Question about 1995 GMC Sierra C1500

1 Answer

4 wheel drive will not engage

When i push the button for 4 wheel drive on the dash it just blinks a couple of times and nothing happens. the truck drves perfect in 2 wheel drive, what could make this happen?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 88 Answers

The engagement piston might be dirty causing it not to fully engage. Also check your linkage on your transfer case.

Posted on May 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy push button wheel drive


check the vacuum lines to the actuator in the front wheels . check the actuator operation in the transfer case.

Feb 15, 2014 | Cars & Trucks

1 Answer

It started with pulling 4 wheel drive lever to engage 4 wheel drive.It would take couple of seconds to engage.Finally engage light would appear showing engage.The light would blink a few times before...


Check the linkage under the vehicle that goes from your shift lever to a rod that then goes to the transmission lever. Sometimes a coupling will come loose. Simple return it to its' original position and re-tighten. Let me know if this helps. Thanks.

Dec 22, 2010 | 1995 GMC Suburban

1 Answer

How do I use the 4 wheel drive on my GMC Yukon 2004. What dash button turns the 4 wheel drive on?


Hi, depending on the vehicle, there can be different controls. Standard control, 4hi, use in slippery conditions, never on dry pavement. Just push the button, and it will engage. 4low is for extreme conditons and the transmission must be in neuteral to engage 4lo. If you have auto 4wd button, just press the button in slippery conditions. If you have a denali, it is all wheel drive, and there are no buttons to push. So, depending on the model, there are multiple ways, but pushing the button engages it. Good luck...Goop

Dec 12, 2010 | 2001 GMC Yukon XL

1 Answer

My truck was engaged into 4 wheel drive lo and now it will not engage into anything else. It is a 2004 silverado with push button 4 wheel drive.need to know where my acuator and module is located to see if...


Your transfer case encoder motor [the thing that shifts the transfer case] is located on the LH side of the transfer case. I believe the control module should be located behind the dash near the light switch area.
If it stays in 4-Lo and the push button indicator just flashes for a while when you select, say, 2 Hi then stops blinking and goes back to the 4-Lo position then I would have someone hook up and check to see what service codes are present. I see a lot of encoder position sensors go bad but you really need a scan tool hooked up to the system to be able to watch what is happening as the shift is attempted. There aren't any vacuum controls on this system.
Hope this helps you out a bit!

Nov 28, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

2001 2500 suburban , will not always engage into 4 wheel when button is pushed , nothing happens , then when it does sometimes it will not go back to 2 wheel drive .


There is an electrical conection called a servo and this might need to be replaced. It actuates the 4 wheel drive when the button is depressed

Feb 16, 2010 | 2004 Chevrolet Suburban

1 Answer

Our 2006 f150 4 wheel drive won't engage- dash


I had the same thing happen this weekend.Ij ust talked to my service man and he said if all the fuses are good it might be the switch on the dash.

Jan 24, 2010 | 2006 Ford F-150

1 Answer

4 wheel drive doesn't work


sounds like the shift motor on the transfer case is going bad.

Aug 29, 2009 | 2004 Chevrolet S-10

1 Answer

4 wheel drive does not engage


run a direct hot wire to axle concetion might get lost when moved if nothing take out your lockouts & re build or replace

Dec 17, 2008 | 2000 GMC New Sierra 1500

1 Answer

2000 jimmy stuck in auto 4 wheel drive


when can you engaged auto 4wheel drive and how long can you run it

Dec 03, 2008 | 2001 GMC Jimmy

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...