Question about 1992 Toyota Land Cruiser

1 Answer

Truck is misfiring ,and the rpm gauge is not moving, help pleaseeee

My truck is misfiring,how can it be fixed?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 2,007 Answers

Probably a loose tach wire. Look on your distributor for the wire, and disconncet it to see if the engine clears up.

Posted on May 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the rpm gauge jump up when the engine misfires


Engine revs to attempt to prevent stalling from misfire. Why not just fix misfire and be done?

May 07, 2015 | Cars & Trucks

1 Answer

I have a bad shudder or miss at 1500 rpm in my 2006 jeep commander it does it in 4th and 5th gear when it gets around 1500 rpm


that is engine misfire.
use a scan took see P03xx codes (DTC)
bingo.
get a tune up yet,
like filters and spark parts listed in the opr. guide? yet>

misfire has 50 causes, and about 10 tests with gauges/meters to find after doing a tune up,
spending 100/hr to do all those tests , that tune up cures, makes me rich, well did, im retired. LOL !!!!!

Mar 14, 2015 | 2006 Jeep Commander

1 Answer

Reasons for cylinder misfires


Ford coil on plug systems are multi strike ignition (spark) under 1300 rpm then go to single strike a single cylinder misfire can be created by several things . #1 Test engine compression on a cranking engine compression it should be around 150 lbs but if gauge reads different COMPARE to other cylinders that work fine #2 check engine running compression this will be around 120 lbs then rev over 2000 rpm and check pressure drop again COMPARE to other cylinders that work fine. any drop would indicate valve train problems. #3 All internal engine is fine then external problems are present vacuum leaks and or fuel injection volume is low.

Jul 23, 2014 | 2003 Ford Thunderbird

1 Answer

Rpm gauge doesnt work.


will be one of the fuses in the dash. also could be air in the line if you have that style rpm gauge.

Oct 27, 2013 | Subaru Cars & Trucks

1 Answer

The rpm gauge is not reading how it should.. how can i fix this?


In order to calculate your speed by the RPM gauge, you need to know your car's gear ratio, the diameter of your tires and what gear you are in. It would be safer to take your car into the shop and have the speedometer repaired. It is a relatively inexpensive repair and much better than a speeding ticket. ----------------------------------------------------------------------------
Car Key Programmers

Nov 19, 2012 | Cars & Trucks

1 Answer

2004 pontiac aztek speedometer will not go back to zero when stopped when speeometer maxes out will not move again and rpm gauge bottemed out and will not move


sounds like a short somewere for the rpm gauge as for the speedo it sounds like the cable could have broke or streched

Feb 27, 2011 | 2004 Pontiac Aztek

1 Answer

Replaced battery - RMP gage is reading 8 plus when car is not moving


There is a problem with the gauge cluster. There are little stepper motors that go bad. There is a place that sells them out of Michigan. 989-790-1911. You can either send them your gauge cluster or just buy the motor and have your electronics guy fix it.
The rpm gauge fails first because it moves the most. They will all stop working sooner or later.

Feb 14, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

2000 Astro Random Misfire


This sounds like a classic GM plugged catalytic converter symptom. If you like you could remove the oxygen sensor in front of the cat and try driving it. With the sensor removed, the exhaust can escape a little more easily and will drive better if the cat is the problem. If you have the right fitting and a gauge, you could actually measure the back pressure at the oxygen sensor hole. It should not be any higher than about 2 psi at 3000 rpm. I have seen this problem several times now on these vans and I'm almost certain this is your problem.
Hope this helps,
Dave

http://sun-transport.com/Automotive-Repair-Tools/Exhaust-Back-Pressure-Tester/

Apr 24, 2010 | 2000 Chevrolet Astro

Not finding what you are looking for?
1992 Toyota Land Cruiser Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...