Question about 1995 Chevrolet Camaro

1 Answer

95 camaro 3.4 l replaced head gasket & timing chain now hard to start but does start when i give gas pops through throttle also here lifter tapping

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 40,734 Answers

Recheck the valve timing as it appears that you may be a tooth out on the chain and you have an inlet valve not quite closed . The tapping may be the piston just touching the valve head from the wrong timing

Posted on Dec 31, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 341 Answers

SOURCE: 1989 chevy 350 automatic, white smoke

white smoke is antifreeze try checking the compression

Posted on Nov 08, 2008

fyrebyrd1
  • 121 Answers

SOURCE: Valve train tapping?

The 6.0 engine had an issue with piston to bore clearances, from the factory these clearances were excessive. It is reffered to as "piston slap". This condition is known by GM, but most dealers say it's normal. It can be as slight as an annoying tick, to a clearly audible clacking noise. Unfortunately the condition was under played by GM, and there are many folks who haven't been able to get help with their trucks. I own an '03 Silverado w/6.0, and hear this noise everytime I start my truck. I deal with it, because I'm a mechanic and figure I'll be able to fix it if I need to. Research more online about this condition. I've found many websites that relate to this issue (Google: 6.0 piston slap) I hope this helps.

Posted on Nov 19, 2008

  • 740 Answers

SOURCE: 95 camaro no spark on cylinder 6

Loud popping in the intake means that the unburnt gas exploding in intake.... Check cranks sensor and gear. Gear may dirty or even damage or BAD crank sensor the sensor provides reference for spark signal. So this may be your problem. Contact if you need more help. Thanks for using FIX YA

Posted on Jan 24, 2009

outdoorsman5
  • 631 Answers

SOURCE: 95 Chevy lumina 3.1 engine head gaskets just

Could be throttle position sensor. Does it run rough at 20 mph or smooth?

Posted on Aug 19, 2009

richard3707
  • 70 Answers

SOURCE: rough idle timing chain? 2004 chevy cavalier

Sounds like a 2.4 Quad four engine? If so the chain has either different colored links marked links that have to be aligned with the marks on the cam gear[s] and the crank gear.A chiltons book will show you how.

Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I remove gear-to-gear timing cam?


images for How to remove a gear to gear timing cam ...

DIY Timing Chain and Gears Removal - YouTube

? 6:31
https://www.youtube.com/watch?v=eMXO1bvUCMs
Dec 30, 2012 - Uploaded by Bullshitkorner
The most important part when doing timing gears on a engine is ... Doing this inside the engine bay will be a bit of a pain in the axx but it is doable for sure. ... How to build a Chevy 383 Part 3: How To Install a Cam & Timing ...

Head removal & replacement, Timing Chain & gears also ...

? 3:28
https://www.youtube.com/watch?v=CnXtwR1N0Og
Apr 28, 2012 - Uploaded by No1hmfic Gibson
Head removal & replacement, Timing Chain & gears also, 97 Chevy S10 2.2 ... replacing the head gasket in a chevy cavilier 2.2 liter 4 cylinder - Duration: 9:38. ... 98 S10 Vortec V6 4.3 Intake Gasket Replacement Part 1 of 5 ...

Chevy S 10 2.2 L Engine Timing Chain Replacement Guide ...

? 7:30
https://www.youtube.com/watch?v=8nX5HARPSF4


Feb 03, 2016 | 1998 Chevrolet S-10 Pickup

2 Answers

No Start - Lanos 99 SOHC 1.395cc


Hi. I can give you a simple, but time consuming test to do to check your intermittent compression problem. New hydraulic lifters cause a lot of problems until its settled. Remove the camshafts and the hydraulic lifters. Take each hydraulic lifter and put it in a vice(becarefull not to damage them) and squeeze out all the oil in the lifters. Then put them back and replace camshaft and allign timing marks. Check compression ratio. What happens sometimes is that the oil pressure is too high(stuck oil pressure release valve or cold thick oil) and this causes the oil pressure to put so much pressure on the hydraulic lifters, that it slightly forces the valve open. That will cause your low compression as well as backfire through the intake.

Jan 14, 2014 | 1999 Daewoo Lanos

2 Answers

Replaced head gasket now it will not start?


was it the correct gasket? if its even off by a little it could def cause no start. if so the you need to check map sensor and also throttle posistion sensor

Oct 24, 2012 | Cars & Trucks

1 Answer

No compression in 3 and 5 in my 2000 dodge ram 1500 5.9 and what all should i change if i need to replace head or head gasket should i do any thing with cam lifters and push rod and timing chain


Hi panther You should have the cylinder heads serviced. They will crack & pressure test them as well as surface grind the meeting face. They will also detect any valve seating or guide & seal wear. As for the timing chain it depends on km. ok the engine has done. Check the guides & tensioner for wear. If in doubt have the machine shop check email out.

Jul 24, 2011 | 2000 Dodge Ram 1500 Truck

1 Answer

My 95 camaro 3.4 v6 overheats what causes this problem & how to solve it?


3.4 liter, you may have a bad water pump or at worst you have a bad intake manifold gasket which is a common failure to the 3.4 liter V6 engines. Start with the simple, flush out the cooling system and replace the thermostat. Inspect any signs of possible intake gasket failure and head gasket failure and replace. After that has been inspected, move on to a possible weak water pump and will need to be replaced. Good luck and hope this helps.

Mar 04, 2010 | 1995 Chevrolet Camaro

1 Answer

95 Jeep Cherokee bckfiring through exhaust and popcorn under hood


Your a thinker and off to a good start. How about going to TDC on crank,pull dist cap and look where you rotor is. Thinking timing chain here. Put a timing light on it just to get some practice and see where the timing is. Also rock the crank back and forth with a long ratchet or tool of choice while watching the rotor. May need help,your looking for timing chain play,think it jumped about 3 to 4 teeth. Let me know because this advice is sort of a helpful quess

Sep 29, 2009 | 1995 Jeep Cherokee

1 Answer

95 camaro no spark on cylinder 6


Loud popping in the intake means that the unburnt gas exploding in intake.... Check cranks sensor and gear. Gear may dirty or even damage or BAD crank sensor the sensor provides reference for spark signal. So this may be your problem. Contact if you need more help. Thanks for using FIX YA

Jan 23, 2009 | 1995 Chevrolet Camaro

Not finding what you are looking for?
1995 Chevrolet Camaro Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...