Question about 2000 Chevrolet Blazer

1 Answer

Removing the radiator from a 2000 chevy blazer 4.3 4x4 4door???

I am trying to find out on the internet how hard it is to remove the radiator from my truck to replace it. I am unemployed at the time and have not alot of money to go pay someone to do this so i am going to try and tackle this problem just need a little help!!! Anyone!!!

Thanks

Posted by on

  • cockfield May 20, 2009

    Thanks do you know if i need to plug the trans line when i disconect it from the radiator?
    Also do I need to take the radiator fan off also or will the radiator just slip out without touching the cooling fan?




×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 135 Answers

It is not that hard to replace the radiator. you can do it. remove negative cable from battery,drain radiator,remove top and bottom radiator hoses,remove transmission lines from the radiator, remove bolts in plasticradiator cover,remove all hoses connected to radiator, after everything is disconnected radiator will pull up and out

Posted on May 19, 2009

  • michael wiggins May 20, 2009

    it is better if you plug the trans. lines,if you remove the fan loosen the fan bolts and then remove the belt. if you had a lot of experience you could move the fan cover back and pull the radiator up. being that you are new at this remove the fan.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Chevy S10 Blazer Serpentine Belt replacement


You use a breaker bar to move the tensioner, remove the belt and use the tensioner to put it back. You draw the belt and pulleys on a sheet of paper before removing, otherwise there should be a small diagram of the belt and pulley positions on the fan shroud or radiator support.

Jun 25, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

A diagram of the flushing of a radiator and block of a chevrolet blazer LS 2000


Theres no such thing as a diagram, here are the draining instructions, hope this helps...
  • 1-Place a large drain pan beneath the radiator drain plug. The drain plug is located on the passenger side at the very bottom of the radiator on the engine side.

  • 2-Make sure the engine is cool. Open the hood of the truck and remove the radiator cap.
  • 3-Loosen the drain plug. On the 2000 Blazer, the drain plug is a wing-nut type of plug. Twist it with your fingers until the coolant begins to drain.

  • *To flush the block, once you have drained the radiator, run the engine for a bit untill the temp gauge goes up to normal, then the coolant will have been evacuated from the block. DO NOT leave the engine on, once it reaches normal temp, (this will happen quick) turn off right away, otherwise you'll be forking out a few hundred $$$ to fix the worped heads.
    4-Tighten the drain plug with your fingers once the coolant has drained fully from the radiator. Remove the drain pan and dispose of the used coolant properly.
    Some service stations will take and recycle your used coolant.
    Hope this helps...



  • Read more: How to Drain a Radiator From a 2000 Chevy Blazer ' eHow.com http://www.ehow.com/how_6357264_drain-radiator-2000-chevy-blazer.html#ixzz1VS4RBufX

    Aug 19, 2011 | 2000 Chevrolet Blazer

    1 Answer

    Removing dash board on 2001 Chevy Blazer to replace heater core. having problems with removing emergency brake cable.


    e emergency brake cable has to be removed at the pedal on the kick panel and not at the dash pay attention on removal and repeat steps to reinstall as it can be slid in from the front of the dash for new install but has to be removed in reverse steps

    Feb 27, 2011 | 2000 Chevrolet Blazer

    1 Answer

    I HAVE ANITFREEZE LEAKS FROM MY 2000 CHEVY S10 BLAZER. IT'S HARD TO TELL BUT THE LEAK SEEMS TO BE COMING FROM UNDER THE MOTOR RATHER THAN FROM THE RADIATOR OR ANY HOSE I CAN SEE.


    a common V6 failure is the intake manifold gasket. coolant will usually leak behind the water pump on the drivers side, however it can leak at other locations on the intake manifold gasket.

    coolant leaks from other areas include the heater core, hoses, expansion plugs, trans cooler, and coolant overflow tank.

    Jan 03, 2011 | 2000 Chevrolet Blazer

    2 Answers

    2000 chevy blazer (4.3 engine) has a hard time starting in the


    dirty fuel filter or faulty pump....just a guess...

    Feb 15, 2010 | 2000 Chevrolet Blazer

    1 Answer

    How do i replace tail lights on chevy 2000 blazer


    You have to open the trunk door and then there should be two screws for each light. If it's like mine then you have to pull off the hydrolic by removing the clip to get to the bottom screws. It's pretty easy.

    Aug 29, 2009 | 2000 Chevrolet Blazer

    1 Answer

    Rear speaker replacement on a chevy blazer


    You need to remove the rear seat there is no other way of taking them out without removing the rear seat

    Aug 15, 2009 | 2000 Chevrolet Blazer

    1 Answer

    Airbag removal 2000 Chevy Blazer 4.3l


    there should be 2 or 4 bolts/screws on the back of the steering wheel

    Jul 18, 2009 | 2000 Chevrolet Blazer

    1 Answer

    Removing fuel meter from plenium on 01 chevy blazer


    You are missing a bolt, or you will have to remove one of the heads.

    Dec 29, 2008 | 2001 Chevrolet Blazer

    Not finding what you are looking for?
    2000 Chevrolet Blazer Logo

    1,569 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7782 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...