Question about 1998 Toyota Sienna

1 Answer

How to install 3rd row dicki seat Ford 94 GLI ED

I have purchased a 2 seater ford universal dicki seat,I know my make of car had the option of 3rd row seating when it came of the assembly line, so i am wondering where and how to find the holes to bolt the 3rd row seat in. The petrol tank is located under the spare wheel bay in the back so i cannot drill holes, but i believe there would be holes under putty,both sides of wheel bay have putty all the way along.Any help will be appreciated i dont need instructions for seatbelts as they are attached to the seat all that needs to be done is 4 bolts to attach set to boot thankyou

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 293 Answers

These were normally mounted in the reverse position BUT the problem is your seat must be fitted by APPROVED installer because your car requires a Blue tag for a modified vehicle to make it legal to use. you install it you make your vehicle registration and insurance not valid and need to be reinspected for road worthiness before it is driven (don't feel bad because child restraint anchor points are the same, that is why in Australia we recommend Ambulance fitting centers)

Posted on Jan 01, 2014

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 2004 toyota highlander -

Most dealers will not perform this service, as they become the "final stage manufacturer", and what that means is THEY would be responsible for any claims (liability) that may arise from an accident. Toyota does NOT recommend adding seats, nor do they recommend changing seat types (buckets vs bench). Note that the vehicle is designed with the specific seating positions in mind. To add a 3rd row seat, you would also have to install the proper seatbelts, and secure the 3rd row seats in a fashion that meets NHTSA specifications.
In short, and I apologize for this, please refrain from doing it.

Posted on Sep 25, 2008

  • 98 Answers

SOURCE: Starter replacement - 1991 Toyota previa

Here are detailed, step-by-step instructions for the removal and re-installation of your starter motor. Hope this helps! Have a great day!

Starter Toyota Previa 1991-1997 Repair InformationREMOVAL & INSTALLATION
See Figures 5 through 12

  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front driveshaft.
  4. Remove the nut and disconnect the starter wire.
0900c15280089fbb.jpgFig. 5: Disengage the starter wiring
  1. Disconnect the starter connector.
0900c15280089fbc.jpgFig. 6: Remove the cap hiding the nut 0900c15280089fbd.jpgFig. 7: It will be necessary to use an extension to remove the nut
  1. Remove the bolt holding the starter stay to the upper stiffener plate.
  2. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  3. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
0900c15280089fbe.jpgFig. 8: Four bolts hold the starter in place 0900c15280089fbf.jpgFig. 9: The nut is located on the top of the starter 0900c15280089fc0.jpgFig. 10: Extract the starter from the engineTo install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc1.jpgFig. 11: Bolt locations on the 2WD models
  1. If equipped with 2WD, install the starter, nut and three bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc2.jpgFig. 12: Bolt locations on the 4WD models
  1. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  2. Install the starter connector.
  3. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  4. If equipped with 4WD, install the front driveshaft.
  5. Connect the negative battery cable.
SOLENOID REPLACEMENT
The starter solenoid (magnetic switch) is an integral part of the starter assembly.
  1. Remove the starter from the van. Remove the heat insulator from the starter assembly, if equipped.
  2. Disconnect the wire lead from the magnetic switch terminal.
  3. Remove the two long, through bolts holding the field frame to the magnetic switch. Pull out the field frame with the armature from the magnetic switch.
  4. Toseparate the starter housing from the magnetic switch assembly, remove the two screws and the starter housing with the pinion gear (1.6 kW), idler and clutch assembly.
To install:
  1. If necessary, install the gears and clutch assembly to the starter housing. Apply grease to the gear and clutch assemblies and place the clutch assembly, idler gear, bearing and pinion gear (1.6 kW) in the starter housing.
  2. Insert the spring into the clutch shaft hole and place the starter housing onto the magnetic switch. Install the two screws.
  3. Install the field frame with the armature onto the magnetic switch assembly and install the two through bolts. Tighten the bolts on the 1.4 kW to 52 inch lbs. (6 Nm) and on the 1.6 kW to 82 inch lbs. (9 Nm).
There is a protrusion or tab on each part; make sure you line them up correctly during assembly.
  1. Connect the wire to the terminal on the magnetic switch and tighten the nut to 52 inch lbs. (6 Nm). Install the heat insulator, if equipped.
  2. Reinstall the starter on the vehicle. Check starter system for proper operation.

Posted on Nov 23, 2008

  • 160 Answers

SOURCE: rear seatbelt

fold rear down take outter seat off one twelve bolt at bottom remove clps and pck tray YOU GOT IT

Posted on Mar 16, 2009

  • 318 Answers

SOURCE: The left side bolt on the driver's seat on my 2001

The recieving nut is welded to the car by the toyota factory. Just insert said bolt and screw.....

Posted on Jul 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove third row seats in 2001 Mitsubishi Chariot


same way as you slight the front seat forwart.lift the bar up underneed the seats

May 30, 2013 | 1998 Mercury Villager

1 Answer

Why is there no power to third row seat?


Power 3RD Row Seat Problems and Tranny Shutter - Ford Truck ...

www.ford-trucks.com > ... > Expedition & Navigator
Mar 27, 2014 - Expedition & Navigator 1997 - 2002 and 2003 - 2006 Ford Expedition andLincoln Navigator SPONSORED BY: ... First the 3RD row seats won't fold down, noclicking, no sounds, nothing. I the fuses are good and there is power at the fuse box, but no power at the motors or switches. Based on continuity ...

3rd row powerfold seat stuck down - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 2007 - 2014 Expedition & Navigator
Mar 14, 2010 - 3rd row powerfold seat stuck down 2007 - 2014 Expedition ... 2010, 2011, 2012, 2013 and 2014 Ford Expedition and Lincoln Navigator ... I also tried lifting the seat while my wife was pushing the button to raise it, to no effect. There is defnitelypower going to the motor but it just isn't ... Join Date: Feb 2005.

No power to third row seat on 2005 lincoln navigator - Fixya

www.fixya.com/cars/t12295627-no_power_third_row_seat_2005_lincoln
Apr 4, 2012 - no power to third row seat on 2005 lincoln navigator third row seat is ... U will have to replace the entire power seat transmission, there is no ...

Lincoln Navigator Review - Edmunds.com



Apr 04, 2012 | 2005 Lincoln Navigator

1 Answer

How are the middle row safety belts supposed to function properly? my used van is showing signs of character.


It depends on your seating. My Windstar has bucket seats, and the very back is a bench type 3 seater. The middle row normally has 2 shoulder/lap belts. It really depends on the perks that the original owner opted for upon purchase. For instance my driver seat has a button on the right side to adjust the lumbar area of the seat.
Checking CarFAX will let you know if the vehicle has ever been in a major accident. Most people do not realize that after an accident, seat belts and their anchors should be replaced.

Sep 23, 2010 | 2001 Ford Windstar

2 Answers

Does 2003 Ford Explorer have 3rd row seat


The third seat was an option on this model. Your model may or may not have the third seat. You should be able to tell by looking at the floor in the back. Ford may have included the rear cup holders on all models for ease of production.

Mar 10, 2010 | 2003 Ford Explorer

2 Answers

1999 ford expedition


1999 Expedition

Seats — Third Row
The third row seat is:
  • a three-passenger seat.
  • engaged to the floor by a latch and striker assembly.
  • a quick release seat.
  • equipped with rollers to ease removal and installation.

Dec 17, 2009 | 2002 Ford Expedition

1 Answer

Power Fold Rear 3rd Row Seat on 2006 Ford Explorer will not raise. I can hear motor trying to raise seat. The gear does not appear to be turning. Motor hums like it is in a bind. What needs replacing?


Power Fold Rear 3rd Row Seat on 2006 Ford Explorer will not raise. I can hear motor trying to raise seat. The gear does not appear to be turning. Motor hums like it is in a bind. What needs replacing?

Oct 19, 2009 | 2006 Ford Explorer

1 Answer

How do you remove the 3rd row seat on a 2002 ford expedition


remove seat to floor mounting bolts, then detach the seat and lift out of vehicle. install in reverse

Oct 15, 2009 | 2002 Ford Expedition

1 Answer

Lifting up whole 2nd row seats to access fuel filter


supposed to unlock with levers to fold back rest down,my 2000 nm has same prob I have to get large flat blade screwdriver or similarobject and get in back(stow rear dicky seat first)and lever the catches that lock base to floor not hard after you have done it once and seee how it works.hope this helps and works for you.

Apr 22, 2009 | Mitsubishi Passenger Cars & Trucks

1 Answer

Is it possible to put a 3 seater bench in second row


Yes...you can. I did this in my 05 Grand Caravan. We found ours at a local junk yard. It cost us 200 and even matched pretty well with the current benches. Just call around to your area junk/salvage people.

Mar 29, 2009 | 2005 Dodge Caravan

Not finding what you are looking for?
1998 Toyota Sienna Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...