Question about Kia Cars & Trucks
Lampu ABS menyala.. apakah yang harus dilakukan.?
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: mazda tribute abs fault. abs
These vehicles have a recall on the ABS system for faulty wiring. You may want to check with your local dealer to see if your vehicle is included.
Posted on Sep 20, 2008
SOURCE: ABS signal light comes on
The front left and right ABS wheel speed sensors need to be replaced together. If you just replace the drivers side or passenger side, the light will come back on. If you are experencing ABS shutter, or when you apply the brakes, the ABS unit will activate the affected wheel, causing a horrible noise and feeling in the brake pedal/ steering wheel, one or both of the sensors are transmitting confusing data back to the pcm, causing a false " wheel lock signal" activating your ABS module.
These sensors are fairly easy to replace for someone that has done car repairs. I did both of mine on a Saturday morning, took 3 Hrs. I would only replace them with genuine Chrysler parts.
Posted on Feb 28, 2009
1. check and make sure that your tires are inflated to the correct pressure
2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.
3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.
4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.
As for the ABS light, that means your antilock brake system has detected an issue such as a block sensor, or a faulty relay, etc.. when this light is on, it means that your abs may not engage when it should, or may engage when it shouldn't.
Posted on Aug 21, 2009
The simple DIY method is to gently hose down each wheels when they are COMPLETELY COLD.
Dirt can cover to ABS sensors.
Most failure are from the front wheels because of the heat.
The car wash with under side cleaning will also do the trick if it's a dirt related problem.
Remove the negitive battery cable or clear the OBD-II code.
MAC and OTC make ABS senor tester to pin point the trouble spot but it cost $$$.
Do the preventive cleaning before bring it to the shop.
Please post more information after you clean out the wheel sensors.
Posted on Aug 23, 2009
it means you need to have it daignosed, you have a malfunction in the ABS brake system, could be anyone of a number of things, abs module, wheel sensors, etc...
Posted on Nov 02, 2009
Tips for a great answer:
Oct 18, 2016 | Cars & Trucks
On vehicles equipped with antilock brakes (ABS), a second warning light is provided to warn if a problem occurs within the ABS system. The ABS lamp comes on when the ignition is turned on for a bulb check, then goes out after the engine starts. If the ABS warning light remains on or comes on while driving, it indicates a fault has occurred in the ABS system.
What happens next depends on the nature of the fault. On most applications, the ABS system disables itself if the ABS warning light comes on and remains on.
Oct 24, 2012 | 1999 Ford Ranger SuperCab
Aug 20, 2011 | 2007 Toyota Camry
Mar 03, 2011 | 1992 Pontiac Sunbird
Oct 24, 2010 | Buick Century Cars & Trucks
Aug 16, 2010 | 2001 Chevrolet Silverado
Jul 28, 2010 | 2001 Buick LeSabre
Feb 20, 2010 | 2002 Ford Escape
Jul 09, 2009 | 2003 Audi TT
24 people viewed this question
Usually answered in minutes!