Question about Cars & Trucks

Open Question

Hino 268 brake gets stuck with acceleration pedal

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: brake pedal stuck 1995 crown vic lx

did you bleed the brakes and get the air out of the lines and also if you have shoes on the back did you put the little shoe in the front and the largest in the back? and if you replaced the wheel cylinder or had any lines opened you have to bleed the brakes

Posted on Jan 16, 2009

Ad
  • 1348 Answers

SOURCE: my brake pedal gets stuck.

sounds like your master cylinder is bad.

Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E pops up on message center where it shows what gear you are in 2011 hino 268


Have the TCM module scanned for transmission fault codes, that is why the "E"

Jul 14, 2017 | Cars & Trucks

1 Answer

I had a hino truck 268 replaced the rear suspension bushings but still with vibration


MOST vibration in large trucks when driving are caused by u-joints or bend drive shafts

Oct 03, 2015 | Cars & Trucks

1 Answer

Where is the brake light switch located in a 1989 fd hino


If its a mechanical switch its on a bracket at the top of the brake pedal arm , if it is a pressure switch it located in the brake oil line near the master cylinder.

Mar 12, 2015 | Cars & Trucks

1 Answer

I have a hino truck 268 and recently the light level antifreeze start show ,the level is OK in the reservoir tank but inside the radiator is low what cause of this


you could have a leak in the system. get the system pressure tested and checked for leaks. if no leaks are found it could be burning coolant.

Nov 30, 2014 | Cars & Trucks

1 Answer

No brake lights on 2006 Hino 268 truck. Checked


cant get the pedal low enough to activate lights need to fix the power booster for the brake

Sep 16, 2014 | Cars & Trucks

1 Answer

Hino truckk13c engine start no accelerate plusing low power


run fault codes if it is set up that way . or if pre electronic check for air leaks in the fuel system . Check that the vent on the fuel tank is not blocked creating a vacuum in the system. Check that you are getting full throttle when the accelerator is fully depressed. With the engine stopped have some one press down on the pedal and you may be able to still move the lever on the pump . If so adjust the setting till it hits the stop. The accelerator cable may be one the way out and needs replacing

Nov 24, 2013 | Cars & Trucks

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.


code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

2 Answers

1992 Pontiac Bonneville. On acceleration up to 20 mph, the emergency brake light signal illuminates, beeping signal is heard as well. Verified emrg brake handle is retracted and brakes are off. When I...


Hello... I would recommend checking for a frozen (stuck) rear brake, a mis-adjusted emergency brake light switch, a stuck or sticking parking brake cable or a mis-adjusted brake pedal rachet lock which is the locking mechanism that holds down the brake pedal. Remember it could be multiple problems.

Good Luck..

Mike

Dec 29, 2009 | 1992 Pontiac Bonneville

2 Answers

Accelerator got stuck while passing a truck.


When you passed the truck... I guess you couldn't tell if the pedal was stuck since you were focused on braking.

When you brake, your brakes will overcome the acceleration of the car causing it to slow down, but like you describe, the second you let go of your brake, your car accelerates again.

It would sound like either the throttle pedal (gas pedal), the throttle line (connects pedal to throttle assembly) or your throttle assembly (on the engine) may be sticking....

Sep 03, 2009 | 2008 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...