Question about Cars & Trucks

Open Question

Remove xterra rear tailgate panel - Cars & Trucks

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 77 Answers

SOURCE: Remove lower rear trim beneath tailgate

Easy. First you need to remove the rear splash guards(the plastic pieces located near the tires)
After that, it should be about 6 bolts/clips and they are located in plain view just standing facing the bumper. Then the bumper pulls right out.

Good luck

Posted on May 02, 2009

  • 333 Answers

SOURCE: I need to remove 2004 toyota sequoia tailgate door

Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Posted on Sep 20, 2009

Testimonial: "Very helpful. thanks"

  • 41482 Answers

SOURCE: how do i remove the tailgate panel

screws and clips

Posted on Jun 02, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear tailgate inner panel so i can replace the wiper motor and sort out an annoying rattle??


Most door panels have push lock retainers you just have to pull the panel off by prying around the edge. they make a special tool for this but you can use a flat screwdriver just pry close to the plastic pins under the panel

Feb 06, 2016 | Cars & Trucks

3 Answers

2001 volvo v70 tailgate lock/unlock relay location. Tailgate not locking checked fuses, no sound from tailgate, however do get click sound from fuse area.


Check the wiring to the rear hatch. The cables break and cause a variety fo problems like yours. You will have to take the plastic cover off and expose the cables.

Mar 01, 2015 | 2001 Volvo V70

2 Answers

Rear hatch on my 2001 explorer will not open, rear window will but tailgate hatch will not. how do i open it with out the unlock button, no manual release that i can see...


I had a clip break when I tried to open my tailgate. I had to remove my inside hatch panel and find my way to the handle assembly. A little plastic clip (shaped like a T) had finally worn out, which wouldn't hold the locking arms, and I had to go to a Ford dealership for a $3 part; tailgate has worked fine since then!

Sep 01, 2011 | 2001 Ford Explorer Sport

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

Where is the fuse for the rear hatch on a 1993 chevrolet blazer? My rear hatch will not open at all. I can hear it ttrying to unlatch the rear windoiw but nothing happens.


If you can hear it then you don't have a fuze problem. More than likely it can be fixed by adjusting the catch in the tailgate. Open you hatch with the key and lower the tailgate. Remove the tailgate interior panel/cover and you'll see the catch for the window. Adjust the catch a little, tighten it up, raise the tailgate and close the hatch. Try your release on the dash again and see if this fixes the problem. You may have to repeat this a couple of times until you get it adjusted to where it needs to be. If this works, then reinstall the tailgate interior panel and you're all done.

Feb 17, 2011 | 1993 Chevrolet S-10 Blazer

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2003 JEEP LIBERTY?


REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the rear wiper arm from the rear wiper motor output shaft.
  3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
  4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
  5. Remove the bezel and gasket from the rear wiper motor output shaft.
  6. Remove the trim panel from the tailgate inner panel.
  7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
  8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
  9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
  10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
  11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.
To Install just reverse steps

Jan 23, 2011 | 2003 Jeep Liberty

2 Answers

Rear hatch will notopen


Rear Hatch Release/Lock Failure: How To Open The Glass
google_protectAndRun("ads_core.google_render_ad", google_handleError, google_render_ad); lg.php?bannerid=137&campaignid=106&zoneid=16&loc=1&referer=http%3a%2f%2fwww.s10forum.com%2fforum%2fadmincp%2fopenx_config.php%3fdo%3dox_zones&cb=d809956913 After a while, the mechanism (actuator) that unlocks and releases the rear glass hatch in
your Blazer or Jimmy will eventually burn out. when it does, there is really no way to open
the glass and lower the tailgate. The dash push button won't work, the rear key lock will
not work, the inside tailgat handle will not work, and you can not remove the interior
tailgate panel to access the mechanism because the screws can only be reach when
the tailgate is down (awesome GM design feature). The only way to replace the burnt
out actuator is to open the tailgate which you can't because the actuator is burnt out.

I've read stories that even the dealers don't know what to do, some have even cut up the
back panel to reach the so-called manuel release. Others said they pulled back the glued
on carpet to search for it also.

Well if you don't want to hack up the tailgate panel or rip out your carpet,
here's the easy way to open the glass:

You just pull back the interior tailgate panel right above the bump in the middle
where the latch is. There are no screws or bolts in that area, you can safely pull it back
about 2 inches. Then you'll have to stuck your finger in and push down the release bar.
See the 2 pictures below:
http://img.photobucket.com/albums/v2...z/IM000658.jpg
http://img.photobucket.com/albums/v2...z/IM000664.jpg
(No pictures allowed in this forum rolleyes.gif , oh well, click the links then)
The first pic is of the latch, it's the gold section.
The second pic shows what you need to push downward.
When you get your finger back there, you should be able to feel for the part that need to
be pushed down. When that part is pushed down, the glass has been unlocked.


Now that the glass is unlocked, it and the tailgate can be opened. Now you can remove the
interior tailgate panel, it has one screw on each side and easily lifts off.

The actuator that needs to be replaced costs $58 from the dealer, so if you don't want
to replace it yet, but still want to open the back, you can leave the panel off and just puch the
manuel release level. Here's the pic of the tailgate:
http://img.photobucket.com/albums/v2...z/IM000669.jpg
It's in the open section right below the latch, hows my fingure pushing it:
http://img.photobucket.com/albums/v2...z/IM000668.jpg

I haven't replaced my actuator yet, still trying to find it for cheaper than the dealer wants,
but hardly any part store guys know what the hell an actuator is

Nov 17, 2009 | 2001 GMC Jimmy

1 Answer

I need to remove 2004 toyota sequoia tailgate door panel to get access the rear tail light to install a backup camera. I don't see any obvious removal points.


Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Sep 20, 2009 | 2003 Toyota Sequoia

1 Answer

The key switch on my 1990 Suburban tailgate window won't work


Remove the back panel on the rear tailgate, should be some screws then pop off. From there you will be able to see the switch and see if you can operate it manually by using a screw driver and hitting the switch if not then replace it. Located next to the key lock

Feb 11, 2009 | Chevrolet Suburban 2500 Cars & Trucks

2 Answers

Taillight out on 2001 xterra


Pop your rear tailgate. Look inside for an access panel(s). In SUV's they're usually right behind the light assemblies on the inside. They'll either have screws or pop-outs. You may even have to remove part of the interior panel.

Once the panel is removed, access the light panel from behind and remove bulbs.

Feb 10, 2009 | 2004 Nissan XTerra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...