Question about Cars & Trucks

1 Answer

How to replace sensor - Cars & Trucks

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Wen replacin the tp sensor on a 93 town cr is there a certiain way to put in in place

Posted on May 07, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate camshaft sensor 2008 3.6l malibu


Which one ?
Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake

Sep 02, 2016 | 2008 Chevrolet Malibu

1 Answer

Replace camshaft position sensor ?


need more information since each manufacturer puts the sensor in different spots --generic answer --the following link shows different vehicles sensors being replaced
How to replace camshaft position sensor in your vehicle Camshaft Position Sensor Replacement Replace Camshaft Position Sensor Yahoo Video Search Results

Aug 31, 2016 | Cars & Trucks

1 Answer

How to remove and replace boost pressure sensor, I realy want to know I want to replace mine.


Removal procedure
1.Disconnect harness assembly[1] from boost pressure sensor[2]
2.remove bolts[3] from boost pressure sensor [2]
3.Remove boost pressure sensor [2] from inlet manifold[5]
4.Remove O-ring seal [5]
Installation procedure:
1.Clean and replace worn out components.
2.Install a new O-ring 5 to boost pressure sensor [2]
3.Install boost pressure sensor [2] to to inlet manifold [5]
4.Install bolts[3] to to pressure sensor [2] finger tight.
5.Connect harness assembly[1] to boost pressure sensor[2]

Jul 23, 2016 | Cars & Trucks

1 Answer

How many o2 sensore are on the 99 bravado? I replaced the o2 sensor before the cat converter, now code says bank one( before cat.) needs replacing. are there 4?


the sensor before the cat is NOT an O2 sensor but a HO2S sensor ( two different sensors with different operations). If this is a V6 engine there are 4 sensors -- 2 --HO2S sensors before the cats --one for each bank cat and 2 O2 sensors after the cats.
The fault code would have spelt out the correct sensor for replacing

Jan 24, 2015 | 1999 Oldsmobile Bravada

1 Answer

My car is misfiring


I own a 2000 avalon and had a similar issue, rough idle especially when stopped, car felt like it was going to stall. I had a couple error codes which included one of the o2 sensors and knock sensors. I replaced the pcv valve , and o2 sensor, both easy fixes, but tue knock sensor is in the top half of the engine. Cost me 500 bucks to replace, install knock sensor at shop. After knock sensor was replaced and other o2 sensor replaced, no more idle issues. What happens if an o2 sensor on one of

Mar 02, 2014 | 2000 Toyota Avalon

2 Answers

O2 sensor won't stop coming on.. All are replace but the bank2 sensor 2 keeps coming back on.. That sensor was replaced with OEM sensor but it's saying there high voltage as well.. Please help!!


The problem is not the o2 sensor.

-Check for misfire. (some partial fuel is not completly burn, so it go
pass the sensor) Tha's why it keep sending signal.

Mai

Apr 03, 2013 | Cars & Trucks

2 Answers

Where is iat sensor located on 2000 mazda mpv van . i have a p0113 code and cant find sensor


the IAT sensor is part of the Mass Airflow sensor. here is a picture of that sensor.

5787058.jpg

Dec 16, 2009 | 2000 Mazda MPV

1 Answer

Knock engine sensor light on truck is hesitating/


Did they replace the knock sensor?Check the wire going to the sensor(knock).Look for a bare place hiting up against something ,grounding it out.Make sure the plug to knock sensor is good.And make sure it is making a good connection,Knock sensors also ground a part of the computer to feed back imformation.This connection is a must,the truck will not perform at all,stumble,miss,and carry on.Sometimes even backfire.If they did not replace the knock sensor,replace it with high quality sensor from NAPA,or oem from dealer.This sensor has to be made perfect,no room for inperfection.The knock sensor is easy to replace,they just screw in a hole in the block.When removing the sensors,nothing will come out such as oil or water,this is a dry threaded hole.It is a bell shaped sensor.If you don`t know which sensor is bad,purchase one.replace one,and if there is no change,replace the other side with the old sensor you just took out,it will be a good one.I hope this helps you,Let us know if it does.

Oct 05, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,679 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...