Question about 2006 Ford Fusion
The bulb burned out on my 2006 ford fusion. I replaced the bulb and it still does not work. What can I do?
Check for volts in the socket. If no volts check again but place black probe from multimeter on the negative battery post. If you get 12 volt now the ground for the socket is bad, probably corrosion.
Posted on Dec 31, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: turn signal problems
Turn signals have a relay (its a small switch that charges and discharges current) which controls your turn signals blinking speed and interval. This is most likely your problem. You should be able to get a new one at your local parts store. Follow these instructions, in this order, and let me know how it works.
Step 1:Turn on the hazard lights and walk around the Taurus checking that all four turn signal lights are working. If any of them are not working, replace the bulbs. A non-working bulb in any of the turn signals will often make the turn signals appear that a flasher is going bad.
Locate the fuse box and check the fuses for the turn signals. There may be more than one. Replace any fuses that are blown and then recheck the turn signals again. If they still aren't working properly, then move on to replace the flasher. Step 3: Look for a round, silver-colored object near the fuse box. Put your finger on the object and turn on the turn signal. You should be able to feel a mechanical clicking as the turn signal blinks. This is the flasher. Step 4: Pull the silver flasher out of the socket and replace it with the new one. Each of the flashers should have two pins sticking out of the bottom side. Start the Taurus and recheck the turn signals to ensure that they work. Joel
Posted on Mar 04, 2009
I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems
Posted on Aug 06, 2009
This is straight from the owner's manual.
#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.
Install new bulb(s) in reverse order.
Posted on Jan 23, 2010
I just changed my rear turn signal. Really easy. There is two 1/4 inch bolts visible when you open the tailgate. Take both of those out and gently lift the light housing out towards the outside of the vehicle. There is two small clamps on the other side of the fixture that just slide right out when you pull on it. There you go
Posted on Feb 21, 2010
This link is from the handle to the latch. The door panel has to be removed in order for this problem to be fixed. The linkage is inside the door panel, it is a small diamater metal rod called a link. If you do the job yourself be careful not to break the door panel. In a shop, the labor is 1 hour for the job & if any, parts will be a seperate charge.
Posted on May 08, 2010
Tips for a great answer:
Dec 01, 2013 | 2006 Ford Fusion 1.4
Jan 31, 2013 | Ford Cars & Trucks
Oct 13, 2012 | Cars & Trucks
Jul 21, 2012 | 2006 Ford Fusion
Jul 05, 2011 | 2006 Ford Fusion
Aug 10, 2010 | Ford Fusion Cars & Trucks
May 20, 2010 | 2006 Ford Fusion
Mar 17, 2010 | 2006 Ford Fusion
Oct 05, 2009 | 2006 Ford F-250 Super Duty
102 people viewed this question
Usually answered in minutes!