Question about 2008 Suzuki XL7

1 Answer

Evap purge solenoid

Where is located?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

First off, the real FSM covers all this, incliding the tedious tests
so is the alldata.com page on EVAP.
on most cars, you open hood
you see the EVAP charcoal canister there. its BIG.
see it. and all those hoses, they go to tank and to the solenoids
very close.
newer cars, 97+ have more that one valve to tell each one.
see same books above. or if in the USA< (not stated)
you open hood,look up,see EPA sticker,. and the VACUUM map
bingo.

Posted on Jan 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the purge valve solonoid for a 2000 chevy cavalier?


How do I test a purge solenoid? / Diagnosing an EVAP ...

www.ericthecarguy.com/.../13335-how-do-i-test-a-purge-solenoid-diagn...
My brothers 2000 Chevy Cavalier has a P0440 code. ... the PCM will test the circuit condition of the purge valve solenoid and vent valve solenoid so with the key ...

P0446 2000 chevy S10 4WD Replacing EVAP Vent Valve ...

? 7:54
https://www.youtube.com/watch?v=EVWDc9sM1Co
May 7, 2014 - Uploaded by omar ERA
code .P0446. ... Chevy Truck Hard To Fill Gas Tank - GM EVAP Codes P0442, P0446, P0455 or P0449 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... Hi, is thispurge can solenoid in the same location for ...

Dec 19, 2015 | 2000 Chevrolet Chevrolet Cavalier Base

1 Answer

Where is purge valve solenoid located?


Mar 16, 2014 - 2 posts - ‎1 author
I have a 2003 Vue 3.0L 2wd.After fueling I have trouble starting, it cranks but I have to pump it a couple of time then it starts, Sometimes after it ... 2008 Saturn Vue Purge valve canister solenoid location ...
9 posts
Aug 24, 2013
access to vent valve solenoid - SaturnFans.com Forums
2 posts
Jan 20, 2013
Service engine soon light: P0440 - SaturnFans.com Forums
6 posts
Apr 15, 2010
Code P0446 (evap solenoid) and now I can't fill the gas ...
16 posts
Nov 17, 2007
More results from www.saturnfans.com

EVAP Solenoid Location - YouTube

? 2:17
https://www.youtube.com/watch?v=jIKaPF2Yw3I
Mar 20, 2007 - Uploaded by richpin06a
Saturn EVAP Solenoid Location. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by CarsNToys ...

EVAP Purge Solenoid Removal - YouTube




Dec 11, 2015 | 2003 Saturn VUE

1 Answer

I have a 1999 oldsmobile aurora, northstar motor. I was told I need to replace my purge valve solenoid. Can someone please tell me where it is located?


It's under the plastic cover on top of the engine . Remove the intake manifold top cover.
Remove the solenoid quick-connect hose (3) at the EVAP canister purge solenoid (4). Remove the solenoid quick-connect hose (7) from the EVAP canister purge solenoid (4) to the enhanced EVAP service port (8). Remove the electrical connector (6) at the EVAP canister purge solenoid. Remove the EVAP canister purge (2) solenoid valve bolt. Remove the EVAP canister purge solenoid tab from the bracket (5).

Aug 06, 2015 | 1999 Oldsmobile Aurora

1 Answer

P1655 came up on diagnostic test for my 1997 Pontiac grand prix. What is it and where is it located on engine? How much is it gonna cost?you


It could just be a electrical problem !
A DTC P1655 set indicates an improper voltage level has been detected on the EVAP canister purge solenoid circuit , Can you check electric circuits with a volt ohm meter ?
Diagnostic Aids
Check for the following conditions:
?€¢
Poor connection at PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.


?€¢
Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition ON and observe a voltmeter connected to the EVAP Canister Purge solenoid driver circuit at the PCM harness connector while moving connectors and wiring harnesses related to the EVAP Canister Purge solenoid. A change in voltage will indicate the location of the fault.


Test Description
The numbers below refer to the step numbers on the Diagnostic Table.

  1. Normally, ignition feed voltage present on the output driver circuit with the PCM disconnected and the ignition turned ON.

  2. Checks for a shorted component or a short to B+ on the output driver circuit. Either condition would result in a measured current of over 1.5 amps. Also checks for a component that is going open while being operated, resulting in a measured current of 0 amps.

  3. Checks for a faulty EVAP canister purge solenoid.

  4. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming
Step
Action
Value(s)
Yes
No

1

Was the Powertrain On-Board Diagnostic System Check performed?
--
Go to Step 2
Go to Powertrain On Board Diagnostic (OBD) System Check

2
  1. Ignition OFF, disconnect the PCM.
  2. Ignition ON.
  3. Using DMM (J 39200), measure voltage between the EVAP canister purge solenoid driver circuit at the PCM harness connector and ground.
Is voltage near the specified value?
B+
Go to Step 3
Go to Step 6

3
  1. DMM to 10 amp scale, install DMM to measure current between the EVAP canister purge solenoid driver circuit and ground.
  2. Monitor the current reading on the DMM for at least 2 minutes.
Does the current reading remain between the
specified values?
0.1 amp - 1.5 amps
Go to Step 11
Go to Step 4

4
  1. Disconnect the EVAP canister purge solenoid (leave the PCM disconnected).
  2. Using DMM, measure voltage between the EVAP canister purge solenoid driver circuit and ground.
Is voltage at the specified value?
0V
Go to Step 14
Go to Step 5

5

Locate and repair short to voltage in the EVAP canister purge solenoid driver circuit (refer to Engine Electrical).
Is action complete?
--
Go to Step 16
--

6

Check the ignition feed fuse for the EVAP canister purge solenoid.
Is the fuse blown?
--
Go to Step 7
Go to Step 8

7

  1. Locate and repair short to ground in ignition feed circuit for the EVAP canister purge solenoid. Refer to Fuse Block Details in Electrical Diagnosis.
  2. Replace fuse.
Is action complete?
--
Go to Step 16
--

8

  1. Disconnect the EVAP canister purge solenoid.
  2. Ignition ON, measure voltage between the ignition feed circuit for the EVAP canister purge solenoid and ground.
Is voltage near the specified value?
B+
Go to Step 9
Go to Step 13

9

  1. Check the EVAP canister purge solenoid driver circuit for an open or a short to ground.
  2. If a problem is found, repair the EVAP canister purge solenoid driver circuit.
Was a problem found?
--
Go to Step 16
Go to Step 10

10

  1. Check the EVAP canister purge solenoid driver circuit and the ignition feed circuit for a poor connection at the EVAP canister purge solenoid and at the PCM.
  2. If a problem is found, replace faulty terminal(s).
Was a problem found?
--
Go to Step 16
Go to Step 14

11

  1. Ignition OFF, reconnect the PCM and disconnect the EVAP canister purge solenoid.
  2. Ignition ON, connect a test light between the EVAP canister purge solenoid driver circuit and the ignition feed circuit at the EVAP canister purge solenoid harness connector.
  3. Using the scan tool outputs test function, cycle the EVAP canister purge solenoid ON and OFF.
Does the test light flash ON and OFF?
--
Go to Diagnostic Aids
Go to Step 12

12

  1. Check the EVAP canister purge solenoid driver circuit for a poor connection at the PCM.
  2. If a problem is found, replace faulty terminal.
Was a problem found?
--
Go to Step 16
Go to Step 15

13

Locate and repair open in ignition feed circuit to the EVAP canister purge solenoid. Refer to Engine Electrical.
Is action complete?
--
Go to Step 16
--

14

Replace the EVAP canister purge solenoid.
Is action complete?
--
Go to Step 16
--

15
Replace the PCM.
Important: Replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming .
Is action complete?
--
Go to Step 16
--

16

  1. Ignition ON, engine OFF, review and record scan tool Fail Records data.
  2. Clear DTCs.
  3. Operate vehicle within Fail Records conditions as noted.
  4. Using a scan tool, monitor SPECIFIC DTC info for DTC P1655.
Does scan tool indicate DTC P1655 failed this ignition?
--
Go to Step 2
Repair complete

Apr 08, 2015 | Pontiac Cars & Trucks

1 Answer

Purge solenoid location 2008 torent


Evaporative Emission Canister Purge Solenoid Valve Replacement
Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Disconnect the engine wiring harness electrical connector (4) from the evaporative emission (EVAP) purge solenoid.
Remove the oil fill cap. Lift upward and remove cover from ball studs.
The purge solenoid is under the plastic cover on top of the engine .
Disconnect the EVAP pipe quick connect fitting (1) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the EVAP pipe quick connect fitting (2) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service. Remove the EVAP purge solenoid bracket bolt (3). Remove the EVAP purge solenoid.

the purge

Sep 20, 2014 | 2008 Pontiac Torrent

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

1 Answer

Need to know where to find the canister purge valve


For the location of canister purge valve,check the following help links mentioned below:--
Click the link :---

Location for EVAP Purge Valve Solenoid?

http://schematicsdiagram.blogspot.in/2012/06/2002-nissandatsun-pathfinder-location.html


------------------

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

-------------

2004 Chrysler PT Cruiser: Location of EVAP Purge Solenoid Valve?

http://schematicsdiagram.blogspot.in/2012/06/2004chrysler-pt-cruiser-location-of.html

-----------
These will help.
Thanks.

Jan 08, 2013 | Cars & Trucks

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Were is the evap located on 2001 Chevy s-10 blazer with v6


The EVAP service port is located in the EVAP purge pipe between the EVAP purge solenoid and the EVAP canister. The service port is identified by a green colored cap.

47e8f38.jpg

Fig. Showing location of (1) Evaporative Emissions (EVAP) Canister Purge Solenoid and (2) Exhaust Gas Recirculation (EGR) Valve


4d7b3e9.jpg

Fig. EVAP Purge valve solenoid (3) mounting bolt (2) and insulator (1) on 2000-2005 4.8L, 5.3L, 6.0L Engines

Hope this help (remember rated the post).

Mar 26, 2010 | 2001 Chevrolet Blazer

Not finding what you are looking for?
2008 Suzuki XL7 Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...