Question about 2000 Isuzu Rodeo

3 Answers

My instrument panel does'nt light up when I turn on my head lights and the radio light turns off and as soon as I turn off my head lights the radio light comes back on.

Instrument panel short. When I turn on my head lights the instrument panel does'nt light up and the audio radio light shuts off.

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,623 Answers

Hello manchie...You should have a dash light dimmer switch..remove it from the dash. There should be a 3 wire plug on the back side with a Red/Green, Green/red and black wire. Jump between the Red/Green wire and the black wire and see if the lights come on. If they do, it probably has a bad illumination controller.
Good luck and i hope this will fixya up.

Posted on May 20, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 36 Answers

First the obivious, when you turn on the lights, are you also rotating the nob, Im not kidding. They are reostats, variable resistors. If thats not the problem then im affraid you have a short. Some where a wire is bare and is touching the frame or another wire. Before you spend money make sure any and all ground wires are tight to the frame. Youll see they will just be wires fixed to the frame . Good Luck

Posted on May 20, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Isuzu Master
  • 2,007 Answers

Is there a dimmer switch for your dash lights? A dial thing, or a knob that you turn, maybe even on the switch itself? Turn it to see if thats the problem. You may have turned it by accident.

Posted on May 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 cavalier dash lights not working. all fuses are goood. replaced cluster, dimmer switch, multifunction switch


Back lighting or warning lights ? check engine , ABS , air bags , seat belt , oil light etc... ?
Interior Lamps Dimming
The second group includes lamps which may be dimmed. This group may use a combination of vacuum fluorescent (VF) illumination and incandescent lamps.
• Power window switches
• HVAC control head assembly
• Radio
• The instrument panel cluster (IPC)
When the ignition switch is turned to the ON position, the vacuum fluorescent (VF) display (radio) turns on at maximum brightness. When the park lamps are ON all incandescent back lighting turn ON at the dimming level indicated by the IP dimmer switch. At the same time all vacuum fluorescent (VF) displays dim to match the indicated dimming level. When the headlamp switch is placed in the PARK position, the park lamp supply voltage circuit provides an input to the body control module (BCM). The BCM then supplies voltage to the instrument panel dimmer switch through the instrument panel dimming lamps control circuit. The setting of the instrument panel dimmer switch determines the amount of voltage that the instrument panel dimmer switch supplies to the BCM through the instrument panel dimming lamps low reference circuit. The BCM then sends a pulse width modulated (PWM) voltage to all the interior lamps. All the vacuum florescent (VF) and incandescent back lighting lamps are provided a specific voltage and are then grounded. When the headlight switch is turned to the PARK or HEADLAMP position, all incandescent back lighting turn on at the dimming level indicated by the IP dimmer switch. When the IP dimmer switch is moved from MIN to MAX, all vacuum fluorescent (VF) displays, as well as all incandescent back lighting respond from Minimum intensity to maximum brightness in response to the IP dimmer switch.

I would have it checked for DTC'S - diagnostic trouble codes stored in the BCM !
DTC B2624 Display Dimming Input Range/Performance
The body control module (BCM) supplies voltage to the instrument panel dimmer switch through the instrument panel dimmer switch signal circuit. The dimmer switch varies the voltage and returns the new voltage to the BCM through the dimmer switch signal return circuit. The BCM uses this voltage to determine the illumination level of the instrument panel lamps.

DTC B2625 Display Dimming Pulse Width Modulation (PWM) Output Circuit Range/Performance
The body control module (BCM) receives a variable voltage from the instrument panel (I/P) lamp dimmer switch. The BCM uses this signal in order to vary the illumination level of the I/P lamps. The I/P dimming lamps output from the BCM is a pulse width modulated voltage supply used to light the I/P lamps. If a malfunction occurs in the I/P dimming lamps output circuit, this DTC is set.

DTC B2662 Park Lamp Switch Circuit Malfunction
The park lamps are controlled by the turn/headlamp switch. Positive battery voltage is supplied to the switch through the EXT LP fuse. When the turn/headlamp switch is placed in the park or head position, battery voltage is supplied to the park lamps. The body control module (BCM) is also connected to the park lamp circuit to sense whether or not the park lamps turn ON when the low beam or high beam headlamps are turned ON. The BCM also uses the parklamp battery positive voltage to power the instrument panel (I/P) dimmer output circuit. If the BCM senses that the low beam or high beam headlamps are ON and the park lamp input is not active, DTC B2662 sets.
Do the park lamps work ?

Jun 11, 2017 | Cars & Trucks

1 Answer

I need to know what controls the lights that illuminate the radio and heater controls on a 1998 Cadillac Seville. the displays are working. Just not the buttons on each are not lit


head light switch make sure you don't have the instrument panel dimmed all the way down if so turn it up, then if that doesnt work make sure your head lights are turning on when they are suposed to, if not you may have a bad light sensor on the dash or bad headlamp switch.

Feb 24, 2015 | 1998 Cadillac Seville

1 Answer

Why do the instrument panel lights turn off when I turn on the headlamps?


Head light switch controls the brightness of the dash lights. Looks like it's the problem.

Aug 27, 2014 | 2002 GMC Yukon Denali

1 Answer

How to replace light bulb on a clock 2004 Honda Odessey


Here are the steps:

1. Undo the panels to the left and right of the steering column.
2. Remove the panel that encloses the instrument cluster.
3. Replace the light bulb located on the back of the panel (removed in step 2).
4. Reinstall the instrument panel (removed in step 2).
5. Reinstall the panels on the left and right of the steering column.

Here are the details:

FIRST - Disconnect the battery. Be careful to locate the radio security code and radio station memory locations before you disconnect though. I chose to disconnect the ground (black wire) from the battery. Be careful to put the cable away from the battery terminal.



Step 1: Undo the panels to the left and right of the steering column.
a. Put on your parking break. You'll want to prevent the car from moving because you will soon put the car in gear.
b. Put your keys and turn to the starting position (but don't try to start the car). This allows the gear lever to move.
c. Move the gear shift to lowest gear. This puts the gear shift lever to a place nearly out of the way of the panel so that you can pry it out.
d. Using bare hands, pull smartly on the plastic edge closest to the steering wheel. Pry out the panels by hand as they are both held by tabs. This is hardest to do the first time. Keep in mind that these are pieces of plastic, so be careful. Once panels are out, let them dangle. You only need access to the instrument panel screws.

Step 2: Remove the panel that encloses the instrument cluster.
e. Remove the 8 screws that keep the instrument cluster panel in place.
o Two on left of steering wheel
o Two on top of instrument cluster (upside-down)
o Four on right side of steering wheel
f. Wiggle/pry out the instrument cluster panel. Be careful as the center is held in stronger than the sides. In addition to screws, there are different tabs that assist in holding this in place.
g. Before removing the instrument cluster panel, disconnect the clock and emergency light electrical connectors. While the clock connector disconnects easily, the emergency light has a locking tab that needs to be pushed in to disconnect. I used a small screwdriver to push in the tab to get the connector to disconnect.
h. Remove the instrument panel. Turn it over and locate the clock's protective cover.
i. Open the clock's protective cover by loosening the tabs. Be very gentle to these tabs.
j. Once the cover is removed locate the light bulb.

Step 3: Replace the light bulb located on the back of the panel (removed in step 2).
k. Unscrew the light bulb and remove.
l. Install the new light bulb. Check the light bulb before you install it. Be careful when rotating the new light bulb. in place. I've read in other posts that the light bulbs are VERY sensitive. I used a small screwdriver with plastic on the head to screw the light bulb. in.
m. Replace the clock's protective cover.
o. Reconnect the clock and emergency light's electrical connectors.

Step 4. Reinstall the instrument panel (removed in step 2).
p. Fit the instrument cluster panel back into it's original position. Be careful with the fan vents. I suggest aligning the fan vents first, then fitting the panel.
q. Screw in the 8 screws that keep the instrument cluster panel in place.

Step 5. Reinstall the panels on the left and right of the steering column.
r. Push both panels back into place.
s. Move the gear shift lever back to park.
t. Remove the car key.
u. [Optional - disengage the parking brake]

LAST - Reconnect the battery.

TEST - Reinsert your keys and turn them to the starting position (but don't start the car). The clock light should light up.

Note: Because the power has been reset, you will need to enter the factory stereo code and reset your radio stations.

May 25, 2011 | 2004 Honda Odyssey

1 Answer

Fuses panel described in English


Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn jlmacman.png jlmacman_0.png

Inside kick panel jlmacman_1.png

Mar 07, 2011 | 1995 Kia Sephia

1 Answer

When I turn my lights on, the two turn signals stay on and none of the dash lights come on. The turn signals flash when you flip the lever left to right so i know the problem is not in the blinkers or...


sounds like an open to the lights in the instrument panel, if the lights work in the radio, ac panel, etc.

Or, all the bulbs burnt out at once (unlikely).

Maybe the harness to the instrument panel is loose, but only is accessible after removing the dash board.

Jul 11, 2010 | 2000 Ford Taurus

1 Answer

Dash and shifter lights in 1996 jeep cherokee wont light


Hello and welcome to FixYa . Locate the dial that controls the brightness of the dashboardlights. If the control is not immediately evident. Make sure the brightness control is turned on. If it is and the lights aren't working, the problem may be a bad fuse. Check the fuse that controls the dashboard lights Replace the fuse if necessary. If just one part of the instrument panel is not lighting up, then you have either a burned-out bulb or a wiring problem.

Passenger side kick panel fuse breakdown for a 1996 jeep Cherokee Country

01 - 25A Rear Wiper/Washer
02 - 15A Radio, Cigar Lighter
03 - Empty
04 - 15A Passing Light
05 - 30A Blower Motor
06 - 30A (Circuit Breaker) Power Windows
07 - 02A ABS
08 - 20A Turn Signal Flasher
09 - 10A Radio/Clock Memory, Courtesy Lights, Glove Box, Cargo, Dome Lights, Telltales
10 - Empty
11 - 25A Headlamp Delay Module, Horn
12 - Empty
13 - 20A Power Door Locks
14 - Empty
15 - 15A Instrument Panel Lamps, Clock/Radio and Memory, Headlamp Switch, Parking Lamps
16 - 30A (Circuit Breaker) Power Seats, Trailer Tow
17 - 7.5A Instrument Cluster Gauges, Headlamp Delay Module, Chime Module, Overhead Console
18 - 25A Rear Defrost
19 - 05A Instrument Panel Lamps, Radio Illumination
20 - 5.5A (Circuit Breaker) Windshield Wipers and Washers

This should get you going. And you can always Ask Me.

Apr 27, 2009 | 1996 Jeep Grand Cherokee

1 Answer

No instrument panel lights on a 2003 chevy monte carlo


Most likely this is caused by either the dimmer being turned off (happens all the time on my Corvette) or the dimmer is defective.

Nov 30, 2008 | 2002 Chevrolet Monte Carlo

2 Answers

Radio wiring


The factory wiring connector hook-up for the Mustang is:

Radio / Power Connector:

Light Green / Yellow - Hot at all times (Fuse 8)
Yellow / Black - Hot in ACC or Run (Fuse 11)
Light Brown / Red - Goes to instrument panel dimming rheostat (Fuse 4)
Red - Ground
White / Purple - Hot in ACC or Run (Fuse 11)

Speaker Connector:

White / Light Green - (+) Right Instrument Panel & Door Speaker
Dark Green / Orange - (-) Right Instrument Panel & Door Speaker
Brown / Pink - (+) Right Rear Speaker
Pink / Light Brown - (-) Right Rear Speaker
Pink / Light Green - (+) Left Rear Speaker
Tan / Yellow - (-) Left Rear Speaker
Light Brown / White - (+) Left Instrument Panel & Door Speaker
Orange / Light Green - (-) Left Instrument Panel & Door Speaker

Your best bet is to buy a radio install kit and adapt it to the Mustang connector. Hope this information helps.

Oct 19, 2008 | 2002 Ford F250 Super Duty SuperCab

2 Answers

Tail Lights, Marker Lights, Air Conditioner lights out


it seems to be a wiring problem .get the wiring checked.

May 22, 2008 | 2005 Pontiac Vibe

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...