Question about 2000 Ford Taurus

Open Question

2000 ford taurus key in ignition turns with no resistance and nothing happens except warning lights

Ignition key turns lock to start with total loose feeling back and forth

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: 2005 ford taurus. Remote entry wont work theft light keeps blinking when key is engaged

HI, I'm reading your problem,
Let me explain something about your car.

2005 Ford Taurus, The key on that car has Chip inside of the key and receiver on the ignition switch,
Check if the key you are trying to use is Black and has a plastic head.
If not you need a key with that characteristics.
But if you have the right key, Remenber if you had drop on the floor, or hit with something,
Because some times they come damaged, with insignificat thins.
Remenber if you left the key close to a magnets like speakers.

If nothing aply at your case, you need to call a place Aloha Smith, they have the computer to program or reprogarm your key. IF not you can't start your car.

OK.. I hope this information work for you.

Thank's for submit yous question on fixya.com

Posted on Jul 10, 2008

emissionwiz
  • 75822 Answers

SOURCE: 2003 Ford Taurus SES wont start and theft light blinking

most likely the fuel pump has failed, have the fuel pressure tested.

Posted on Jun 30, 2009

  • 1 Answer

SOURCE: stuck ignition cylinder 1992 ford taurus

It is not necessary to have the dealer do this, think of the cash! Though it does require patience and time. The pin you are supposed to push in goes into a slot when you have it in run position, since you cannot turn it to run you have to make a slot for the pin to go into, with a drill. Be very careful as you only have a 1/4" of play before you break a washer behind the cylinder. Once you have drilled out the key far enough to the pin hole you can take a nail set and tap the pin up, you can tell when the pin clears the housing, then it just takes wiggle, patience and tinkering to get the cylinder to slide out, keep the green washer and the metal slot washer. Metal slot washer goes in first with green plastic washer ontop of that with lock cylinder in last. You can play around with the new lock cylinder and washer before insertion to determin correct direction.

Here are official directions with inoperable lock cylinder. They say drill out retaining pin but it just spun in circles for me - I looked at new cylinder and saw how it worked. retaining pin needs a place to go.
Removal & Installation (Non-Functional)
NOTE:Use this procedure to remove ignition lock cylinder if key is missing or cylinder is frozen.

Disconnect negative battery cable. Disable air bag system. See appropriate AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS. Wait at least one minute for air bag back-up power supply to deplete. Remove steering wheel. See STEERING WHEEL . Using a 1/8" bit, drill out retaining pin located below lock cylinder on housing. DO NOT drill deeper than 1/2".
Using channel lock pliers, twist lock cylinder cap until it separates from lock cylinder. Using a 3/8" drill bit, drill down center of ignition lock key slot about 1 3/4" until lock cylinder breaks loose from its base.
Remove retainer, washer, and lock cylinder gear from housing. Remove metal shavings from lock cylinder bore. Replace housing if damaged. To install, reverse removal procedure. Connect negative battery cable. Check air bag system for proper system operation. See appropriate AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS.

Posted on Jul 12, 2009

rtpflh
  • 546 Answers

SOURCE: 1997 Ford Taurus ignition switch was jammed and

the ignition switch is located under the dash at the bottom of the steering column.suspect a fault in the linkage connecting tumbler to switch.

Posted on Oct 15, 2009

  • 407 Answers

SOURCE: 2000 Ford E350 Econoline, 5.4L. Won't start.

neutral safety switch also if the shifter handle is real loose the assm might be bad there known to break or the bushings to get warn out.

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Drove my 2000 Ford Mustang to the store, parked & locked it. Came back out 15 minutes later, unlocked it, got in & put my key in the ignition. The key & ignition switch turned all the way over with no...


Could be a bad battery or your battery cables could be loose or corroded so there is little power getting to the starter.Check all battery cables at both ends and might even have to take the cables off the battery and clean the connections hook up to the battery.

Jan 05, 2015 | 2000 Ford Mustang

1 Answer

Parking lights and dinger wont turn off when key is pulled from ignition on a 2004 ford taurus ses.


Not sure about the parking lights. But the warning chime is controlled by a sensor in the key lock.

Dec 11, 2012 | 2004 Ford Taurus

1 Answer

2000 ford taurus no ignition power


In the diagram, the top wires are voltage to ignition switch, hot all the time, use a test lite to check for voltage, you can see the wire colors. The bottom wires go hot with key in the proper position, check them for voltage, also. I started to trouble shoot your power windows, figuring if you fix one component, it may fix the others. I guess it's 6 of one or 1/2 dozen of another. Several ways to troubleshoot.
Any applicable trouble codes?
tarus ignition switch-digl1mhfajk5iowmjm3h1lij-4-0.jpg

Mar 15, 2017 | 2000 Ford Taurus

1 Answer

2000 ford taurus wont start. When the key is turned I have no dash lights, or power to the accessories that run through the ignition. I changed the ignition switch today. Thank You Chris


Is your dome light coming on? do the power locks work?
Your battery may be dead, or you may have blown a main fuse (under the hood)

Mar 09, 2011 | 2000 Ford Taurus

1 Answer

Help needed with starting problems. 1998 Ford Taurus SE. After driving the car for more than one hour the car will not re-start. I will turn the ignition key and nothing happen, all of the auxiliary...


Check the wire harness to the starter solenoid, the wires could have a break in it or the solenoid could also be bad. The heat of the engine could be causing the solenoid to fail till it cools down. Try that first, good luck and keep me posted, be glad to help.

Jun 15, 2009 | 2000 Ford Taurus

2 Answers

2005 ford taurus. Remote entry wont work theft light keeps blinking when key is engaged


HI, I'm reading your problem,
Let me explain something about your car.

2005 Ford Taurus, The key on that car has Chip inside of the key and receiver on the ignition switch,
Check if the key you are trying to use is Black and has a plastic head.
If not you need a key with that characteristics.
But if you have the right key, Remenber if you had drop on the floor, or hit with something,
Because some times they come damaged, with insignificat thins.
Remenber if you left the key close to a magnets like speakers.

If nothing aply at your case, you need to call a place Aloha Smith, they have the computer to program or reprogarm your key. IF not you can't start your car.

OK.. I hope this information work for you.

Thank's for submit yous question on fixya.com

Jul 10, 2008 | 2005 Ford Taurus

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...