Question about Cars & Trucks

Open Question

3vze fuel return line location - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location on fuel pressure regulator for a 2006 buick rendezous cxl suv


It should be on the fuel rail next to the fuel return line. some new cars have in tank fuel filter and pump and the regulator is in the fuel filter housing and there is no fuel return line.

Apr 03, 2017 | 2006 Buick Rendezvous

1 Answer

Where are the fuel feed and fuel return for the injection system located?


They both run together from the tank up to the engine. They are both connected into the fuel rail on top of the engine. Sometimes the feed line is slightly bigger than the return line, or the feed line will be the one with the fuel filter in it.

Aug 29, 2013 | 1993 Geo Prizm

1 Answer

Where are the fuel lines located (primary/return) on a 2003 honda accord ex in the engine area


find your fuel rail and check at both ends, should see lines going in 1 end and 1 at other end of fuel rail, also you can follow lines from fuel tank to engine area

Sep 03, 2012 | Cars & Trucks

1 Answer

I can't find where the return line on the fuel system is going. only 1 line comes up to the front where the mechanical fuel pump is located. I can't get fuel to the carb.


on a carcureted engine there is no return line, to check fuel delivery disconnect the fuel line at the carb and turn the engine over, these run at low pressure, like 4lbs

Nov 19, 2010 | 1985 Pontiac Parisienne

1 Answer

Where is the fuel filter located on a 94 ford ecoline 150 van


If it is in the stock location it is in the largest of the three lines that come out of the fuel tank. Trace the fuel fill tube from the fuel cap to the tank. Look around the tank for the three lines. The largest is fuel out to the engine. The filter will be in that line. The others are the fuel return line and the line to the carbon canister.

Jun 10, 2010 | Cars & Trucks

2 Answers

Where is the fuel filter located on a 95 geo metro


1995 Geo Metro 1.3L TBI SOHC 4cyl
The Fuel Filter is located under vehicle, driver side, below seating area, driver side of transmission, mounted on frame rail in fuel line

1995 Geo Metro 1.0L TBI SOHC 3cyl
The Fuel Filter is located under vehicle, driver side, below seating area, driver side of transmission, mounted on frame rail in fuel line

Hope this help (remember rated and comment this).

Mar 23, 2010 | 1995 Geo Metro

1 Answer

3vze v6 engine no power to fuel pump can only


remove the passenger side of your dash "the glove box" there is a circuit opening relay tucked up behind the speaker it's small box. it reseavs signal from efi and maf then sends power to your pump. good luck...peace and love for all...

Jan 22, 2010 | 1994 Toyota 4Runner

2 Answers

Finding were a filter is


On these vehicles, the fuel filter is located on the fuel line to the carburetor. Special care should be taken when removing and installing the fuel filter, not to bend or distort the fuel line in any way.
  1. Remove gas cap to relieve any pressure that may be present in the fuel system.
  2. Remove the air cleaner bonnet assembly.
  3. Using a backup wrench on the return line fitting on the top of the fuel filter, remove the fuel line with a flare nut wrench.
  4. Using a backup wrench on the fuel filter inlet fitting, remove the fuel line from the fuel filter with a flare nut wrench.
  5. Using a backup wrench on the fuel filter outlet fitting, loosen the fuel line and remove the fuel filter from the engine with a flare nut wrench.
To Install:
  1. Apply a drop of engine oil to all the fuel line nuts and flared ends.
  2. Position the fuel filter with flow arrow on the filter directed towards the fuel line going to the carburetor.
  3. Finger-tighten the fittings at the fuel filter outlet, inlet and return line into the top of the filter.
  4. Using a backup wrench on the fuel filter fittings, tighten the fuel lines in the following sequence:
    1. Tighten the outlet and inlet line nuts to 15-18 ft. lbs. (20.0-24.0 Nm)
    2. Tighten the nut on the return line at the top of the filter to 6-9 ft. lbs. (15-18 Nm).
  5. Inspect the fuel lines and carefully adjust if they are interfering with the carburetor, air pump, or fuel filter housing.
  6. Start the engine and check for fuel leaks at all the connections. Retighten if necessary.
  7. If removed, install the air filter bonnet assembly.
0900c1528005d3e1.gif 0900c1528005d3e3.gif

Jul 26, 2008 | 1993 Ford Tempo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...