Question about 2000 Honda Civic

1 Answer

Steering wheel removel with air bag

How to remove steering wheel with air bag on 2000 honda civic

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 79 Answers

Air bag has bolts on the back of the steering wheel and to remove the wheel you will need a steering wheel puller but keep all of this because without the factory airbas it will not pass inspection

Posted on May 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to replace tumbler 1993 honda accord 5-speed


That is not the key part of the switch, it is the electruical switch the key cylinder operated.
Instructions
    • Set the front wheels to point forward and remove the key from the ignition.
    • 2Disconnect the black battery cable and then the red battery cable, in that order, using a wrench unfasten the two torx bolts securing the lower lid on the steering wheel using a ratchet and torx bit. Pull off the red shorting connector from the underside of the lid and put the lid aside.
  • 4Reach through the steering cover opening, unplug the air-bag electrical connector and insert the red shorting connector to the air bag side of the unplugged connector.
  • 5Unfasten the three glove-box mounting screws and put the glove box aside using a Phillips screwdriver.
  • 6Unplug the passenger air-bag electrical connector and insert the red shorting connector located next to the connector into the air-bag side of the unplugged connector.
  • 7Pry off the small cover behind and on each side of the steering wheel using a small flat-head screwdriver.
  • 8Unfasten the torx bolts under the small covers using a ratchet and a T30 torx bit and remove the bag assembly from the steering wheel. Place the bag in a safe place away from your working area with the cover facing up.
  • 9Unplug the horn connector located on the upper side of the steering wheel assembly and the cruise control switch located off center and towards the right of the steering wheel assembly.
  • 10Make alignment marks on the steering column shaft, at the center of the steering wheel, and the steering wheel assembly so that you can reinstall the steering wheel in the same exact position. Use a marker.
  • 11Unfasten the steering-wheel retaining nut on the center of the assembly using a ratchet, ratchet extension and socket. Hold the steering wheel steady with one hand as you remove the retaining nut.
  • 12Rock the steering wheel carefully from side to side as you pull the wheel off the center shaft. If the steering wheel is stuck, install a steering wheel puller on the assembly and detach the wheel from the shaft.
  • 13Remove the upper and lower steering column covers using a Phillips screwdriver.
  • 14Unplug the ignition switch connector.
  • 15Insert the key into the lock cylinder and turn the key to the "On" position.
  • 16Unfasten the two ignition-switch mounting bolts from the steering column using a ratchet, ratchet extension and socket. Then remove the switch from the steering column
  • Aug 09, 2012 | 1993 Honda Accord

    1 Answer

    How to remove steering wheel, 2000 blazer


    Parts stores sell an inexpensive steering wheel removal puller. Follow repair manual removal procedure, so the air bag doesn't activate. The steering wheel is retained by a large nut on the steering wheel shaft. Remove the nut, and attach the puller to wheel-it should pull right off.

    May 16, 2012 | 2000 Chevrolet Blazer

    1 Answer

    My SRS light is on. The horn and Cruise control doesn't work. Could this be more than a fuse?


    Most likely issue is the "clock spring", Located in the steering wheel. They can be replaced but if your not sure about messing with the air bag in the steering wheel, that work is best left to a repair shop.

    Mar 31, 2011 | 2000 Honda Civic

    1 Answer

    How do you remove the steering wheel on a 2000 Chevy Silverado?


    Hi there,

    Reach behind, there are 4 screws. Remove these screws and pull of air bag assembly. Make sure negative battery cable has been disconnected for 10 minutes and SRS fuse has been pulled. Once the air bag assembly is off, pull the horn wire off, then remove steering wheel nut and washer and pull of the wheel.

    Good luck...

    Jan 16, 2011 | 2000 Chevrolet Silverado

    1 Answer

    Needs key cylinder replacement


    This first post is WITH AN AIR BAG:



    With Air Bag Before removing the steering wheel, disable the air bag system
    Disarming the System To disarm the air bag system, simply disconnect the negative battery cable from the battery. Isolate the battery cable by taping up any exposed metal areas of the cable. This will keep the cable from accidentally contacting the battery and causing deployment of the air bag. Allow the system capacitor to discharge for at least 2 minutes, although 10 minutes is recommended, to allow for the dissipation of any residual energy.

    CAUTION Before removing the steering wheel, disable the air bag system (refer to Section 6). Failure to do so could result in accidental air bag deployment and possible injury.


    1. Disconnect the negative battery cable and disable the air bag system.
    2. Set the front tires in a straight-ahead position.
    c0447ef.gif
    Exploded view of the air bag module mounting

    1. Remove the air bag module retaining nuts from behind the steering wheel.
    2. Remove the air bag module.
    3. If equipped, remove the cruise control switch.
    4. Disconnect the horn wiring.
    5. Remove the steering wheel retaining nut.
    6. Scribe a line mark on the steering wheel and steering shaft if there is not one already.
    1c64d39.gif
    Use a puller to separate the wheel from the column

    1. Remove the steering wheel using a suitable puller.
    To install:
    1. To install, align the scribe marks on the steering shaft with the steering wheel.
    2. Ensure the wheel compresses the 2 locktabs on the clockspring.

    Oct 11, 2009 | 1993 Jeep Grand Cherokee

    1 Answer

    Airbag deployed


    SECTION 501-20B: Occupant Restraints — Passive — Supplemental Air Bag System 2000 Villager Workshop Manual REMOVAL AND INSTALLATION Module —Driver Air Bag Removal
    syv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The backup power supply energy must be depleted before any air bag component service is performed. To deplete the backup power supply energy, disconnect the battery ground cable and wait three minutes.
    NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again. If the vehicle was in a frontal collision and the air bag did not deploy, the air bag may not have been needed. Complete a diagnosis of the air bag system before installing a new driver side air bag module (043B13). Refer to Diagnosis and Testing in this section.
    1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
    1. Remove the two driver air bag module retaining bolt access covers (one shown).
    1. Remove the steering wheel bottom cover to access the driver air bag module electrical connector.
    1. Disconnect the driver air bag module electrical connector.
    1. syv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: After removing, discard the driver side air bag module bolts and install new driver air bag module bolts during installation.
      Remove the two driver air bag module retaining bolts (one shown) and discard.
    1. Remove the driver air bag module.
      1. Separate the driver air bag module from the steering wheel and disconnect the horn pad switch.
      1. Remove the driver air bag module.

    Apr 16, 2009 | 2000 Nissan Quest

    1 Answer

    Removing steering wheel


    It's actually more simple than you think. First disconnect the negative cable from you car battery. then remove the plastic housing around your steering column. Next disconnect the air bag harness from it's plug. What ever you do don't apply any electrical testers or live circuitry to any of the air bag components and wirings. There should be two screws on the back side of your steering wheel. Remove these and the rest should be self explanitory.

    Nov 23, 2008 | 1996 Honda Civic

    2 Answers

    Blinkers wont click off automatically?!


    Probably not a switch problem.
    Most turn signals are reset via a mechanism actuated by a finger attached to the hub of the steering wheel and acting on a switch actuator that is set when you choose left or right blinker.
    The entire assembly is probably plastic and some are quite fragile.
    Unfortunately, removing the steering wheel to replace or shim anything requires the removal of the hub-mounted air bag and this is something better left to a Honda service tech instead of risking the $6-700 air bag and a black eye or two.

    On a vehicle with working turn signals but the motor & radio off, try setting the signal with the wheel centered, then turning it in the direction signaled.
    You will hear one or more clicks when the resetting mechanism is engaged.
    You will not hear that on your car.

    May 21, 2008 | 1996 Honda Civic

    Not finding what you are looking for?
    2000 Honda Civic Logo

    Related Topics:

    224 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    76673 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...