Question about Ford Transit

Open Question

2.2l Ford Duratorq diesel location of oil sender

2008 model Ford Transit 2.2litre diesel engine. Where is the oil pressure sender unit. Suspect there is an oil leak.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1201 Answers

SOURCE: Location of Oil Pressure Sensor and Oil Pressure Relieve Valve

the oil pressure switch is on pssenger side, lower engine area,beside oil filter, mounted in engine block. The pressure relief valve is in the oil pump, in which case, you have to drop the oil pan,and take off the oil pump.

Posted on Jan 31, 2009

  • 29 Answers

SOURCE: oil pressure sender

It is located on the side of the oil pan, enclosed is a little more info on testing and installation.

TESTING
See Figure 1

  1. Unplug sensor connector and insert a jumper wire between terminals 1 and 2.
  2. Start the vehicle.
  3. If the light is on, check the harness and dashboard light.
  4. If the light is off, replace the sensor and recheck the light operation.
0900c1528008c49c.jpgFig. 1: Connect a jumper wire between terminals 1 and 2REMOVAL & INSTALLATION
See Figures 2, 3 and 4
  1. Raise and safely support the vehicle.
  2. Unplug the connector from the sensor.
  3. Unfasten the sensor mounting bolts and remove the sensor from the oil pan.
To install:
  1. Install the sensor into the oil pan.
  2. Tighten the sensor mounting bolts.
  3. Plug in the sensor connector.
  4. Lower the vehicle.
0900c1528008c49d.jpgFig. 2: The oil pressure sensor is mounted to the side of the oil pan-850 model shown 0900c1528008c49e.jpgFig. 3: Unplug the connector from the oil pressure sensor 0900c1528008c49f.jpgFig. 4: Unfasten the retaining bolts and remove the sensor

Posted on Oct 01, 2008

  • 170 Answers

SOURCE: 02 jeep grand cherokee 4.7 eng

Hook up a manifold gauge (mechanical temporary use gauge, used by mechanics) and test the oil pressure. You probably need to replace the gauge. The computer sends info through a printed circuit board behind gauge cluster and sometimes you have to replace the whole gauge cluster.

Posted on Feb 06, 2009

  • 1 Answer

SOURCE: Location of oil pressure sending unit on 2003 GMC 4.3L

2 the right of dist. cap

Posted on Apr 07, 2009

ftw1952
  • 10319 Answers

SOURCE: I have a 2002 Ford Ranger Edge, with a 3.0L

near the oil filter area

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 sedona oil light on


Remove the oil light sender unit, fit a oil pressure gauge start engine if oil pressure present replace sender unit, if no pressure oil pump is at fault or pressure valve stuck open

Apr 03, 2017 | Kia Sedona Cars & Trucks

1 Answer

Where the heck is the oil pressure sensor on a diesel rodeo


disregard auto advice as there is no connection
oil pressure sensor switches are located in the oil galley along the block or next to the oil filter housing
normally only one wire
I suspect that the wire to the switch is loose and not making proper contact
The fix here is to eliminate any mechanical problems ( pump and filter blockage ) by having an accredited service center remove the sender unit and fit a mechanical oil gauge to see what is happening with the pressure
If it reads within the specified limits, replace the sender unit or check the wire for loose , broken or shorting out

Aug 10, 2016 | Holden Cars & Trucks

1 Answer

Where is the location of the oil pressure sender on a 2014 awd Chevy Equinox?


The AWD Equinox has two model selections (LS & LT) and two 2.4L engine options (K2.4L FI DOHC & the K2.4L Flex Fuel DOHC.)

Information on the Equinox engines oil pressure senders location is difficult to find on line so all I can offer in the way of help is to say that It will be on the engine block connected to the ECM (engine Control Module) with a single TN/BK (Tan/Black) wire lead.

The Oil Pressure Sender is a distinct looking unit that is sold by Autozone and they provide pictures of the various makes which should help you identify the units location on your engine block.


Gauge Sender

Aug 07, 2016 | Chevrolet Equinox Cars & Trucks

1 Answer

I have KIA sorento 2.5 diesel 2009 model and it was overhaul engine and now the the oil lump keeps on flicking when reducing speed or idling after getting warm, What could be the problem


Remove the oil sender unit, fit a oil pressure gauge , start the engine and read the oil pressure at idle engine hot, must read above 10 psi and needle not flicking, must increase with engine speed , if pressure is ok replace censer, if not check oil pump screen and relief vale spring, can also be caused by crankshaft bearings clearance .

Jul 02, 2015 | 2007 Kia Sorento 4x4

1 Answer

Where is oil filter located on a 2002 ford transit diesel manual engine


Of it has a 6.0L engine it is on top of the engine righ where a carburator supposs to go, this is for a ford f350 diesel

Oct 12, 2012 | Ford Transit Cars & Trucks

2 Answers

Where is coolant temp sensor located


Not sure of your engine size so please pick the appropriate diagram:


22070ae.gif

Coolant temperature and oil pressure senders-4.3L engines



b65ae41.gif

Coolant temperature and oil pressure senders-5.0L and 5.7L engines



c1bcdb8.gif

Coolant temperature and oil pressure senders-7.4L engines



dd2f3ba.gif

Coolant temperature and oil pressure senders-6.2L and 6.5L diesel engines

Sep 15, 2010 | 1994 GMC Sierra

1 Answer

Oil pressure gauge not reading on my 1994 jeep wrangler. oil is full just the guage has no pressure and not alot of power


The oil pressure specification for your engine is 13 PSI at idle hot, 37 to 75 PSI at engine RPM higher than 1600. I suspect your oil pressure gauge sender unit or gauge is inaccurate. I would have a known accurate mechanical oil pressure gauge temporarily screwed into the present oil sender unit to verify actual pressure.

If you have the correct pressure I would replace the sending unit first.

Sep 23, 2009 | 1994 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...