Question about 1996 Nissan Pickup

1 Answer

A rattle inside the steering wheel.

It started when I one day decided to realign the steering wheel with the front wheels.I took the steering column loose from the steering gearbox,rotated it,and put it back.Now there is a rattle inside the wheel OR the airbag.Can I take the bag loose,and fix the problem,without the bag deploying ?The left turn signal never has wanted to self cancel,unless it's sharp left turn.This was of course before I messed with the steering column.Dave.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

I would imagine the spring clip for the horn may be loose, or floating around in there, since you shouldnt have even touched the turn signal or any components there, i would definatlysay thats the problem, as far as the air bag, make sure to disconnect the battery and it should be ok, but work with it at your own risk

Posted on May 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a rattle in what sounds like the steering wheel inside the dash any ideas of what this could be


Sorry to say but your rattle is very common on these vehicles. Only solution is to replace the steering column. Good luck.

Jan 15, 2015 | 2008 Ford Escape

1 Answer

On a 2008 mercury mariner after you replace the torque sensor in the steering column do you have to realign the steering wheel to the rack an pinion i just had the torque sensor replaced and now my st


First check the air pressure in both front tires; if they don't match, that can cause the problem. If they do match take it back to the dealer that fixed it and take them for a drive with them driving it. Once they see the problem, tell them to fix it.

Dec 01, 2014 | 2008 Mercury Mariner

1 Answer

How do I remove the panel beneath the steering wheel?


There is a panel directly under the steering column will just pull down... you have to do that to take off the panels covering the steering column. The bottom panel of these two is held in place by screws.

Oct 31, 2014 | 2005 Chrysler PT Cruiser

1 Answer

I have a 2003 Mercury Grand Marquis with alignment problems causing tire wear. I had it realigned in the fall last year 2011 and months ago it's been steering to the left again... Just had it real


In the UK we would say 'have the car tracked' .. the wheel alignment checked and adjusted, which is a relatively straightforward and easy job.

However, be aware that there are other causes of tyre wear which isn't rectified by having the wheels aligned.

A bent or damaged steering arm can cause tyre wear. I once owned an old Mercedes that quickly wore one front tyre. Despite having the wheels tracked - aligned - three times, the tyre still wore. It wasn't until I looked under the car myself and found a damaged steering arm ...

A worn ball joint or worn/soft rubber bush can cause tyre wear. Having the wheels aligned cures nothing without first identifying the fault. I own a 1998 Jeep Grand Cherokee which, I am aware, has worn rubber bushes in the front steering/suspension set up. The front tyres wear badly, caused by the worn bushes. The tyres need replacing soon anyway, but I'll wait to get the tracking-alignment- done until after I've replaced the rubber bushes/tyres.

You've had wheel alignment done a couple of times and the problem of worn tyres is still there. It's not the wheel alignment at fault .. there's some other reason such as worn ball joint/rubber bushes or maybe impact damage to a steering arm.

The best option is to get a workshop to put the car up on a hoist for inspection. Tell them that wheel alignment ISN'T the cause of your uneven tyre wear. Any half-decent workshop should be able to find the cause within a few minutes.

A car which has suffered severe side impact - and has been repaired - can have a twisted/misaligned body. This too can cause uneven tyre wear

Mar 07, 2017 | 2003 Mercury Grand Marquis

1 Answer

I have a noise coming from the left side front wheel are. It is a rattle - took it to a local Toyota dealership who said it was the steering RAC well that was a $1000 mistake because the noise did not...


1) Take car to non dealer shops willing to give FREE opinion

2) Not likely you have a shock in Driver Front wheel, more likely a strut. Not likely strut needs to be replaced, but strut has a STRUT MOUNT (3 bolts of which can be seen when opening your hood) below this it is connected to STRUT BEARING which below it connects to UPPER SEAT OF STRUT or SPRING INSULATOR, that if loose will rattle. Usually, shops will not tighten, because to tighten is same labor as replace the parts. (Since you already dropped $1000 on ToyotaDealer, ask them to tighten FOR FREE since rattle is still there.)

3) There is a part called a "link," connects strut to stablizer bar, that if bushings are bad will rattle.
4) If stabilizer bar bushing(s) bad, will rattle early on but eventually clunking
5) Bad ball joint or tie rod can rattle as well

Never permit any shop to do expensive work on your car w/o first getting a second opinion somewhere else first. Do not tell second shop that you are there for a second opinion.

Shaking steering wheel at highway speed, no braking
1) Bad tire in front, bad tires in front, verify inflation of tires
2) Wheel alignment may be out
3) Front suspension parts (mentioned several above)

Highway speed to suddenly braking shakes steering wheel
1) Front brake rotors need to be inspected for warping
2) Test calipers on empty road at 40 mph, going straight on very LEVEL ROAD, hit brake pedal SOMEWHAT hard while barely touching steering wheel. If car jerks to one side, instead of braking straight on, you may have a caliper, ABS, or brake fluid pressure regulator off.
3) If brake rotors are warped, may as well replace front brake pads at same moment. Use ceramic.
4) When you drive on VERY LEVEL road on highway, steering wheel must be centered, let go lightly of steering wheel. Did car stay in middle of lane? No? Get a 4-wheel alignment.

Sep 13, 2010 | 2007 Toyota Camry

1 Answer

Play in the steering wheel column after position adjustment


When they did the alignment it's possible that they used a tool that locks the steering wheel straight while it's on the alignment rack.If they put too much pressure on the wheel when they used the steering wheel seat lock tool it may have stressed you tilt lock mech causing it not to lock where you want it.Hope this helps

May 16, 2009 | 2005 Hyundai Sonata

4 Answers

Strus or shocks in the front end of the magnum?


According to the replacement parts guide, they are struts and I checked for all wheel drive and 2 wheel drive and all are showing struts.

Apr 04, 2009 | 2005 Dodge Magnum

1 Answer

Front end rattle


It's a loose steering column. Remove the black plastic shield under the steering wheel. Lossen the bolt that holds the two shafts together, slide them together as far as they'll go, and re-tighten the bolt. It's that simple... to stop that annoying rattle.

Mar 06, 2009 | 2005 Chevrolet Equinox

1 Answer

Loose steering wheel, 1989 Jeep Grand Wagoneer (FSJ)


it sounds like all you need to do is as follows, remove the steering wheel and behind it inside the column you will find a couple of screws or bolts that hold the tilt steering assembly together, they have most likely come loose and just need to be retightened , I would recomend that when you have the bolts out that before you reinstall them you put on some kind of thread locker (ie) lock tite. this should solve the problem

Feb 09, 2009 | 1988 Jeep Grand Wagoneer

2 Answers

Steering Columin Housing


it could be the wiring rattled loose or a nut or a screw has come loose inside the steering column, you might be able to get at it by loosening the plastic at the bottom of the dash below the steering column. or the worst thing could be something has broke loose..

Nov 07, 2008 | 2007 Chevrolet Impala LS Sedan New Cars

Not finding what you are looking for?
1996 Nissan Pickup Logo

414 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...