Question about 2005 Peugeot 405

1 Answer

How do l reprogramme key fob on 01y plate peugeot expert van the remote will not lock only unlock.

The remote will not lock, only unlock, so l have to lock manually with key. Hence the alarm is not set.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Peugeot Master
  • 3,103 Answers

Dealer can tell you..

Posted on Jan 02, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 205 Answers

SOURCE: fob wont work the locks

I have done this procedure for my peugeot 307, but you can give it a try for your Pug expert and let me know if it works.
Disconnect the battery for 5 minutes then after connecting the battery perform the following steps
1. Turn the Ignition switch to the ON position using your key.
2. Press the LOCK button for 10 seconds. It will set your ECU in programming mode.
3. Remove the key and wait for 10 seconds.
4. Press the buttons on the key repetedly for operation (lock und unlock doors) to synchronise the key signals.
5. Again turn the ignition on and start the engine.
6. Turn the ignition OFF

If fails in step 4, then disconnect the battery and reconnect it and wait about 10 minutes to check the remote. Some new ecu units synchronises itselfs if you disconnect the battery while in programiing mode.

Posted on Jun 13, 2009

  • 1 Answer

SOURCE: key fob wont work on my Peugeot Expert

Try this, press and hold the large button on your key fob,after 20 seconds press the small button while still pressing the large one, the led light will go out and will reset your remote. It worked for me. ray1297

Posted on Oct 23, 2009

  • 1 Answer

SOURCE: i need to reset my peugeot 406 key fob

Had same trouble with my 406, fixing no problem, with new battery in fob, insert into ignition, turn key, BUT DO NOT START ENGINE, hold button for about 10 seconds release button and remove key from ignition, then try and see if doors lock on remote, if not try again, had to do this a couple of times, and it worked, sorry to say that now my key fob button has completely fell apart, through ware and tare

Posted on Feb 10, 2010

  • 98 Answers

SOURCE: key fob on my 54 plate peugeot expert van will not

most cars need a reset when being worked on even as simple as changeing the battery find fuse box look for fuse Labled (hazard or HZD) remove for 15.sec. then put back in it should reset the ECU

Posted on Apr 04, 2010

  • 1 Answer

SOURCE: Peugeot Expert van Alarm

You don't have an alarm. The red light should flash with keys out doors closed. It is a bit of bluff.

Posted on Apr 09, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Peugeot saying plip battery spent, where can I get new battery from


The warning is regarding the battery in you key fob remote, used for central remote locking and alarming your car and registering the key to the car. It takes a small flat battery like a watch battery: CR1620-Lithium-Battery. You may have to reprogramme it after changing the battery though. Purchased from Peugeot or any good electrical store.

Dec 31, 2015 | Peugeot Cars & Trucks

1 Answer

My 2004 Town and country van had to be jump started and now key fob won't lock or unlock doors.Took key fob to locksmith he said key fob was working, van was not reading signal and he didn't know what


The fob may need to be reprommed to the car. Do the following:

Grab your working remote. Push the LOCK button five times, allowing exactly two seconds to pass between each press of the LOCK button. Insert the ignition key and turn it to RUN. Push and hold UNLOCK on the working remote for 6 seconds. Push and hold PANIC for one second while continuing to hold UNLOCK. Release both buttons at the same time.
Push any button on the remote to program it. Then push any button on the remote that was already programmed. It has to be reprogrammed. The remote is now programmed to the vehicle. Turn the key to OFF.

Oct 28, 2014 | Cars & Trucks

1 Answer

Since disconnecting the battery on my peugeot expert van my alarm doesn't bleep when I lock the door with the key fob.


On my Civic there was a button on the underside of the key fob that I had to hold to enable/disable the beep when I locked my car. Hope this helps.

Sep 13, 2014 | Cars & Trucks

1 Answer

Expert van


possibly a battery problem Get an AVR check done that will check your power supply for the vehicle

Sep 15, 2013 | 1987 Peugeot Liberte

1 Answer

C Class Mercedes Remote Key Fobs stopped working


You may need to reprogramm the remotes tothecar again. That needs to be done by the MB dealer with a special tool and can't be done at home.

Jun 25, 2012 | Cars & Trucks

2 Answers

How do i program my ford key fob 2 my transit van


1 - Unlock the doors. Put the key in the ignition, and turn from "Off" to "ACC" 8 (eight) times in under 10 seconds. The doors will lock. Leave key in the "ON" position

2 - Program the fobs by pressing any key on the fob. The doors locks will lock/unlock

3 -- Turn the key to Off. Locks will lock/unlock, and you are out of programming mode.

I bought new remote Key Fob on Ebay and it did work properly on my Ford Transit LWB 2003. Good Luck!

Mar 22, 2012 | Cars & Trucks

1 Answer

Key fob on my 54 plate peugeot expert van will not work after replacing the battery,no visible led on fob


most cars need a reset when being worked on even as simple as changeing the battery find fuse box look for fuse Labled (hazard or HZD) remove for 15.sec. then put back in it should reset the ECU

Apr 04, 2010 | 2005 Peugeot 405

2 Answers

Key fob wont work on my Peugeot Expert


Does the battery need changing on the key fob?
you can check by using you'r mobile phone cam & pointing the key fob (ultra violet bulb) at the lens when pressing the button, you should see the light flashing on the key fob looking through the camera, you can use any camera, most of them will see the light as it's out of our sight range but cameras pick it up.
If not then unscrew the key fob & split it carefully (use an old credit card not a knife or screwdriver) & change the battery.
If the fob work's then the problem is with the receiver, usually up by the rear view mirror.
Hope this help's !

Sep 21, 2009 | 2005 Peugeot 405

1 Answer

My renault laguna 1999 rt remote key fob wont work?


IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Jul 09, 2009 | 2004 Renault 181

1 Answer

Fob wont work the locks


I have done this procedure for my peugeot 307, but you can give it a try for your Pug expert and let me know if it works.
Disconnect the battery for 5 minutes then after connecting the battery perform the following steps
1. Turn the Ignition switch to the ON position using your key.
2. Press the LOCK button for 10 seconds. It will set your ECU in programming mode.
3. Remove the key and wait for 10 seconds.
4. Press the buttons on the key repetedly for operation (lock und unlock doors) to synchronise the key signals.
5. Again turn the ignition on and start the engine.
6. Turn the ignition OFF

If fails in step 4, then disconnect the battery and reconnect it and wait about 10 minutes to check the remote. Some new ecu units synchronises itselfs if you disconnect the battery while in programiing mode.

May 23, 2009 | 2005 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...