Question about 1992 Isuzu Rodeo

1 Answer

Blinkers on my '92 Isuzu rodeo are not working--ANY IDEAS??

I just bought a 1992 isuzu rodeo and my blinkers are not working. Both of my blinkers and the blinker arrows inside the dash board are not lighting up. However, It still makes the noise of the blinker. My roommate suggested that it my be a problem with one of the fuses. I checked all of the fuses in both the fuse box under the steering wheel and the fuse box under the hood. I don't know a whole lot about cars so I was just wanting to know what specifically to look for. What a burnt fuse looks like and the fuse name that controls my blinker lights. If you can help that would be great! Thank for your time!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I don't know the correct test proceedure to idenify the problem before you purchase a switch In more cases than not the problem with the turn lights on the rodeo's comes down to a bad turn switch. Before spending $150.00 fo the part, I would check fuses which you did, check the flasher, check the bulbs, it would more than likley not be that all of the bulbs are inoperative but stranger things have happened. I fou are hady with a 12 volt light tester you may be able to check to make sure that you have power going to the switch, this would be easy if you can removed the stearing wheel and the plastic shroud around the collum as the wires and contacts are on the left side.

To be honest, Ididn't run any test as i was sure that the switch was bad from viewing the posts on the forum and several of them had the same issues.

Good Luck
dhopper




I just bought a 92 too around three weeks ago and the left turn signal made noise sometimes as it would make a regular blinker noise, but most of the time it would buzz when you turned the left turn signal on. The light on the dash would not work as well. There are several post on the fourm about bad switches and they seem to be a problem for this vehicle.
I tired to find a used one but could not. I purchased one on line from the Partswarehouse and installed it yesterday and everything works as it should.

There is one phillips head screw on the back side of the horn pad to remove and the horn pad should slide off, unhook the horn ground wire

Remove the steering wheel retaining locknut. I was able to bump the back side of the steering wheel with the palm of my hand around 4 times firmly and the steering wheel popped off. In some cases you may have to rent a wheel puller from Advanced Auto or Autozone if you run into difficulty.

Remove the plastic cover from the column , there are around 6 phillips head screws on the under side and the casing has two clips one each side the should snap out with a little pressure.

Remove the two screws form the Turn switch and unhook the harness plug and then reverse the proceedure to install the new switch.

This took me approximately 30 minutes to replace from start to finish,

Posted on Aug 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flasher repair


First, check your bulbs by starting up the vehicle and turning on the blinkers, then go around to check them. Also check to see if your emergency flasher work.
The fuses are either behind the glove box or under the dash on the driver's side.
Look on fixya, someone had the same problem back in April and several ideas were posted.
Good luck!

Jul 01, 2014 | 1995 Isuzu Rodeo

1 Answer

Blinkers


It should either be in your fuse box inside your car but most likely it will be inside the engine compartment in a black box and labeled.

May 27, 2010 | 1997 Isuzu Rodeo

1 Answer

Both Blinkers Blink when try to turn???


You have one of three problems :Condisation, weak ground or a frad wire in you collam

Jun 01, 2009 | 1998 Isuzu Rodeo

1 Answer

Blinkers not working


The buzzing sound is probably your relay. It is in your fuse panel and it is what controls how fast your blinkers flash. It is usually a round plastic thing in the fuse panel. and you replace it just as you would a fuse just pull the old one out and push the new one in

Dec 22, 2008 | 1992 Isuzu Rodeo

1 Answer

Isuzu Rodeo Photo Cover fuse


my fuse for the rear tail lights keeps blowing after 20 sec,

Nov 30, 2008 | 1992 Isuzu Rodeo

1 Answer

1998 Rodeo Transmission Speed Sensor


You need to replace the speedometer gear that drives the sensor.

Nov 28, 2008 | 1992 Isuzu Rodeo

1 Answer

92 Isuzu Rodeo Power loss


Do you have the v 6 or the 4 cyl.?
You may want to check the cap and rotor, and check to make sure all elctrical connections and vacuum hoses are tight and in good condition. Then go from there.

Jul 06, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

547 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...