Question about Cars & Trucks

1 Answer

1996 buick centry transmission removal

How to remove a transmission from a 1996 Buick century

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,159 Answers

Place the car on a hoist .--- remove the tail shaft.-- support the rear of the engine .--- remove the inspection plate under bell housing--remove battery positive lead-- place a jack or other mobile support under the transmission-- undo the rear engine mount cross member.--- disconnect all wires and connections--If manual remove the gear lever and turret from inside the car or disconnect linkages to the box------ if auto remove the bolts holding the converter to the flex plate and push the converter back towards the gear box. use a piece of thin wire to hole it there by tying a bolt hole back to the bell housing inspection bolt hole. IF manual and auto ---remove the bell housing bolts and pull gear box straight back . watch for transmission oil coming out of the rear of the transmission. Installation is reverse process.

Posted on Jan 01, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: instrument cluster removal 2001 buick century

You have to remove the dash but it is VERY simple to do.

Remove the fuseblock cover on the end of the dash on the passenger's side.
Once removed, remove the screw holding on the end of the dash.
Now, next to the glove box, to the right, remove the one screw on the bottom. Then remove this panel by pulling it out (it will now be held on by two clips at the top.)
Now, looking at the temperature control cover, remove the two screws from the bottom of this. Pull it off. It also is held on by two clips.
Now, below the steering wheel, remove the one screw from this panel (on the right). On the left there is a "plug" holding it in place, Pop out this plug. I think there are a couple of clips now holding this on at the top.
Now that you have all of that pulled out, pop the dash out. At worse, it is held in with clips.
Now that you have this out, there are four screws holding in the instrument panel. Take out these four screws. You will find one electrical cable connected to the cluster. Pop that off of the cluster and you now have the entire instrument cluster in your hands.

I've had to take mine out to figure out why my gear indicator/odomiter would not illuminate (Buick told me it was a light). I can see where this encased LED has a short (black mark). It is soldered onto the board. Looks like I have to purchase a repaired board.

I hope this helps.

Posted on Nov 03, 2008

alicantecoli
  • 22156 Answers

SOURCE: trying to remove radio from 1998 buick century

wow lot of work ,,normally just two holes either side or radio and push in a special tool and they pop out

Posted on Nov 20, 2008

  • 116 Answers

SOURCE: 96 Buick Century won't pass imisions code P1441

code is evap system flow during non-purge
check the hoses for holes or broken disconnected hoses also check the fuel cap emissions diagram under the hood will give u the location of the evep purge solenoid if all checks ok then replace the soienoid and clear the codes
rank & vote my solution

Posted on Dec 13, 2008

michigan man
  • 3533 Answers

SOURCE: 95 Buick Century dash removal?

you should not have to remove the dash to install a new radio all you have to do is remove the trim around the radio and then take out the bolts that hold the radio in and remove the wires from the back and also if there is a Walmart or Radio Shack near you get an installation kit and you plug it from the plugs from your old radio and it is alot easier to wire it that way

Posted on Mar 04, 2009

emissionwiz
  • 75822 Answers

SOURCE: Need to replace tail light bulb on 1996 Buick Century

Inside the trunk, under the carpet behind the tail lights will be a whole bunch of small plastic nuts, running from one side of the car to the other. Take all of these plastic nuts off, and the whole tail light assembly will come off in one large piece. Find the bulb you need to replace, and reassemble

Posted on Apr 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How long should it take to replace a thermostat on a buick centry 2002 3.6L


the 2002 buick century does not have a 3.6L V6 it has a 3.1L V6 in order to replace the thermostat you have to remove the exaust crossover pipe the book time is 2.4 hours so it is a pretty good job...good luck

Jul 16, 2011 | 2002 Buick Century

1 Answer

I have a 93 buick centry it will go into 1st 2nd and reverse but will not go into 3rd I had some problems with it shifting into 3rd but just went out


Unless you are knowledgeable in diagnosing internal transmission problems, it is impossible to help you over the internet. Take the vehicle to a knowledgeable transmission shop and be prepared to spend a good amount of money.

Mar 28, 2011 | 1993 Buick Century

1 Answer

1995 buick century custom, the anti lock light came on and the brakes seem fine. What should I look for


i have a 1995 buick centry and my anti lock light came on should i be concerned about anything? my bracks work fine.

Sep 09, 2010 | 1995 Buick Century

2 Answers

How do I remove my cv axel and install a new one


just remove the tire and hub. then it should slide out

Mar 26, 2010 | 2002 Buick Century

1 Answer

Replacing a belt tensioner on a 1996 Buick Century


remove belt,remove bolt in tensioner not pulley.note the bolt in the pulley is left handed threads

Jan 31, 2010 | 1996 Buick Century

1 Answer

Removing wiper blade arm 1996 buick century


Remov nut under the cover at cowling end of arm.

Jul 31, 2009 | 1996 Buick Century

1 Answer

Thermostat location


left side of engine as you face it from up front, under the exhaust pipe that runs over the top of the transmission, it is very hard to get to the top bolt, have this same car.

Feb 23, 2009 | 1999 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...