Question about Cars & Trucks

Open Question

KNOCK SENSOR LOCATION ON TOWN & COUNTRY 3.3 - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
short shadey
  • 421 Answers

SOURCE: location of the speed sensor on 1996 town & country

they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Posted on Sep 04, 2008

Ad
  • 740 Answers

SOURCE: I need location of oxygen sensor on a 2001 town & country

ALL of your oxygen sensors are located i your exhaust system Your exhaust system starts at the exhaust manifold on the side of the engine and ends at the tail pipe by you back bumper. Your vehicle oxygen sensors are 4 of them there are two on each side of your exhaust the are actually screw into the exhaust they are like the nose of you engine to read how rich/lean the car is running. The are pretty simple to replace, they look kinda like spark plugs with wires attached to them the wires are usually colored white black and grey with plug connections on the end. To replace get a oxygen sensor socket and a ratchet and unscrew this socket can be bought at almost any auto parts place like auto-zone etc. Good luck and thanks for using FIX YA

Posted on Mar 22, 2009

  • 323 Answers

SOURCE: locassion of output speed sensor on 2003 Town and Country

The input and output speed sensors look identical on the connector side. The one over the solenoid pack is the input, the one closer to the left frame rail or left front wheel is the output sensor. I hope this helps.

Posted on Apr 26, 2009

motor1258
  • 6674 Answers

SOURCE: diagram or location of knock sensor

Look under exhaust manifold on drivers side, closer to rear of engine . mounted on engine block.

Posted on Jun 01, 2009

autotherapis
  • 501 Answers

SOURCE: Where is the neutral safety switch located on 1998 Town & Country

It is built into the valve body of the transmission. It can be replaced, but it should be done by a pro. What are the symtoms that make you ask>

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant find door sensor 2002 chrysler town & country


I know on my ford ranger the switch is located inside the door such that when the door latch rotates around the lock pin, it actuates the switch. If you don't see the switch in the door jamb, pull the inside door panel off and take a look around, focusing on the area around the latch.

Mar 11, 2014 | 2002 Chrysler Town & Country

1 Answer

2005 Chrysler Town & Country MAP Sensor location


The MAP sensor is mounted to the intake manifold, near the throttle body inlet to the manifold. The sensor connects electrically to the PCM.

zjlimited_2083.jpg

Hope this helps. Your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 25, 2011 | 2005 Chrysler Town & Country

1 Answer

How do you locate the upstream o2 sensors on a 1996 chrysler town & country with a 3.8 liter engine?


upstream means above or before the catalytic converter, check this link for Chrysler and Dodge 3.8 locations, the have a diagram for you too look at http://autorepair.about.com/library/images/bl341lib.htm

Sep 01, 2011 | 1996 Chrysler Town & Country

1 Answer

Picture of bank1 sensor1 o2 sensor location on 2001 chrysler town & country


I do not have a diagram but, bank 1 is the bank where #1 cylinder is at. other side would be bank #2. so bank #1 o2 sensor is just before convertor.

Aug 29, 2010 | 2001 Chrysler Town & Country

1 Answer

2005 Chrysler Town & Country Service tire system soon light coming on after new tires have been put on, pressure checked & tires balanced?


Maybe when you change the tires they remove or broke one or the four sensors located inside the rim or wheel, at the inside of the valve, this sensors transmit the low pressure to the computer, and if one, or all, are removed or damaged, computer will register it at as a low pressure tire

Aug 01, 2010 | 2005 Chrysler Town & Country

2 Answers

Oxygen sensor1 bank1, need to be location


the first one on the right hand side before the catalytic converter

Mar 13, 2010 | 2001 Chrysler Town & Country

2 Answers

Knocking in the engine at startup and idle


If the knocking is a very low hammering sound its the rear main bearing to the crack shaft gone bad

Jan 16, 2010 | 2001 Chrysler Town & Country

1 Answer

Cam sensor on 2001 Chrysler Town and country


depending on what size motor you have, the 2.4 has the sensor mounted on the rear of the cylinder head. the 3.3 & 3.8 engines have them mounted on top of the timing case cover, Good Luck!

Sep 19, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...