Question about Cars & Trucks

Open Question

How do i remove the rear parking sensors from the bumper of a 2005 citroen c3

One of the sensors is faulty and just screams all of the time, but the are no very easy to get at, if I can find the problem one for now I will just disconnect it.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

Ad
  • 77 Answers

SOURCE: how to remove the rear bumper on a 2005 Kia Sedona

1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Posted on Jan 30, 2010

  • 92 Answers

SOURCE: I have a 2006 Ford Explorer and 2 of my park aid

You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Posted on Apr 03, 2010

  • 52 Answers

SOURCE: how to replace a bmw rear parking sensor

put car into reverse with ignition on (not running) and either listen very closely or feel each sensor with your finger tips, you should hear a clicking noise or feel a ticking on the good sensors. once you have determined the faulty one simply release the two plastic retaining clips and push the sensor through the bumper inwards, then remove plug and fit new sensor

Posted on Apr 29, 2010

  • 4793 Answers

SOURCE: Volkswagen Passat rear bumper removal

all the screws/bolts are underneath the plastic cover.hex head.(allen key)

Posted on Jul 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removal of broken rear parking sensor on Citroen C6 2007 Exclusive


Most Citro?n models require the bumper to removed to access the parking sensors, this sometimes incurs the removal of the rear lights and inner wheel arch trims to reach screws to remove.

Oct 26, 2016 | Citroen Cars & Trucks

1 Answer

Difficulty starting, blowing white smoke, engine light on


run the fault codes to check for faulty sensors

Oct 25, 2015 | 2005 Citroen C3 Pluriel

1 Answer

Removing jaguar s type rear bumper..


disconnect the connector from the park aid module push the connector and grommet out of the back panel remove screws from lower rear of wheel arch liners remove boot floor trim remove plastic boot closing panel trim remove both boot side trims you wil find a number of 10mm headed bolts around the boot at the sides and back remove these and get someone to help you remove the bumper liner the 2 outer sensors can normally be changed without removing the bumper liner on some models

Mar 26, 2013 | 2003 Jaguar S-Type

1 Answer

05' Grand Caravan, told that 2 of the rear bumper parking sensors need to be replaced. What is the proper term for these, as I can't find them anywhere, and how invasive to replace?


I wish I had good news but rarly does this sensor go out. unless someone rear ended you. in this case the bumper cover has to be removed.

Dec 20, 2011 | 2005 Dodge Grand Caravan

1 Answer

The park assist system switches itself off after a minute. Problably a faulty sensor? But how to find out wich one is bad end how can they be removed out of the bumpers of my 2005 ML270cdi?


Yes it does sound like you have a faulty sensor, If you're in the NY area I'd have a look at it for you. If you're not then you'll need to find someone with the mercedes benz computer (SDS) to find out exactly which sensor is defective. Through the computer it's possible to test each sensor individually to see which one is not working. I'm not 100% sure on this, but I believe there's a very good chance you'll have to remove the bumper to get the sensors out and they are clipped into a housing in the back of the bumper. Hope this information helps.

Please don't forget to rate my answer. Thank You.

Jun 12, 2011 | 2005 Mercedes-Benz M-Class

1 Answer

How to replace a bmw rear parking sensor


put car into reverse with ignition on (not running) and either listen very closely or feel each sensor with your finger tips, you should hear a clicking noise or feel a ticking on the good sensors. once you have determined the faulty one simply release the two plastic retaining clips and push the sensor through the bumper inwards, then remove plug and fit new sensor

Apr 28, 2010 | 2003 BMW 325

2 Answers

I bought a 2005 Dodge grand caravan sxt. The overhead info center tells me service park assist system. Most of the time it works great but sometimes when i am driving the message pops up and then it stops...


faulty sensor in teh bumper or bad connection, im not sure where the main module is on them. most likely in rear pannel, dr or pass side, check for rock beaten wires under the back of the van.

Sep 23, 2009 | 2005 Dodge Caravan

1 Answer

2005 Lincoln Navigator. Message says to Check


Most likely the problem you are experiencing with the park assist is a fault in one of the sensors mounted in the rear bumper. I would not consider it to be a major fix, however there will be a few hours labor involved as the bumper cover needs to be removed to replace the sensors.

Jul 07, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...