Question about Cars & Trucks

1 Answer

Got superglue on granite counter top how do I remove it without damage to counter top

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Cars & Trucks Master
  • 803 Answers

Razor blade, tilted almost flat, work the blade under the glue.

Posted on Jan 01, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Took the finish off a 9x12 area of my countertop. It is dull rough feeling. How to I restore that portion of the countertop? Thank you.

if it is a formica or other type of top finish then I suspect that you have damaged the plastic surface of the counter top
I would seek the advice of a shop that makes and supplies counter tops but I suspect that you will need a new top

Jul 04, 2015 | Cars & Trucks

1 Answer

The plastic areas of my cars door panel and shift cover area have been damaged by super glue spills can it be repaired

No damage done my friend. Sure, super glue sticks, but on plastic it just sticks to the surface, doesn't soak in. Just get a razor blade under the superglue and it will peel right off by pulling it.

Sep 24, 2014 | Cars & Trucks

1 Answer

Damaged car interior door panel and shift casing area how can I repair it myself

No damage done, no repairs required. Just use a razor blade to get under the dry superglue and it will peel right off.

Sep 24, 2014 | Cars & Trucks

1 Answer

Superglue remove

nail polish remover painted on with a nail brush will most likely do the job. .super glue doesn't like acetone so if that doesn't work paint on acetone very carefully.

Jan 05, 2014 | Cars & Trucks

1 Answer

How to replace a fuel strainer on a 2000 Nissan maxima

Remove rear seat now u have access to fuel pump. Remove cover disconnect wire harness. Then there is a big plastic screw top which goes around whole pump and secures it to fuel tank. Turn counter clockwise with some force without breaking it. The remove pump slowly so you dont break fuel level float. Now you should have access to the strainer.

Nov 04, 2013 | Cars & Trucks

1 Answer

I need to replace the blinker lamp rear drivers side. How do I remove the cover to get to the lamp without damaging the lenses?

Bulb replacement is done from the rear of the light. Open you trunk and remove the cardboard / carpet cover. When you get to the bulb socket holder, simply twist it counter clock wise a little, and remove.

Aug 10, 2010 | 1997 Oldsmobile Cutlass Supreme

1 Answer

How to remove the fuel pump from a ford explorer 1996 can not get fuel pump off of gas tank

Removing the fuel pump requires lowering the fuel tank from the vehicle, the fuel lines require special tools to remove the lines from the pump without damaging the lines( tool availiable at parts store) then remove the lock ring by turning counter clockwise , then the pump , is held to the bottom of the tank by a clip on each side of the pump once depressed the pump will come out.

May 29, 2010 | 1996 Ford Explorer

1 Answer

How to change Shocks on 2001 Golf

My procedure removing front shocks:

  • Before I raise the car and place on jack stands, I loosen the top nut on the strut bearing. If you don't have an air gun to remove the nut there are tools available from online tool shops. A 1/2" drive breaker bar is attached on top of the tool while an allen wrench seen in the middle counter acts the by holding the strut in place.


Tool without the allen to use as a counter act, used with a regular L allen wrench.

  • Remove bolts that secure the swaybar to the control arm.
  • Use this tool to remove the tie rod ball joint with this tool.f1c8d52.jpg
  • With a automatic center punch tool, mark three reference points on the lower control arm ball joint flange (not on control arm. This will help line up the ball joint to the control arm without messing alignment putting back together.
  • Remove the 3 bolts that secure the ball joint to the control arm and wiggle out the ball joint and the wheel bearing housing away from the control arm.
  • Remove the large bolts that secure the strut to the wheel bearing assembly, this will somewhat loosen the hold on the strut.
  • With a long pry bar or a long pipe wedged on the control arm, position it when the time comes you need to counter act downwards.
  • On the wheel bearing assembly where the strut is buried, there will be a slot which you need a 1/4" drive extension attached to a 1/4" ratchet wedged into the slot.
  • Crank the ratchet slowly until it spreads the slot securely and wide enough to release the strut assembly.
  • With the strut separated from bearing assy. secure the strut from dropping and loosen the top nut above the strut bearing, remove strut from vehicle.
I don't know how far you want assistance but if need further info just let me know.

May 27, 2010 | 2001 Volkswagen Golf

1 Answer

Subaru Liberty 2004

how do i remove the clock unit from a 2004 subaru liberty from the dashboard

Mar 03, 2009 | 2005 Subaru Legacy

1 Answer

Removal of Headlamp bulb?

The Xterra doesn't have stock xenon headlights, so are your lights aftermarket? If not, there is a retaining ring on the back of the headlight housing (under the hood) and you just turn the ring counter clockwise to detach and the the bulb comes right out. Installation is the reverse of removal.

Nov 15, 2008 | 2002 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides