Question about Cars & Trucks

1 Answer

Nissan sentra problems

I have a sentra 160i i replace fw bearing/hubs and cv joints after a few months my mech. informed me that i need to replace brgs and hubs again how can this be

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,103 Answers

Calipers are sticking and making the brakes heat up and ruining seals and such..

Posted on Dec 31, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
kaokensho
  • 2 Answers

SOURCE: how to replace front wheel

I can tell you on a 93 Altima that you have remove the entire wheel knuckle and press it out from the rear. Yeah, the knuckle, remove the strut tower bolts, drive train ( which can be lighty pressed out ), caliper and bracket, and remove the ball joint. There's a snap ring at the back of the wheel knuckle that holds the bearing, then press it out with a socket and a table vice or something to that effect. By the way the going commercial rate if you take it to a shop and have them do it starts at $150 for labor. Worth it, oh yeah.

Posted on Aug 15, 2008

  • 95 Answers

SOURCE: nissan sentra gxe 03 rear wheel hub bearing problem

Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Posted on Oct 15, 2008

alicantecoli
  • 22246 Answers

SOURCE: 1998 nissan sentra, replacing cv joint boot covers

firstly remove the wheel trim and undoo the big nut on the end of the drive shaft,Then jack up and remove wheel and put stand under body remove the lower track control arm pinch bolt from lower suspension .remove brake caliper separate the lower arm from the bottom of the strut then push the drive shaft through the hub assembly and its clear .cut off old boot and look for the circlip that hold the end on which should be in the centre if the unit in a recess to allow access to the ends of the clip .You shouldnt need to remove the whole shaft just spread the clip and tap with a copper hammer.wash the thing out with diesel and take the balls out and give it a good clean ,rebuild and pack with grease slide the new rubber down the drive shaft ,refit the end but dot hit the threasded bit with a hammer put a block of wood their first then tap it on.Refit the suspension and away you go

Posted on Mar 14, 2009

yotaguy
  • 232 Answers

SOURCE: replacing CV Joints

Yes you can remove the drive shaft by unbolting the bottom ball joint,then removing the nut that holds the shaft in the hub I would'nt recommend trying to replace just the CV joint as this can be a very complicated procedure involving specialized tools and more than just general mechanical skill,this isn't true of all,as some CV's come apart fairly easily.If the joint is bad you should probably just replace the axle.Remember to match mark any adjustable parts you may have to disassemble,and when you reassemble make sure to check the splines of the shaft and the drive hub,remove any foreign material and carefully file or sand any burs or scratches,any of these can cause the spline to bind on reassembly and possibly cause irreparable damage to one or both parts.Good luck hope this helps.

Posted on Apr 10, 2009

  • 14036 Answers

SOURCE: severe bearing noise from front wheel bearing/cv

you have to replace bearing and hub as a unit.you have to remove remove brakes and caliper rotor set them aside dont disconnect brake line. get a piece of clothes rack wire to hold brake caliper .do not let it hang by brake hose. you got to remove hub nut. best way to do that is loosen it a litttle while tire still on weight of car keep wheel from turning .

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change rear bearing on a 2001 Nissan Sentra


Most newer cars have a bearing that is pressed in to the hub. In order to do the repair you should have to replace the entire hub. This is actually easier and cleaner because the bearings are lubed, sealed and pressed in the hub. They usually cost around $30 and should be available through your local parts store. In most cases the hub is held on by a large nut so I recommend that you make sure you have a socket that is large enough.

May 13, 2010 | 2001 Nissan Sentra

2 Answers

Alot of road noise from front of car, suspect cv or drive train issue , As speed increases noise gets louder. Engine runs smooth, new tires 6mos. ago, alignment good.


MOST LIKELY CAUSE OF THIS IS THE WHEEL BEARING, DEFECTIVE CV JOINTS ONLY MAKE NOISE IN TURNS AND THAT IS A CLICKING NOISE,.

Mar 16, 2010 | 2004 Nissan Sentra

1 Answer

Step by step on how to replace front wheel bearing on 02 Nissan Sentra GXE


Raise vehicle, remove wheel, remove brake caliper, remove brake rotor remove steering knuckle by disconnecting the tie rod, ball joint, and strut. press out hub, remove snap rings press out bearing. Reassemble in reverse order.

Aug 01, 2009 | Nissan Sentra Cars & Trucks

1 Answer

Severe bearing noise from front wheel bearing/cv joint area.Cv joint still lubricated,I tend to think axle support bearing is dry & on the way out,but only assuming.How does front wheel bearing come out of...


you have to replace bearing and hub as a unit.you have to remove remove brakes and caliper rotor set them aside dont disconnect brake line. get a piece of clothes rack wire to hold brake caliper .do not let it hang by brake hose. you got to remove hub nut. best way to do that is loosen it a litttle while tire still on weight of car keep wheel from turning .

May 03, 2009 | 1999 Daewoo Lanos

1 Answer

Does hub need replacing when replacing a wheel bearing


rdfairfield: if you are asking about the rear? Yes, that is the only way the part comes and is manufactured. It is a hub and bearing assembly..

Apr 21, 2009 | 2002 Nissan Sentra

1 Answer

2006 Saturn Vue Wheel Bearing


it should come out once you have disconnected:Brakes,strut,ball joint.tire rod end,cv joint!if it is not put the cv joint nut back on until safe enough to give it a tap with hammer to knock back & out shaft this should come as one piece HUB the bearing is pressed in! better to change whole HUB good luck this hopefully helped you out!

Jan 31, 2009 | 2006 Saturn Vue

1 Answer

Mazda rustler 160i wheel bearings


a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Dec 03, 2008 | 1997 Mazda 626

1 Answer

Front spindles


ok... replace them....inspect the bearings and replace if necessary....
Robert
and have the cv joints inspected as well.

Sep 05, 2008 | 1991 Nissan Sentra 2 Door

2 Answers

Nissan sentra gxe 03 rear wheel hub bearing problem


Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Jun 12, 2008 | 2003 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...