Question about 1991 Isuzu Pickup

1 Answer

02 light on for 90000 dealer check. need to turn off

Need to turn off o2 sensor light on 1991 isuzu pickup. i have dash out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

In the back of the instrument panel, there is a small screw next to an empty hole. Remove the screw and put it in the empty hole. Repeat this every 90,000.

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

02 sensor light stays on after installing new one, now what?


The O2 sensor automatically comes on after so many miles, doesn't even have to be bad. You have to take the dash down and there is a tiny little screw that you need to move. The light will go out, but it will.still work. It's been awhile since I did this, but I believe it almost directly below it.

Sep 22, 2012 | 1993 Isuzu Trooper

1 Answer

2002 toyota tacoma with a p1135 code and a # 4 cylinder misfire


I have had a problem like that on my Isuzu Rodeo Turns out the o2 sensor was bad. The computer reads it as not enough fuel. The mass airflow sensor will dump more fuel causing the engine miss fire.
You might check the codes again and see if you get the code for the 02 sensor. If so you can try to unplug the 02 sensor, the ck engine light will remain on, however the car should run without any issues.
Good Luck!!

Feb 21, 2011 | Toyota Tacoma Cars & Trucks

2 Answers

I have a 1991 Iuszu pickup the o2 light came on and I changed the o2 senor but the light never went out


disconnect the battery cable then turn on ignition turn igniton back off reattach cable and go start truck i bet light goes off have to reset it

Dec 11, 2010 | 1991 Isuzu Pickup

1 Answer

1991 isuzu rodeo o2 dash light is stuck on


The O2 sensor needs to be replaced. There is a screw on the back side of the instrument panel that is removed and switched to another hole in the circuit board to reset the light for another 90,000 miles. Only a shop manual will have the exact location. You can try and obtain one from http://www.helm.com and buy one using print on demand.

May 19, 2010 | 1991 Isuzu Rodeo

1 Answer

Need to change O2 sensor check engine light wont go off


Did you change the 02 sensor? The back one after the converter? If so, stop by a dealer, it may need to be reset.The back 02 is the one that trips the light. Keep that in mind.

Nov 09, 2009 | 2003 Toyota Corolla

1 Answer

How many fuel filters are in 1992 trooper 5 speed


what is a o2 light ? sounds like you need to take it to a shop and have some one check it out and stop trying to throw parts at it . sounds like tun up proublems and maybe the check egin lights on because one or more sensors have a proublem

Jul 08, 2009 | 1992 Isuzu Trooper

1 Answer

Cant find o2 sensors


if you follow your exhaust system you will find the o2 sensors they could have one right off the exhaust manifold and your second o2 is going to be behind the catalytic converter. so you will have a o2sensor before and after the catalytic converter on the exhaust hope this helps you out.
please rate me if you would
thank you
Aaron

May 22, 2009 | 1991 Isuzu Trooper

1 Answer

1991 Isuzu PickupTruck will start but wont continue to run


check wires under dash & hood .check fueses & relayes sounds like u have a short !!!

Feb 15, 2009 | 1991 Isuzu Pickup

1 Answer

O2 sensor


There should be a reset switch that turns the light off. Some vehicles require a code scanner tool to reset the check engine light. On some Isuzu models you have to remove the instrument cluster and move a screw from one hole marked KSW to another hole with the same KSW marking (it may have tape over the second screw hole). Other Isuzu models may have a small switch on teh back of the instrument cluster or may have a different marking on the screw holes (some were marked wit the letter B on both holes). The O2 light usually comes on at 90,000 mile increments which is when Isuzu recommends changing it.

Jun 12, 2008 | 1993 Isuzu Rodeo

Not finding what you are looking for?
1991 Isuzu Pickup Logo

Related Topics:

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...