Question about 2002 Chrysler Sebring

Open Question

Put new waterpump on 02 sebring with 2.7 set cam gears marks on straight up and lined with colored links also set crank mark with houseing on oil pump but wont start seemed to jump time is there an easy solution

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2001 chrysler concord 2.7 liter timing set

I have a similar problem. I just replaced the water pump and now the POS wont start. Like it is not getting fuel>

Posted on Sep 27, 2008

stevenhurc
  • 450 Answers

SOURCE: in replacing engine timeing belt,

no you will bend valves if not carefull. you can only turn over from crankshaft if timing marks were in correct position in first place.

Posted on Jul 02, 2009

  • 701 Answers

SOURCE: need to now where timing marks are located on 1997

Hello carolnaes: My name is Roger and I will help. The picture of the timing marks are attached. I will caution though that Mitchell repair calls this a interference motor. Meaning if the engine turns over with the belt off. The valves of the engine can and may be damaged. I also checked All Data and they said it could possible cause valve damage. Should you need further help please just ask. Please rate the quality of your answer. Thank You for using Fix Ya. Roger39f6dc5.jpg

Posted on Oct 17, 2009

  • 303 Answers

SOURCE: no spark on 4 pistons out of 6

If you put marks on correctly just leave it alone and look at plug wires, cap and roter and possible coil or coils.

Posted on Jan 19, 2010

jharvey572
  • 447 Answers

SOURCE: I was replacing the timing

it should tell you in the manual which piston should be top dead centre before you ajusting the timeing belt

Posted on Jul 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi can u pls assist me with the timing marks for this car chevy aveo 1.5 engine 8 valve 2006 model hatch back pls urgently & also head bolts torque setting


Your timing marks should be on the belt. There are two single lines and one double line across the surface of the belt. Each of the single lines line up with the cam shaft and the balance shaft drive gears. The double line lines up with the crank gear. If I remember right, there is a small mark on the oil pump housing that the crank mark lines up with and the cam mark is straight up and there are 2 other marks on the cam gear that line up with the head.

Jun 05, 2015 | 2006 Chevrolet Aveo

2 Answers

Timing belt setting


line up the marks on crank shaft gear arrow to arrow, the front cam gear the mark goes to the middle on the rear cam gear the mark goes one notch below front gear mark they line up when the tension is put on belt.

Aug 17, 2014 | 2005 Chrysler PT Cruiser

1 Answer

I need timing marks for a new timing belt


Hi Jan, The timing marks are as follows. The cam gear has a hole drilled through and this must be lined up with a punch mark on the cam bearing cap behind it. We find a flash light and a mirror are good tools to use. The crank shaft is on the oil pump housing and slightly raised. It is past TDC and lined with a notch in the crank pulley.Regards John

Nov 12, 2011 | 1994 Toyota Camry

1 Answer

Show me where are the timing marks on 2.0 toyota camry engine


the cam gear has a round hole that you will have to use a light and a mirror to look through the hole and see the t mark . put cam gear at 12 oclock and look through the hole and you will see a straight line on cam cap just below valve cover and you might have to clean the cam cap off to see it. on the outside of the crank gear there is a mark between the teeth just to the right of the key way slot. on the oil pump there is a dot at about 1-3 oclock and you might have to clean off the oil pump to see it. put crank gear on and line up the marks then on the cam gear look in the hole and put the line on cam cap in the middle of the hole.put belt on and get all the slack out that you can putting the slack towards the tensioner trying not to move the gears and check your marks and if all good release the tensioner and then tighten. put the crank bolt in and turn the engine over 360 degrees and recheck marks and if all good check to see if there is any slack in belt towards the front of car.if there is take a 14mm wrench and put on cam bolt and lightly tap on it towards the firewall to get the slack out and release tensioner and retighten double check t marks and you should be on the road again.

Jun 17, 2011 | Toyota Camry Cars & Trucks

1 Answer

2002 chrysler sebring how to set correct time


The only way to set correct time is by putting the marks on the crank and cam gears in line with the marks on the timing housing or block. Other then that there is no way to adjust timing.

Mar 26, 2011 | 2002 Chrysler Sebring

1 Answer

How do i mark my timing belt and take it off while doing a head gasket job on a 91 honda accord lx


put it at top dead center, also when you remove the cover rotate until mark on crank gear lines up with mark on oil pump housing ,it right behind the gear, also you will see notches on the cam gears and the rear cover those should also line up when crank gear is aligned, sometime marks on cams are 180 degrees off which just means crank has to be turn one more time, then double mark gears that all, good luck.

Nov 13, 2009 | 2001 Nissan Quest

1 Answer

How to you install a water pumpon a 3.5 97 dodge


Remove the hood bracket bar, 4bolts, then the fan shroud assembly, then the belts, belt adjuster, and timing covers, line up the cam gears, crank gear to the marks , cam has 1 dot, they line up to timing housing 2 dots, (single dot to middle of the 2 dots), crank has 1 dot to mark on the oil pump housing to your right of crank gear, thats TDC. now remove the timing belt tensioner, 2 bolts, and remove the belt, if the pump has leaked, replace the belt, and tensioner if it is NOT metal Pulley, the fibre one will break down from the antifreeze. its a good idea to replace the water pump housing orings behind it, ac bracket has to come off, as the right cam on engine, this not a retiming iussue with the gear. GOOD LUCK. RDJRP

Aug 17, 2009 | 1997 Dodge Intrepid

2 Answers

What is the timing marks for a 2000 kia sportage?


the timing marks are as follows... if you are not able to see the picture the intake cam gear will line up with the mating mark on the rear cover .... the "I" needs to be straight up... the exhaust cam the E needs to be straight up. the crankshaft mark is a nothch in the rear of the crank gear which needs to line up with a pointer on the front of the aluminum oil pump housing. the keyway on the crank needs to be vertical. the marks on the rear cover are dimples in the cover. this is an interferance engine DO NOT ROTATE CRANK OR CAMS WITH BELT OFF. IF YOU HAVE BROKEN THE TIMING BELT DAMAGE TO ENGINE HAS ALREADY OCCURED AND YOU WILL NEED A VALVE JOB!!!! there is no exception on this engine. if you have tried to crank it over and the belt is broken the head is no good!

08f78e3.jpg

Jul 07, 2009 | 2000 Kia Sportage

1 Answer

Changed timing chain and need to align to cam with the crang


Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

May 22, 2009 | 1995 Saturn Sl

1 Answer

Timing gear set


That is a dual overhead cam engine. On the oil pump housing there is an arrow cast into the housing. Line the arrow on the crank pulley up with the arrow on the oil pump housing, that will set your crankshaft in time. Next you'll need to set your camshafts. This is the procedure for doing that......the exhaust cam gear (nearest the firewall) has markings on it that say "2.4L" on one side and "up^" on the other side. On the left side of the gear is a notch on the tooth. This notch MUST be set at 3:30 and the intake cam at EXACTLY 9:00. Once you've installed the timing belt and you rotate the tensioner to "tighten", the offsetting of the exhaust cam will match up with the intake cam. And presto!!! your timing is now set. Make sure you turn the crank sprocket TWO complete revolutions and verify your timing marks.

Chris

Nov 08, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...