Question about Jeep Cherokee

1 Answer

I installed new spark plug wires & did not get some of them back in the right place, can u help me it is a inline 6 1999

Posted by on

  • rwchd1200c May 20, 2009

    Yes it was just what I needed. I thank you for the help & the (picture) lol have a good night

    RW

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 117 Answers

Hello there

That can easily happen when you undo all the wires at once. Here is the wiring diagram for the firing order which will help you correct the problem. Please note that 1 on the diagram is the front of the engine. Hope this helps and please don't forget to rate me.

Many Thanks

Firing Order I installed new spark plug - i6_order.jpg

Posted on May 20, 2009

  • ILikeBMW
    ILikeBMW May 20, 2009




    Sorry forgot to load the picture. Here it is.



    Thanks

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 jeep cherokee 4.0liter inline 6 diagram needed for the spark plug wires to be placed properly from the spark plugs to the didtributer cap please


Just follow the pattern as it is under the hood. If you have to, draw a diagram to help you along the way.

Apr 30, 2012 | 1998 Jeep Cherokee

1 Answer

Replace spark plugs in 1997 4 cyl. ford ranger


Hello, I will suggest you get these few tools before you with the replacement.
(1) Spark plug socket with rubber insert to hold plugs in place while inserting & removing.(2) 6inch extensions for your 3/8ths inch socket wrench,(1) Swivle Socket extension for your 3/8ths inch socket wrench.(1) 1/2inch socket for exhaust manifold screws. A little quantity of anti-sieze for the spark pluggs to be applied to the pluggs if they are proving difficult to get out.
Start with the 1st cylinder at the front of the engine on the passanger side.
STEP 1.
Twist & remove the spark plug boot from the existing plug.
STEP 2.
You have to use a very small flat edged screwdriver to open the clips that hold the plug wires together.
STEP 3.
Use a 6" extension & a 3" extension & your deep socket for the spark plug.
STEP 4.
Remove the first plug and replace the old plug with a new Bosch Platinum Plus 2 prong plug and use some anti-seize on the threads and tighten to the appropriate torque.
STEP 5.
Remove the old plug wire from the coil pack. It will be going to the 2nd coil pack (located to the rear of the first coil pack) and install the new plug wire in the coil pack.
STEP 6
Repeat steps 1-7 for plugs on 2 & 3.
STEP 7.
To remove Plug #4 which is the last plug on the passanger side,you have to remove the two (2) 1/2inch bolts that holds a bracket to the exhaust manifold. Make sure you spray the studs these bolts are on with some DW-40 or liquid wrench. The exhaust manifold studs might have a lot of rust & being difficult to turn nuts off without shearing off the stud. It has some sort of aluminum box ontop of this bracket with some sensor wires coming out of it, Slip the bracket off and simply lay it to the rear of the engine to provide better access to this last cylinder.

STEP 8.
Repeat steps 1-7 for plug #4 and then Remount bracket containing the aluminum box with sensor wires.

Upon completion of the passenger side,you now have to proceed to the driver side.
STEP 1. The first cylinder at the front of the engine the spark plug wire has a grey handle sticking up next to the A/C compressor. Using some pliers (needle nose plier) twist & pull this grey handle. The spark plug boot should pop out.

STEP 2.
With the help of the small flat edged screw driver, unhook the spark plug wire clips that hold the wires together. There are 3 - One just after the 1st coil pack located at the front of the engine, another just on the other side of the valve cover and a small 2 clip located about 1/2 way back on the valve cover under the intake manifold.
STEP 3.
Remove the spark plug wire from Cylinder #1 on the Drivers side
STEP 4.With the help of the small flat edged screw driver,press the 4 connection points on the grey handle that is attached to the wire,it will separate down the middle and allow you to remove the wire, Replace the wire with the new wire,you have to ensure you line up the rubber round plugs with the round holes in this grey handle & snap it back together with the new wire in place.

STEP 5.
Hold the spark plug socket in your left hand down near the plug,feed a 6" inch extension below the A/C Compressor line (black pipe) and the A/C Compressor with your right hand and attach the spark plug socket into the extension.
STEP 6.Slip the socket onto the plug,afterwards,attach an additional 3 or 6 inch extension to the existing extension & attach your socket wrench.
STEP 7.Remove the plug & proceed to replace it with a Bosch Platinum plug & anti-seize on the threads. Feed the new Spark Plug wire over to the 1st coil pack & replace it on the coil pack.

Jul 05, 2011 | 1997 Ford Ranger SuperCab

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

3 Answers

How to change spark plugs


Those are as easy as they come these days. Mark each spark plug wire with a piece of tape with the cylinder # written on it, so as not to mix up the wires. Remove each spark plug wire by firmly grasping the wire by the boot (do not pull on the wire) and twist it back and forth a few times while pulling slowly. It should pop off without a great deal of effort. If it is seized and it breaks, you will have to replace the wire, or at the very least replace the terminals (if you can get some). Use an air hose and blow around the base of each spark plug to dislodge any loose dirt that could fall into the cylinders (not absolutely necessary, but a good idea). Remove each spark plug with a spark plug socket and extension and ratchet (I forget which size socket, it's either 5/8 or 13/16). Check the gaps of each new spark plug (typically around 0.035 in). re-install each new spark plug by hand (do not cross-thread them) and once you have ensured that the plug is threaded in properly, tighten the plug until it seats, and then tighten an additional 1/16 of a turn. Repeat this for the remaining plugs. Re-install wires to the corresponding spark plugs. You're done!

Jan 10, 2011 | 1983 Ford Crown Victoria

1 Answer

How do I change the spark plug of the dodge magnum 2006


· Open the hood and remove the bolts that hold the engine cover in place, if your Dodge comes with an engine cover (depending on model and year). If so equipped, pull the cover off the engine.

· 2

Grab a spark plug wire by the base of the wire and pull the wire up and out of the engine. (You may need to wiggle it back and forth while pulling up on it to get it out of the engine.)

· 3

Trace the wire back to the power distributor and pull the spark plug wire off the distributor. Make a note of the plug orientation.

· 4

Install the new plug wire in the place of the removed one. Match the new wire with the old one to make sure they have the same size. Press the plug wire over the distributor electrode and onto the spark plug firmly, so that the ends are secure. Installation is the reverse of removal procedure.

· 5

Repeat the above procedure for all the other spark plug wires. It is best to change all the spark plug wires at the same time.

Sep 29, 2010 | Dodge Magnum Cars & Trucks

1 Answer

Where to place the spark plug wires on ? there are numbers on the box & KW on the wires. Which belongs to which?


You would usually remove one wire at a time and match up it's length to a new wire, then do the second, third, etc, You should have them all fitting and in the right places by doing it this way. If you take them all off at once, you will be back on here asking for the wiring diagram. I don't know what the KW stands for or the numbers. Hope this helps.

Aug 13, 2010 | Ford Explorer Sport Trac Cars & Trucks

1 Answer

NEED TO TAP INTO BRAKE WIRE FOR INSTALLING TRAILOR (WITH BRAKES) ADAPTER ONTO MY 2007 JEEP GRAND CHEROKEE. NEED WIRING DIAGRAM OR WHERE IS EASIEST PLACE AT REAR OF VEHICLE TO TAP INTO BRAKE WIRING CIRCUIT?...


DONT CUT WIRES! Go to your local parts store and purchase an inline adapter.there is a plug(inline)at rear driver side, unplug,install new adapter,supplied info w/adapter will tell you the rest.

May 01, 2010 | 2007 Jeep Grand Cherokee Overland

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

I have a 2001 Ford Windstar w/3.8 V-6. The codes state that #5 cyl has a misfire. I just changed the plugs, put new plug wires on & installed 4 new O2 senors. What else should I be looking for?


Double check the plug wires, if the boot to the plug wire was not installed with spark plug boot lube. It may have pulled away from the plug just enough to make it a bad connection. Go back and push on the plug wire boot to the spark plug and make sure the wires are routed properly and not touching anything other then the separator that hold the wires in place. The other thing would be a dirty injector ir an bad wire to the injector. Start with te plug boots and routing. Good luck friend, I have a Montana and same thing here, take me longer to ensure that all the plug wires are set then to replace the plugs. 

Jul 03, 2009 | 2001 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...