug it. It's worth paying to get a "real" scan done. The trans. sensors are inexpensive and you can replace any other your listed sensors yourself.

Posted on Jul 11, 2008

SOURCE: instructions & repair for dodge intrepid 2000 shifter cable

It's the shifter cable for sure. $15 + shipping from Moparpartsamerica.com

Posted on Aug 04, 2008

  • 321 Answers

SOURCE: 2002 dodge intrepid

I can look it up at work on Monday,and get back to you.

Posted on Aug 24, 2008

old marine
  • 2005 Answers

SOURCE: dodge intrepid 2002

The knock sensor is threaded into the block of the engine, just below where the cylinder head sits. You will need to remove the intake plenum (upper and lower) to access this part.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to change a shifter cable on a center console 2000 dodge Intrepid


Hello,

Google this: how to change shifter cable on a 2000 dodge intrepid - under videos.

I hope this helps

Oct 29, 2017 | 2000 Dodge Intrepid

1 Answer

2002 dodge intrepid problems


If your headlights turn on and seem as bright as they should be or you've already checked battery and connections... Then turn ignition switch on depress brake pedal move shifter to neutral then key to start... or hold key in start position and foot on brake and wiggle shifter in and out of Park

Mar 25, 2014 | 2002 Dodge Intrepid

1 Answer

Why will my 2002 dodge intrepid start perfectly in cold weather, but not in hot weather, or as the temperature rises during the day? Priscilla TravisBefore it would only start in cold weather, and not


Could be the neutral safely switch is still not adjusted properly. With your foot on the brake and the transmission in neutral, move the shifter a little bit in either direction while holding the key in the start position. If the starter engages, the switch needs to be adjusted.

Aug 26, 2017 | 2002 Dodge Intrepid

1 Answer

2002 es intrepid wont go into park and is hard to get into reverse, is this a cable problem, otherwise car runs great


Did you have any work done to your transmission recently? If you did and it was done buy a transmission shop shame on them. This is an internal problem that occurs when the trans valve body is removed on your trans which I believe to be a A606/42LE. There is a shift plate at the bottom of the shift lever, this plate can get bent if the steering wheel shifter is not placed into the lowest gear before removing the valve body. This is an easy fix , but everything has to come out again. You would have to see it to understand. So if this was done ,this is your answer, if not then it maybe your shift cable. It may need replacing our lubrication. GOOD LUCK.

Aug 04, 2011 | 2002 Dodge Intrepid

1 Answer

2004 Intrepid transmission/coulumn shift problems


The shifter cable is adjustable in the column. Remove the column covers and see if you can adjust the cable. You problem is with the cable.

May 02, 2010 | 2004 Dodge Intrepid

1 Answer

2002 Dodge Intrepid ES shift selector is stiff, difficult to move into position. Is this a linkage rebuild issue?


You have a shift cable. This cable may be getting a
little worn. One way to check it is, disconnect the
cable at the transmission and see if it is still stiff.
Look under the hood, just to the right of the brake
booster. You will see 2 cables that come through
the firewall, one is the throttle cable, it will go to the
right towards the center of the engine. The other is
the shift cable, it will go down to the transmission
linkage. Disconnect the cable there and see if it
shifts any easier. If not, replace the cable.
Hope this helps. Good luck.

Feb 07, 2010 | 2002 Dodge Intrepid

2 Answers

Hard to shift into park


I have a 97 intrepid and also had problems shifting in to park, the problem turned out to be the body to frame isalator bushings were bad .these rubber bushings are under the car mounted to a U shaped frame member that help hold the engine and transmission in place once the bushings go bad the transmission shifter cable becomes miss-alligned and cannot move properly

Jul 12, 2009 | 1993 Dodge Intrepid

1 Answer

Hard to move Gear Shifter in a 2000 Dodge Intrepid ES


I had the same problem after my car went into a transmission shop for some service. This might be the solution, it was with my car. Check the transmission shift cable. When mine finally failed, it was filled with rust.
You may be able to simply lubricate it somehow with something like WD40, but I'm not sure if it would work. If all else fails, you can have the shift cable replaced, which is what I had to do with my car after driving it for 2 years with that problem. By then I had worn out and warped the shifter and had to replace that too, as well as drive it around for a week without being able to get the transmission into park.
Good luck! If you have to take it to a shop, just tell them that your shift cable is going bad and you want them to make sure.

Apr 08, 2009 | 2000 Dodge Intrepid

Not finding what you are looking for?
2002 Dodge Intrepid Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...