Question about 1995 Chrysler New Yorker

1 Answer

Timing off I have 1995 new yorker 3.5 eng. the problem is the tensioner that holds the timing belt bolt broke off . I fix the bolt but I don't know if timing in the all engine move , if that happen how can i fixed.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 6,674 Answers


Align the camshaft sprockets between the marks on the covers,behind pulley's


Align the crankshaft sprocket with the TDC mark on the oil pump cover.

Posted on Jul 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a serpentine belt on my 1990 new yorker


Write a diagram of the pulleys and belt direction release the tensioner or alternator adjusting bolt remove old belt and fit new one, check idler pulley bearings for noise and wear.

Nov 15, 2014 | 1990 Chrysler New Yorker

1 Answer

How do i change a waterpump on a 2001Volkswagen cabrio?


Your Cabrio has one of several 2.0L Volkswagen engines - determine your engine type from the
8th digit of your VIN, which will be either an "A", or "C",both are 2.0L engines.

Volkswagen 2.0L engines offered in 2001:
(a) 2.0L (Aba) Engine
(b) 2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine
(c) 2.0L (Aeg/Avh/Azg/Bdf) Engine

For completeness, I've included the water pump maintenance manual entries for all (3) 2.0L VW
engines offered in 2001. Note that the instructions below include (3) illustrations, which are
reproduced faithfully from the manual, but the last (2) illustrations are identical, since the last two
engines in the list above are virtually identical.

Volkswagen 2001 engines - water pump replacement

2.0L (Aba) Engine

Before servicing the vehicle, refer to the Precautions section.

Remove or disconnect:

1. Coolant

2. Thermostat housing from under the water pump housing.


Loosen but don't remove the bolts holding the pulley to the water pump.

Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing.


To install:


Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



archaeology_93.jpg

Fig. Water pump and thermostat housing-2.0L (ABA) engine

1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Coolant

Thermostat housing from under the water pump housing.



3. Loosen but don't remove the bolts holding the pulley to the water pump.

4. Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing. Refer to figure of ABA engine's water pump above.

To install:

1. Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

2. Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

3. Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine


1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Negative battery cable.

Coolant.

Accessory drive belt and tensioner.

Upper and center timing belt covers.



3. Position the engine so that the No. 1 cylinder is at TDC.
WARNING
Cover the timing belt to protect it from being contaminated with coolant.


4. Loosen the timing belt tension and slide the belt off the water pump sprocket.

5. Remove or disconnect:

Timing belt guard (2) mounting bolt (1), if equipped.

Water pump mounting bolts (5), then the water pump (4).

O-ring (3) and clean the seating area.


To install:



archaeology_94.jpg



Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine

1. Install or connect:

O-ring, moistened with coolant.

Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

Timing belt guard, if equipped. Mounting bolt: 15 ft. lbs. (20 Nm).

Timing belt.

Upper and center timing belt covers.

Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

Accessory drive belt.

Coolant.

Negative battery cable.



2. Check and clear any DTCs, then match the ECM to the TCM.


2.0L (Aeg/Avh/Azg/Bdf) Engine


1. Before servicing the vehicle, refer to the Precautions section.

2. Remove or disconnect:
1. Negative battery cable.

2. Coolant.

3. Accessory drive belt and tensioner.

4. Upper and center timing belt covers.


3. Position the engine so that the No. 1 cylinder is at TDC.

WARNING
Cover the timing belt to protect it from being contaminated with coolant.

Loosen the timing belt tension and slide the belt off the water pump sprocket.

Remove or disconnect:

1. Timing belt guard (2) mounting bolt (1).

2. Water pump mounting bolts (5), then the water pump (4).

3. O-ring (3) and clean the seating area.


To install:



archaeology_95.jpg


Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine


Install or connect:

1. O-ring, moistened with coolant.

2. Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

3. Timing belt guard. Mounting bolt: 15 ft. lbs. (20 Nm).

4. Timing belt.

5. Upper and center timing belt covers.

6. Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

7. Accessory drive belt.

8. Coolant.

9. Negative battery cable.


Check and clear any DTCs, then match the ECM to the TCM.

Sep 13, 2011 | 2001 Volkswagen Cabrio

2 Answers

How to change the alternator in a 1995 Grand am Thanks


First unhook battery. Then unplug connectors and wire. Loosen bolts to take tension off of belt. Remove belt remove bolts holding alt. Place new alt in spot remember wich holes go where so not upside down replace bolts dont tighten yet. Install belt on all pulleys tighten tensioner bolt on alt bracket to snug tension after proper tension is achieved tighten all bolts and nuts. replace all plugs and wires reconnect battery pay attention to pos and neg dont hook up battery backwards. Congrats your done.

May 03, 2010 | 1995 Pontiac Grand Am

2 Answers

How to put a idler/tensioner pulley on


remove accessory belt ,remove center bolt holding pulley to front of eng. likely to be a 9/16 or a 5/8. To install new one, make sure you line up the dowl pin to the hole, install bolt. To reinstall belt will require either a 3/8 or 1/2 in. drive rachet or breaker bar to reduce tension allowing belt to slide on.

Apr 05, 2010 | 1999 Dodge Durango

1 Answer

Timing belt broke ,just replace it but it won`t crank.it sounds like electric priblem


Only the 2.3 liter diesel is an interference engine. The 2.3 Liter gas is not an interference engine. I would guess the belt was not installed correctly. The belt broke so the cam was then out of alignment with the crankshaft. Unless you aligned it correctly it will not start. BTW, the belt must be replaced every 60,000 miles. I asume you have the timing cover off, put it back on and set the crankshaft at the 0 mark on the timing cover, remove the cover and don't touch the crank. near the bottom of the cam gear is a protruding piece of plastic with three raised areas, set the cam timing mark at the first pointer, closest to the passenger side . on the back part of the timing cover is a v shaped pointer set the distributor gear mark at the pointer, remove the distributor cap and verify that the rotor is pointing at #1. Loosen both bolts on the tensioner and using a pry bar carefully pry the tensioner away from the distributor gear, tighten the small bolt on the tensioner. install the new belt starting at the crank, then the distributor gear, then the cam, then over the tensioner pulley. loosen the small bolt and the tensioner will adjust automatically. tighten the tensioner bolts and turn the engine over by hand 2 or 3 times and make sure all marks line up ( the cam mark should now be at the center pointer with the crank at 0). I find it handy to paint a reference mark for the crank inside the timing cover.

Mar 16, 2010 | 1995 Ford Ranger Supercab

1 Answer

How to fix a Belt Tensioner - '95 Pontiac Gran Am Se V6 3.1L?


UNSCREW THE BOLT THAT HOLDS IT TO THE ENGINE BLOCK.GET A NEW PART TO REPLACE IT.CHECK YOUR BELT CAREFULLY IT MIGHT NOT BE THAT GOOD.THERES A DIAGRAM IN THE ENGINE COMPARTMENT TO SHOW THE BELT ROUTEING.

Jan 26, 2010 | 1995 Pontiac Grand Am

1 Answer

My belt tensioner pulley broke at the bolt that bolts to the bracket. I bought a new one and I was wondering if there was an easier way to replace the tensioner pulley other than removing both the upper...


You should only remove the drive belt shield if you raise the car. Below are step-by-step instructions per the repair manual. Drive Belt Tensioner
Removal & Installation To Remove:
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the drive belt shield at the right wheel well.
  4. Remove the drive belt.
  5. Remove the drive belt tensioner mounting bolt.
  6. Remove the drive belt tensioner.
To Install:
  1. Install the belt tensioner. Torque the mounting bolt to 21 ft. lbs. (28 Nm).
  2. Install the drive belt.
  3. Install the drive belt shield.
  4. Lower the vehicle.
  5. Connect the negative battery cable.



Oct 30, 2009 | 1999 Plymouth Grand Voyager

1 Answer

1997 Buick Regal fanbelt problem


buy a new tensioner assembley and idler pully and might as well get a new belt while your at it. you will need a 3/8 ratchet a 15 mm socket and a 13 mm socket there is one bolt holding on tensioner remove it discard old tensioner put new tensioner in place and tight bolt. second remove bolt from idler pulley discard old pulley put inton place and tighen bolt. next install belt fallow belt routing digram put head of 3/8 rattachet into hole on tensioner or on bolt head of tensioner pulley depending on style of tensioner and pull or push to create slack in belt push belt into groves on all pulleys and release tensioner

Jul 31, 2009 | 1997 Buick.5 Regal

1 Answer

1995 ford taurus,broke bolt on tensioner pully while trying to replace belt, now what??


was this the bolt in center of the tensioner pulley? if so you will need to remove and replace the tensioner assembly, if not which bolt did you break?

May 26, 2009 | 1995 Ford Taurus

1 Answer

Do not know how to remove crankshaft pulley to replace timeing belt


Ignore smart a$$ comments.
Disconnect negative battery terminal.
Remove front right wheel.
Remove splash guard.
Place jack under engine.
Remove left engine support bolts from body.
Remove engine support plate bolts from engine.
Unbolt air conditioner pump and move it out of the way.
Get under vehicle and remove steering pump bolts and move it out of the way.
Remove 6 crankshaft pulley bolts, should be 12mm.
The engine support bracket shoud come off now.
Remove the main crankshaft bolt.
Remove crankshaft dampener.
Remove the timing cover bolts and take off the covers.
Take off the old belt & replace with a new one, don't use a previously used belt.
Make sure the belt tensioner is installed correctly.
Put all the stuff back on.
Get a Haynes manual, pages 3-41.

Apr 30, 2009 | Plymouth Voyager Cars & Trucks

Not finding what you are looking for?
1995 Chrysler New Yorker Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...