Question about 2001 Land Rover Discovery Series II

1 Answer

NO SPARK AT SPARK PLUG

WHERE IS CRANK SENSOR SITUATED

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Land Rover Master
  • 3,103 Answers

Parts store can tell you. even give detailed intsructions on replacement.

Posted on Jan 01, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Detailed explanation on why my car will not start why does my ignition coil packs not spark the spark plugs what steps do I have to back due to backtrack and find the solution


run the fault codes for a start to find possible reasons for the situation
check cam/crank positions sensors ( either or or broken timing belt
check that the immobilizer is operational

Oct 21, 2015 | Cars & Trucks

1 Answer

Jeep cranks but does not start


Hi, First replace your plugs. Second check ignition coil(s) one maybe bad. replace with new. If all else is good, have your mechanic check the computer codes. (code scanner) Many of todays cars and trucks have computers to run and control the engine. (management system). Good luck

Feb 04, 2015 | 2004 Jeep Liberty

1 Answer

Ihave changed the crank sensor and the coles on the plugs but still the it wont give a spark.


DID YOU CHECK THE COIL PACK.........THIS SENDS A SPARK TO YOUR SPARK PLUG

Apr 15, 2014 | 2005 Toyota RunX 160i

1 Answer

Crank shaft sensor, 99' taurus


If the crank sensor is bad you will not get any spark. The PCM does not know the engine is turning with no crank sensor signal so it it does nothing.

What else is it doing?

Feb 24, 2014 | Ford Taurus Cars & Trucks

1 Answer

My 1991 oldsmobile eighty eight royale keeps dying when i drive it, I have replaced ing control moduel, fuel pump, mass air flow , cam shaft sensor, timing chain, plugs wires ect. do i need to keep...


With that much already invested, why give up now? How about the crank position sensor-was that replaced as well? For spark control and spark timing, the computer needs inputs from both the cam position sensor and the crank position sensor before it can know when to cut power to the coils for spark to occur.
Before proceeding any further, you should check for diagnostic trouble codes. You would need an OBD 1 type code reader or scanner for your olds. Any stored codes may help you find the problem.
You can test the ignition system by checking for spark on a spark plug wire when the engine is cranking over. Pull the plug wire off a spark plug and put in a clean spark plug into the wire. Lay the plug so the threads are touching metal on the engine somewhere. Have someone crank the engine over and watch for a spark from the spark plug. If you have a blue, snapping spark when cranking, ignition is good.
One last note: since it dies when driving, there is a possibility that you have a malfunction in the pcm-the computer.

Jan 22, 2013 | Cars & Trucks

1 Answer

We replaced the Water pump and Timing belt on a 1999 Plymouth Neon 2.0 Single Overhead Cam Engine. Engine Cranks, Is getting Fuel...but no spark. We changed the Coil Pack. It still cranks, but no...


If its not getting spark the choices are limited. You already replaced the coil pack so whats left is ignition module, crank sensor, knock sensor, cam sensor, or the timing was not was not set properly when putting it back together. Any one of those would create a no spark situation.

Mar 17, 2011 | 1999 Plymouth Neon

2 Answers

Won't start turns over no spark


You need to check your distributor/coil pack, dist cap, rotor, plug wires, It may be your cam sensor. Try to get any codes you can receive. Have you checked the timing belt?

Mar 08, 2011 | 1994 Jeep Grand Cherokee

1 Answer

2001 nissan not getting spark 2 spark plugs just turns over is it crank sensor


If you have the 1.8L check for voltage at oil pack if voltage there more then likely bad coil's, crankshaft sensor ok if you have spark at other cylinder's.If 2.0L check spark plug wire's, crank sensor in distruibutor.

Jan 16, 2010 | 2000 Nissan Sentra

1 Answer

Crank, no start 98 wrangler 2.5l


crank sensor likely-may be distributor sensor but my 98 sport was crank sensor situated in bell housing timed by flywheel

Sep 15, 2009 | 1997 Jeep Wrangler

Not finding what you are looking for?
2001 Land Rover Discovery Series II Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...