Question about Toyota Tundra

1 Answer

My switch want turn all the way so i can start my truck

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers

What switch? tell where hand is.

Posted on Jan 02, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Truck wont start


It could be the fender mounted starter relay under the hood. Or if you took off the small wire at that relay (its from the ignition switch), it should have voltage when the key is held in start. If it does have power in start, probably the relay. If no power in start, either the switch or the neutral safety switch is acting up.

Jan 24, 2014 | 1985 Ford F150

1 Answer

Resetting the passlock


1. First, insert the ignition key and turn the ignition switch to the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switch off for 30 seconds.
3. Turn the ignition switch to the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switch off for another 30 seconds.
5. Turn the ignition switch to the "On" position for 11 minutes a third time.
6. Turn the ignition switch off for 30 seconds one final time.
7. Turn the ignition switch to the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, Go to this link for info
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Sep 08, 2012 | 2000 GMC Yukon Denali

1 Answer

When i turn the ignition key over the 1994 gmc suburban will not start. then when i turn the ignition key over again the vehicle will start with no problem. i dont do anything between turning the key over....


Neutral Safety Switch ? located at the bottom of the steering column. Mine is tricky, have to pull the shift lever while turning over to get it started. happened after i replaced ignition switch & Neutral Safety Switch

Aug 20, 2011 | 1994 GMC Suburban

1 Answer

When i turn the key to start the truck upit turns to run but wont go to start, it turns all the way but doesnt start


Not much to go on---but I'll try here.

Ok first thing check to see if truck is in park---sometimes it may be in park but the park switch will not start truck unless the switch is depressed.

try putting truck in neutral with foot on pedal to start truck-----if starts the problem is with the switch.

If not, then you have a ignition switch problem---there is an ignition switch box under the dash on topside of steering column with has adjustment screws mounted to column.

loosen screws and slide ignition box toward the steering wheel to achieve the start position of the ignition switch box to start truck.

Jan 23, 2010 | 1988 Ford F 250

1 Answer

I turn key switch to start but car does not turn over switch semms bad when i turn the switch it does not go to start?


be more specific you turn key and engine dosnt turn over ? are your headlights working

Aug 24, 2009 | 2005 Chrysler Pacifica

2 Answers

Has truble starting and staying started


Sounds like a bad ignition switch. Not the lock cylinder, but the electrical switch.

Jun 30, 2009 | 1983 Buick LeSabre

3 Answers

Engine turns over but will not start


Hi there yep the switches are basically in the same location.Try the next time this happens to bump on the steering wheel while cranking or pushing in on the steering wheel towards the windshield if it starts right up you'll know for sure that its the switch or its out of ajustment.

Dec 20, 2008 | 1997 Chevrolet S-10 Pickup

2 Answers

Nissan Frontier 1998


I had the same problem. Turned out to be the clutch interlock switch mounted under the clutch pedal. A combination of the clutch pedal and switch mount being there for 15 years and had bent just a little not allowing the switch to be fully depressed and my floormats getting behind the clutch pedal not allowing the pedal to push the switch all the way. You can press the switch by hand and turn the key (making sure the truckicon1.png is in neutral of course). If it starts reliably every time you found the problem. I adjusted the switch out by disconnecting the wire to the switch and loosening the 14mm nut behind the switch and turning the switch out a couple of turns. When moved out a bit and keeping the floormat from behind the clutch pedal, voila, starts every time. This fix came after a new battery, new starter, new battery cables and still the intermittent no crank was present. Start with the cheap/free stuff first and move on from there if needed :-)

Jul 25, 2008 | 1998 Nissan Frontier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...