Question about 1997 Mitsubishi Pajero

Open Question

Change spark plug leads 3.5 dohc

How to change spark plug leads on 3.5 pajero with 24 valve. don't know how to remove/replace connection at rear of motor.

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: need engine specs for mitsubishi pajero 1996 3.5 lt 24 valve dohc

ed904ac.gif
Here ya go....get the rest of the info right now.

Posted on Mar 26, 2009

Technopro
  • 243 Answers

SOURCE: 1993 Pajero V6 3 litre has a leaking welsh plug

Engine has to come out and I advised to ger all frost plugs replaced at the same time.
Cheers

Posted on Apr 23, 2009

techprogrami
  • 57 Answers

SOURCE: i need to replace the spark plugs in a 2001 mitsubishi montero sport

http://www.monterosportonline.com/diy-perf2.html
this gives step by step as well as pictures

Please Rate Me

Posted on May 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changhing valve cover gasket 03 mitz galant 3.0 v6


  1. Disconnect the negative battery cable.
  2. Remove the upper intake manifold.
  3. On the 3.0L DOHC engine, remove the ignition wire cover.
  4. Remove the ignition wires and spark plugs.
  5. Remove the crankcase ventilation tubes from both valve covers.
  6. Remove the retaining nuts and engine wiring from both valve covers and move aside.
  7. Remove the valve cover retaining bolts and studs.
  8. Remove both valve covers from the engine.
To install:
  1. Clean the valve cover gasket sealing surfaces.
  2. Install new valve cover gaskets onto the valve covers.
  3. Place the valve covers into position.
  4. Reinstall the valve cover retaining bolts and studs and tighten in sequence to:

    3.0L SOHC engine: 7 ft. lbs. (9 Nm)3.0L DOHC engine: 42-54 inch lbs. (4-5 Nm)3.5L engine: 30 inch lbs. (3 Nm)
  5. Install the engine wiring and tighten the retaining nuts.
  6. Install the crankcase ventilation tubes into both valve covers.
  7. Install the ignition wire separators, the ignition wires, and the spark plugs.
  8. On the 3.0L DOHC engine, install the ignition wire cover.
  9. Install the upper intake manifold as described in this section.
  10. Connect the negative battery cable.
  11. Run the engine and check for leaks and proper operation.

Jun 25, 2017 | Cars & Trucks

1 Answer

Saab 900se sound like running on 3 pistons


Have you checked you're actually getting a spark on all 4? Take out each plug in turn, leave it connected and ensure the metal body of the plug is touching a metal part of the car (the cylinder head will do :) ) Get someone to crank the car for you & see if there's a good, fat spark on the end of the plug. If you find one doesn't have a spark, start by changing over the plug lead with one of the others & see if the fault moves with the lead. If so, replace the faulty lead; actually, I'd replace the set as if one has gone, the others won't be far behind.

There are many other faults that could cause that symptom but I don't know that engine well enough to be much help :(

Let us know how you get on.

Aug 26, 2016 | 1997 Saab 900

1 Answer

How to change the spark plugs in a 2002 kia sportage 2.0 liter dohc


Oh, how fun, changing the spark plugs on the DOHC Kia. Based on experience, I strongly suggest you get a Chilton/Haynes repair manual for your SUV. It will lead you through the process step by step. I'm a rather short F, so I didn't have much difficulty reaching the spark plugs (you have to remove the center cover first). The spark plugs are rather deep in the valley between the cams/valve covers. Because of this it's easy to cross thread them, so take care to avoid this costly mistake. I don't think I would attempt it on the Sportage unless I had some kind of scaffold to stand on.

Feb 28, 2015 | 2002 Kia Sportage

1 Answer

What lead goes to what spark plug on nj pajero dohc as only 3 leads


your engine should be 6G76 V6

number one cylinder is closest to the timing belt

With the plug out and finger over the plug hole while turning the motor clockwise ...number one cylinder will be the only cylinder coming to compression at Top dead Centre

on the dissy The firing order is 1-2-3-4-5-6,

with rotor to number one when it is at Top Dead Center

the heads wont be 123 on one bank and 456 on the other
more like 1 3 5 on one bank and 246 on the other

hope this helps




Oct 19, 2014 | 1997 Mitsubishi Pajero

1 Answer

Do i have to remove intake to replace rear spark plugs on a 1999 ford taurus


If it is an OHV engine, No. If the engine is a 24 VALVE DOHC motor then, yes.

Oct 13, 2010 | 1999 Ford Taurus

1 Answer

Changing the back plugs on 99 ford taurus dohc 24


You have to remove the upper intake manifold.

May 17, 2010 | 1999 Ford Taurus

1 Answer

Can you supply me with a digram of spark plug installation on vehicle?


Sorry for the delayed response. I am going back and answering unaswered questions. I do not know if you still need this information, however I am answering it in case you do.

For the 3.5L DOHC 24-Valve
Firing Order:
1-2-3-4-5-6
Cylinders:
(back)
5.........6
3.........4
1.........2
Coils are on the Plugs.

Again my apologies...

Let me know if this helped...

Mar 09, 2010 | 2001 Nissan Pathfinder

1 Answer

Ignition coil spark plugs what is the diagram of the firing order


For the 3.0L DOHC V-6 24-Valve
Firing Order:
1-4-2-5-3-6
Cylinders:
(Back of Vehicle)
1------2------3
4------5------6
(Front of Vehicle)

Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Feb 19, 2010 | 2003 Mazda MPV

1 Answer

I want to change the spark plugs in my 2001mazda tribute


See the tips section of my profile on Fixya. I have complete instructions on how to change the plugs and coils.

Jul 05, 2009 | 2001 Mazda Tribute

1 Answer

1993 nh pajero 3 LTR running on 5 CYL


Hi Roy,
You say you have compression? is it well within the range of the other cylinders? if it is i.e. around 100 psi then possible bent or sticking valve? although you have a spark when plug earthed out of head is there possibly some foreign matter isolating the plug or is it the plug itself breaking/tracking down when in situe?
Failing all these, try a small amount of fuel direct into the cylinder to see if it fires briefly (Not too much just a couple of mls)
Maybe possible Head gasket failure? (I doubt it as all other cyls fine)
Can't think of anything else I would try,
Hope this helps!
Paul 'W'
Onyer~EDson(:0)~[><U.K.

Jan 13, 2009 | 1994 Mitsubishi Montero

Not finding what you are looking for?
1997 Mitsubishi Pajero Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...