Question about 2008 Honda Accord

Open Question

B1235 What does code mean especially the 5

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have several A/C error codes: B1234, B1235, B1459, B1231. What are they, and what parts bo I need to replace?

perhaps you need to call a mechanic since we need make /model/year etc to look for possibly problems

Apr 23, 2015 | Cars & Trucks

1 Answer

1987 reliant le 2.5 my trouble codes are , 1.2 , 1.3, 5.5 what does this mean?

Been a long time since I have seen one of these on the road............. I used to own one.

Code 1.2 means that the battery has been disconnected recenty (or died)
Code 5.5 means it is the end of the codes.

However Code 13, or 1.3 as you state............. is a MAP sensor code. These vehicles are notorious for MAP sensor Issues.

First inspect the vacuum hose for cracks or breaks, I suggest replacing it anyway because the car will barely run without it. If the vacuum hose does not help, make sure the sensor is actually getting vacuum from the engine in-case it is clogged. If it is them remove the electrical connector from the MAP sensor with the key ON but the Engine OFF. Use a volt meter to check that one of the pins has about 12 volts, another should have 5 volts, and the last should have Ground. if these are ok then you will need a new MAP sensor.

Oct 19, 2014 | 1987 Plymouth Reliant

1 Answer

2003 VW Jetta Codes

i have a land rover freelander how does an engine how does engine coil goes bad? also I'm having another problems with my rear windows they don't want to go up or down. I changed the sensors but still not working. can you please help me

Nov 13, 2013 | Volkswagen Cars & Trucks

2 Answers

What does codes b1233,b1235,b1236,b1185,b1198,b1194,b1254,b1246,b1250,b1242,b1214,b1210,b1446,u1262,p0171,p0174 is

When you have a list of codes like that, it is usually due to charging system problems (computers doo all kinds of crazy things when they are getting delirious from malnutrition). I would be performing a THOROUGH check of your battery and charging system before doing anything else to try to diagnose this problem.

May 25, 2012 | 2003 Ford Windstar

2 Answers

Flashing SES, P0305, and P1145

A flashing SES light means that you are operating the vehicle under conditions that are DESTROYING your catalytic converters! This is not good.

Diagnostic Test Code (DTC) P0305 is defined by SAE J2012 as "Cylinder 5 Misfire Detected".

DTC P1145 is a "manufacturer-specific code" and is defined by Nissan as "Bank 2 Intake Valve Timing Control Position Sensor - High Or Low Voltage"

So, to put it simply, you need to find out WHY cylinder #5 is misfiring and get it fixed. You also need to diagnose the intake valve timing control position sensor circuits on bank 2 to (1) find out if the voltage is HIGHER or LOWER than specification (since the code itself is not specific about which it is). And (2) find out what is CAUSING the voltage to be out of specification and take the appropriate action correct it.

Apr 27, 2012 | 2002 Nissan Pathfinder

2 Answers

My dodge caravan 3.3L shows 5 malfunction codes what do they mean po455 po846 po500 po700 po732

P0455 = Evap leak monitor large leak detected.
This code usually means the gas cap may have been loose or needs the rubber gasket.

P0500 = No vehicle speed sensor signal.
Vehicle speed sensor is located on the transmission near one of the axle shafts (it may need replacing).

P0700 = EATX controller DTC present.
This simply means you have transmission related codes.

P0732 = Gear ratio error in 2nd gear.
This code is of some concern, it means the transmission is slipping in 2nd gear. However the trans may be in limp mode due to the speed sensor code (limp mode means the trans starts out in second gear in order to at least get to a mechanic). The first thing I would do is have these codes cleared as there may be absolutely nothing wrong with the transmission (especially if you pull the trans dip stick and the fluid does not have a burnt smell. The vehicle should drive normally after that. If the check engine light comes back, have the codes scanned ASAP (before any other unrelated code sets). Chances are it may be the output speed sensor if this happens (easy fix). Hope this helps


Oct 26, 2011 | 2002 Dodge Grand Caravan

1 Answer

What does B1234, B1236, B1235, B1233 mean for a Lincoln Ls

B1233 - Glass Break Sensor Failure
B1234 - Mirror Switch Invalid Code
B1235 - Window Feedback Failure
B1236 - Window Feedback Loss of Signal

Sounds to me like the connector for the wiring harness from the body into the door has come unplugged. Am I right in guessing that you have at least one window that won't roll up or down and you can't adjust at least one of your electric mirrors (On the same side as the faulty window).

Drop me a comment back on here, let me know what you find and if I can assist further

Jul 22, 2011 | 2002 Lincoln LS

1 Answer

CHECK ENGINE LIGHT CODES B1235, B1236, B1234, P0128

go to obd codesii you can find descriptions there

Apr 18, 2011 | 2003 Ford Explorer

1 Answer

Engine light comes on and flashes 5 pause and then 1 wht it means?

on many vehicles especially a chrysler/dodge product, anytime the check engine light flashes is due to a misfire whether it be electrical or fuel related.check the coil, spark plug wires especially on the rear head towards the firewall , and spark plugs if tune up hasnt been done recently. hope that helped you!!

Jul 09, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2008 Honda Accord Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides