Question about Ford F-150
Smog check in CA failed due warning lamp failure
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
po301 thru po306 all misfire codes cylinder 1-6 remove plugs and replace them..... set the plug gap first
i suggest u replace the wires also if they never been replaced all these misfire codes can set the others and one is for the oxygen sensor ( 02s or HO2S) CIRCUT MALFUNCTION do u know how to check wireing systems
do the tune up plugs (set gap) .052-.056 change the fuel filter also. clear the codes hows it run
this info is for 98 E-250 4.2Litre
what engine do u have 4.2L or 4.6L i know it is a v-6 by the codes
Posted on Dec 15, 2008
I have a 1996 ford f150 4.9 liter.The truck runs great but bad gas mileage.the only problem is i am getting codes p0401and p0402 what should i do.
Posted on Dec 18, 2009
Some 2001-2003 F-150, 2004 F-150 Heritage and 2001-2003 E-150/250 vehicles equipped with a 4.2L engine may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble codes (DTCs) P1131 and/or P1151 (system too lean bank 1 or 2). This condition may be due to leaking isolator bolts/port gaskets in the upper-to-lower intake manifold mounting area. This condition is sometimes intermittent and may not be apparent on a warmed-up engine.
Perform a self test. If DTC P1131 and/or P1151 are the only codes stored in the powertrain control module (PCM) proceed to Step 2. If any additional DTCs are present, follow normal diagnostic procedures found in the PC/ED Manual.
Remove the upper intake and replace only the port gaskets (9H486) and isolator bolt assemblies (9S479). The new isolator bolt assemblies use a rubber material that is green in color, do not install the old isolator bolt assemblies with the black rubber material. Do not replace any other intake parts or gaskets.
While the upper intake manifold is removed, check the exhaust gas recirculation (EGR) orifices that are pressed into each primary port of the lower intake manifold. If any of the orifices are plugged with soot, clean and unplug them with a pick and solvent.
PART NUMBER PART NAME
1L3Z-9H486-AA Port Gasket
3F2Z-9S479-AA Isolator Bolt
Posted on Jan 13, 2010
SOURCE: f150 2002 4.2 eng codes:
1400 is dpfe, 1151 is an 02 sensor code, 1131 is also 02s11 code, P0316 = Engine Misfire Detected on Startup (First 1000 Revolutions)
Po301 Cylender 1 misfire, p0174 lean condition bank 2, And p0171 is lean bank 1. Either this is in need of a whosale of repairs or you have computer issues, From looking at the codes i would first do a complete tune up, Including wires, And inspect for a vacume leak before replacing any 02 sensors..
Posted on Jun 14, 2010
Tips for a great answer:
Jul 08, 2014 | 1999 Chevrolet Silverado 1500
Apr 07, 2013 | 1995 Toyota Tercel
Nov 15, 2012 | Cars & Trucks
Nov 15, 2012 | 1997 Lincoln Town Car
Jun 27, 2012 | 2001 Ford Windstar
Apr 06, 2011 | 2003 Lincoln Navigator
Jan 13, 2010 | 2003 Ford F150 Regular Cab
Nov 29, 2009 | 2003 Ford Taurus
Jul 07, 2009 | 1999 Mercury Cougar
May 17, 2009 | 2003 Lincoln Navigator
17 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: