Question about Cars & Trucks

Open Question

Toyota hi ace manual

Loose diff pinion bearing

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22114 Answers

SOURCE: Rear diff pinion seal replacement, preload torque

just yank it up tight with a bar about 50cms long,their should be collapsable spacer between the taper bearings just tighten it like a professional without overtightening it so and shearing something .handfull of grease in the diff casing to slow/stop any oil leaks top up with ep 90 and away you go,the crownwheel to pinion setting is just a little wiggle woggle ,or you could use a dial gauge but its quicker and easier ,too tight and it whines and too much play and it clunks,nice little wiggle woggle and it will work fine .trust me

Posted on Nov 13, 2008

  • 12 Answers

SOURCE: bearing or diff stranger sound

change the diff to be on the safe side

Posted on Feb 28, 2009

rick_amick
  • 69 Answers

SOURCE: pinion bearing

Have you checked the fluid level in the rear end. If it is the low the pinion bearing will not be getting lubricated.

Posted on Mar 21, 2009

thunderz
  • 232 Answers

SOURCE: My rear diff is whining.

Could be the pinion gear ,,Has it been leaking rear end oil? How many miles on this?Probly over a 100k? its old enough for it to start wearing out.Try changeing the rear end oil use Lucas.

Posted on Mar 11, 2011

Testimonial: "its done over 280 k and no oil leaks that I can see but that is very helpful thank u. I think u r right. I'll try it . . ."

perkins48
  • 14333 Answers

SOURCE: hi need to replace bearings on my rav4 96 model diff do i need to replace the collapseble spacers as well and what is the clearance settings on crown wheel and pinion

http://www.oreillyauto.com/site/c/search/Repair+Manual+-+General/03501/C0008.oap?model=RAV4&vi=1278301&year=1996&make=Toyota Here's a couple of repair manuals,always good to have one so you can trouble shoot on the spot.

Posted on Sep 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the layout in a diff of a Mahindra bolero DC? Mine's pinion bearing is gone I suppose because it is making a screetching noise. There is no play though between the propshaft and the pinion.


all diffs are constructed the same
check if there is any oil in the diff
if a bearing was faulty on the pinion , you will have movement at the pinion flange up/down /in/out
if you have a center bearing in the drive shaft , consider that the bearing has failed there producing the noise

May 03, 2017 | Mahindra Cars & Trucks

1 Answer

BA Falcon m86 v8 limited slip diff torque specs for full overhaul , and change of ratio. Can't find any help through ford at all.


all differentials are all set to the same specifications as to pinion bearing preload , carrier bearing preloads and back lash between the crown wheel and pinion
the contact pattern is always the same as is the torque measurement of the drown wheel to carrier bolts
so any workshop manual that has a differential repair section will have what you want
find yourself a ford workshop manual and follow the section as to rebuilding a diff
Note --the pinion will have a + or - measurement on the end and that denotes the thickness of the spacer under the pinion between the pinion and the bearing inner race
you will have to get that right or the contact pattern will be out
3.7 ration is in utes or station wagons so it may be simpler to get one out of that vehicle and re-race it as all you will need then is new bearings and a collapsable spacer and a good tension wrench and a spring balance to get the pinion bearing preload correct

Feb 22, 2017 | Ford Cars & Trucks

1 Answer

Min./max backlash required on diff for Isuzu KB280DT 1998model after reconditioning & prior to "running in"


around .005" -.010" measured at the crown wheel tooth
if you have back lash at the pinion yoke , that is not the backlash you need to measure as it is a combination of axle spline and side gear clearance in the diff
what is most important is the mesh position of the crown wheel and pinion teeth, preload on the pinion bearings and diff carrier bearings
you will need a workshop manual to get the correct mesh setting and preload readings

Dec 28, 2016 | Isuzu Cars & Trucks

1 Answer

Front diff.seal leaks


Remove the front drive shaft remove the drive yoke off the pinion shaft remove the old seal install new seal install front drive shaft. PS check pinion bearing play before removing drive yolk. if it is loose then you might also need bearings

Oct 21, 2015 | Ford Explorer Cars & Trucks

1 Answer

How to replace pinion bearing 99 dodge ram


If its a 4x4 remove rear drive shaft from vehicle, remove large nut (pinion nut) at front of diff which is generally hidden when driveshaft is in place. with a bearing puller remove pinion bearing replace with new one, install new pinion seal reinstall pinion cover and pinion nut tighten to specified torgue reinstall driveshaft check diff oil for proper amount

May 31, 2014 | 1999 Dodge Ram

2 Answers

I have replaced bearing on the pinion and crown on nissan 3.2. its has a bad noise. how do i adjust pinion and crown?


Adjustment to crown wheel and pinion has to be done after bearing replacement on the pinion and carrier. It is a method that unless you have done a lot of diff repairs will amount to a trial and error procedure to get it right. Fortunately any work shop manual that you can borrow will have the way to set up the diff and there will be photos and directions on which to move to get the setting right. It is important to get the reading right as correct gear mesh will ensure a long lasting quite diff operation.

Feb 08, 2014 | 2005 Volkswagen Golf 4

1 Answer

I have fit new bearing on pinion and crown but diff is noisy. how do i adjust to stop the noise?


REAR END SPECIALIST..THE BEARING IS COMING OF THE PINION SHAFT AND HAS TO BE DRIVEN BACK ON AND SEALED SO IT WILL NOT SLIDE BACK OFF.. HAD SAME ISSUE.. COST AROUND 200.. ALSO MAKE SURE TO GET POSTIVE TRACK DIFF. ADDIVTIVE.

Feb 08, 2014 | 1991 Ford F250

1 Answer

Front and back berring dissassembly of differential 2001 dodge 1500


For the rear diff., remove the driveshaft, brake drums, diff. cover, remove pinion flange nut, move diff carrier to access side gear retainer bolt and remove bolt, slide side gear pin out and push axles in to remove axle retainers and remove axels. Mark carrier bearing retainers, spin bearing retainers to loosen carrier for removal. Remove carrier, remove pinion out of diff case, then r&r bearings. Any shims should be replaced in their original location for depth and pinion to ring contact.

Feb 05, 2011 | 2001 Dodge Ram 2500 Truck

1 Answer

Rear diff pinion seal replacement, preload torque


just yank it up tight with a bar about 50cms long,their should be collapsable spacer between the taper bearings just tighten it like a professional without overtightening it so and shearing something .handfull of grease in the diff casing to slow/stop any oil leaks top up with ep 90 and away you go,the crownwheel to pinion setting is just a little wiggle woggle ,or you could use a dial gauge but its quicker and easier ,too tight and it whines and too much play and it clunks,nice little wiggle woggle and it will work fine .trust me

Nov 13, 2008 | 1990 Toyota Celica

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...