Question about 2007 Kia K2700 Workhorse

Open Question

Brakes failling on Kia 2.7 workhorse

Brake pedal suddenly went hard when applying brakes

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 350 Answers

SOURCE: 2002 kia sportage 2wd brakes sticking

hi check all your brake linnings for contamination especially brake fluid on the linnings if this is ok you have a build up of pressure if its possible for you drive till the brakes start to lock up get out go to each wheel see if any of them is getting hot if so the problem is on that wheel jack it up to see if the wheel is locking if its red hot it will be sticking then try the rest of the wheels one at a time jack them up see if its one wheel or all if its one wheel release the bleed nut on that wheel see if it releases if it does it must be fitted with a pressure regulator to that wheel replace it . now if its all wheels its more likely to be the brake master cylinder or if fitted pressure regulator that supplies all the wheels a long shot i cannot see but better to mention it the brake pedal is not sticking and holding down yates210456

Posted on Sep 29, 2008

Ad
localwonder
  • 6784 Answers

SOURCE: Brake Fluid Type? 2000 KIA Sephia

any aftermarket brake fluid will be fine. the actual grade is located on the top of the fluid cap. you can find the universal grade at your local auto parts shop.

Posted on Mar 01, 2009

localwonder
  • 6784 Answers

SOURCE: the Abs light came on and will not go out after i

This is just a consequential event. the ABS sensor module was probably going out and decide the trigger the alarm at the same time you initiated the hard brake during travel. replacing or resetting this sensor module Will fix this issue. the light will go off as well.


Please rate and god bless.

Posted on Mar 17, 2009

  • 14036 Answers

SOURCE: brake pad replacement problems

get haynes repair manual.dont cost much .it got pictures .and it show you step by step .to change front disc brakes.

Posted on Mar 23, 2009

  • 1 Answer

SOURCE: 2006 Kia Sorento Brake Lights not working

Apparently this is a recall matter and will be fixed at no charge. KIA Consumer Assistance Center 1-800-333-4542. Recall notices were to go out in May/June 2009.

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hard pedal on a 1968 cadillac and brake light comes on


The most obvious cause for a hard pedal is simply not enough vacuum. check the vacuum. please go to this site for info on hard brake pedal= .mpbrakes.com/techtalk/how-to-series/how-to-diagnosing-a-hard-brake-pedal Goopd-Day!

May 21, 2014 | 1970 Cadillac Fleetwood

1 Answer

Why is it so hard to apply brake pedal?


_______power brake booster, check vacuum to booster and the check valve for brake booster. primary symtom is high hard pedal that requires greater then normal pedal pressure to stop car. testing booster= pump brakes several times with engine off to deplete stored vacuum. turn on engine with pushing slightly on brake pedal. you should be able to feel the pedal fade away a bit, and then become firm. But not hard. if you feel nothing at the pedal when engine starts. Brake booster is not working. Good-day! make sure vacuum is going to booster with engine running. it may just be a bad vacuum line or check valve.

Apr 30, 2014 | 1984 Buick Skyhawk

1 Answer

2005 kia optima abs& brake light ON


Try the master cylinder if that's not it try the brake booster, but first bleed all the brake lines starting with the driver rear then move forward if no pedal then proceed to master and booster

Jan 04, 2014 | 2005 Kia Optima

1 Answer

Isuzu trooper diesel piping diagram


when your brakes get hard 99 % of the time it is the brake booster if they get soft or spongy it the master cylinder

Aug 15, 2013 | Cars & Trucks

1 Answer

2009 Dodge Caliber - The ABS & Brake Light came on as well as the feeling/sensation of the brake being applied very hard for a split second.


take it to an accredited brake specialist shop
I suspect that the brake booster is becoming defective and the small application to the pedal causes excessive booster reaction
the abs section only maintains applied brake fluid pressure as set by the position of the pedal
that is to maintain the pressure as the stopping and start movement of a skidding wheel opens and closes a valve to that wheel /s
if you are on ice that sudden hard braking will cause the wheels to lock and immediately the abs cuts in to allow the wheels to turn and then to allow brake action to be reapplied
if the abs is working under brakes you will get a pulsating feeling under your foot as the fluid pressure is alternation between full on and released by the abs valves

Apr 01, 2017 | 2009 Dodge Caliber 2.0

1 Answer

Brake pedal went straight to the floor without resistance


Low or empty brake fluid . No red brake light lite . Brake line corroded maybe , where do you live ? Rust belt USA . Just had a similar problem in a 2005 chevy cavalier . Did you have to stop really fast ?

May 09, 2017 | 2003 Chevrolet Cavalier

1 Answer

95 f350 hard brake pedal


did you get your brakes fixed? If so what was wrong?

Nov 05, 2011 | 1995 Ford F350

1 Answer

Brakes


If diesel, the vacuum pump is failling or has a leak

If gas, the servo is failling or again a leak some where.

It should be one of the above.

Regards

Lloyd

Dec 07, 2009 | 2000 GMC Sierra

2 Answers

I have a 1998 chevy s10 it has a good brake pedal with the engine off but with it running the pedal go'es to the floor and you can hear air at brake booster


Check for fluid leaks and your brakes. If you see no leaks and your brakes are in good shape replace the brake master cylinder and bleed the system. The air you hear is because the pedal went to the floor. If the booster goes bad the pedal will get so hard you can hardly push it at all. I think you will find if this happened suddenly either you have a major leak or the master cylinder went bad.

Sep 29, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Shake in steering wheel


Sounds like your brake rotors.You dont have to feel it in the pedal to get a shake in the wheel.

Nov 26, 2008 | 2004 GMC Savana

Not finding what you are looking for?
2007 Kia K2700 Workhorse Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...